Washer Parts

We order the part to you. Read more

I replaced the dispenser assembly and since this was being replaced, I installed a new drawer and detergent box assembly. Read more

Watched a quick YouTube video. Read more

Its under warranty so I called Sears repair. The Technician determined the pump was bad order. After a month of waiting for Sears to order the part and the back and forth on the phone, I looked for the part myself. You guys sent the part and in 2 Days my washer is working again. No word yet, from Sears part order.. Read more

Removed valve and replaced with new one. Read more

• Will not stop filling with water

I replaced the water level switch and hose. After removing the hose, I found that it was clogged, and did not allow the water level to be sensed by the switch. A test after the replacement of the parts was successful. While filling the tub, the water shut off at the small, medium, and large levels as indicated by the switch. Read more

• Door latch failure
• Won't start
• Will not agitate
• won't spin

Replaced it with the part I ordered from you guys. I had originally had LG come and check it out but they quoted me a price 250 plus tax. I said no way this little piece can cost 1/4 of the whole washing machine. So after finding your price, I you-tubed on how to replace it and I did in 20 min. Thanks youtube and thanks to you guys for such a great price on this switch assembly Read more

I ordered the part from AppliancePartsPros.com and watched the GREAT video on how to replace it. Seriously it took me five minutes and four screws. perfect replacement part and I'm back to washing 900 loads of laundry for a house full of kids!! Read more

Received repair parts very fast delivery. Easy fix! Read more

The machine stopped working with a bang. There were chunks of large metal at the bottom. The drive plate had rusted through. My first step was to put a rag in the tub drain hole and save the pump. Except for grinding/chiseling off a frozen-corroded-rusty solid mass. The repair was rather easy. A couple of channel lock wrenches and a hammer didn't budge it. A monkey wrench will just round it off. You need that 1 11/6" wrench. The spindle nut was really stuck on there for my 14+ yo washer. I... Read more

Luckily happen to be walking by when machine started to make "grinding" noise as washer tub started to hit plastic tub. Assuming by shutting down machine, prevented any more damage. Aside from noise, when we opened door, tub appeared "crooked" tilted back a lot further then normal. When we removed the rubber door seal, could spin drum and hear and see the wobble and grinding. Internet told us the possibilities and so we proceeded to break down the machine. A drill with Philips bit and... Read more

Ordered the springs and shocks. Noticed that the washer had placement for 4 springs, but the factory only installs 2 (or they forgot to install the other two on my machine). If you replace the springs, be sure to check for the spring bracket mount. You will also need those. The washer is running fine. Next I'll work on the dryer. Read more

My wife and I along with Mat on the video replaced the upper and lower friction pads, along with the balance springs. The machine runs smooth as it did new. Thank you everyone at Appliance Parts Pro and Mat. You are a great company. P.S. my wife and I should had made our own video for you since we are both in our 60s I bet it would have been funny Thanks Again. JIm & Debbie from Texas. Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

I reseached these error codes and compared them to others problems. After deciding that I was gonna order the part and fix it myself I was at ease to find out it took 10min to fix! And it actually worked! The washer was pausing during cycles, cloths were soaking wet, spin cycle only worked on drain and spin at the end of the Ioad (it would spin slowly otherwise), soap dispenser still had the soap in it or it would be filled with water after the cycle was over. I watched videos on how to change... Read more

Easily replaced the knobs Read more

I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle. https://www.youtube.com/watch?v=cQwLtRcHx9k Read more