Need Help?
Call
Cracked or broken bleach dispenser cup causing leaks or improper dispensing? This replacement cup restores proper bleach delivery. Easy 10-minute fix.
The washer would work fine except it wouldn't spin unless you opened the lid and waited a split second for it to stop. You would hear a bang, then when you closed the lid, it would spin. Since it made that bang noise, I thought the transmission was going bad, so I replaced that. Nope, still the same. So, after a little more research, I found out that the motor has to come to a complete stop for the transmission to go into spin mode. After pulling out the timer and inspecting it, I noticed... Read more
This door boot gasket seals between your washer drum and door to prevent water leaks. Replace if torn, cracked, or leaking during cycles. Confirm fit with your model number.
Replaced it with a new one Read more
The Hinge Pin is an OEM part for LG washing machines. It serves as a pivot point for the washer door, allowing it to open and close smoothly. This component is crucial for maintaining the proper alignment and function of the washer door, ensuring a secure and reliable seal during operation.
Common causes of a bad hinge pin include frequent use leading to wear and tear, physical damage from accidental impacts, or rust and corrosion over time. A compromised hinge pin can result in misalignment of the door, affecting the washing machine's ability to close properly and maintain an effective seal.
Symptoms of a bad hinge pin include:
This OEM LG part is also compatible with Sears/Kenmore models.
I opted to save myself about $600 by repairing my 8 year old LG washing machine rather than buying a new one. After watching some videos I determined what I needed upon taking my washing machine apart. I ended up replacing the tub (includes spider and shaft), since I could not get the spider part removed from the original tub, as well as the motor bolt (which had broken when I removed it from the original tub's shaft). The spider was cracked and the shaft was wobbling which caused it to... Read more
Suspension rod and spring assembly for top-load washers. Mounts between tub and cabinet to absorb vibration. Replace if cracked, broken, or corroded.
I replaced the suspension rods -- I am NOT particularly experienced with machines of any type, so it took me longer than it might have someone else, but once I figured out what I needed to do, everything went very smoothly. The washer spins like a dream now! Read more
Fix a washer that won't drain or leaves clothes soaking wet. This drain pump removes water during the drain cycle. DIY-friendly, about 1 hour to install.
I drained the pump and removed coins etc from pump drain screen. This did not solve the problem, so I called Slagers, our local appliance store in Iowa City. The repair man came out two days later in the AM. He drained the pump again and checked the codes--he had to use our wireless internet because Sprint would not work from our house to determine the error code problem. He said it was the pump. I assumed he would call his Parts Dept for price and availability. Wrong assumption! He... Read more
Fix a washer that overfills or won't start the wash cycle. This water level pressure switch detects proper fill levels. DIY-friendly repair.
Hmm...watched video after reading on web of running water problem with GE washer....common fail .....moving stuff to get to the washer took all the time, easy fix but a lot of screws to remove and looking time APP site very good, will order again if need be thanks Read more
Connects washer lid to cabinet body for smooth opening and closing. Replace if broken, cracked, or missing to restore proper lid alignment and operation.
Wrote down model and serial number. Went to The Google to find replacement part. Among other choices, A'pplaincePartsPros.com came up. Quickly found the part. More to the point (of appreciation) is that there was a video right there on the page about how to replace this part. I hadn't tought much about it, since the lid easily came off with the pin broken. Watched the video, which was well done, and followed those steps quickly and easily. All done. The postscript is that I found the part of... Read more
Washer won't spin or agitate? A worn motor coupling often causes these issues. This direct-drive part is DIY-friendly and takes 30-45 minutes to replace.
Went to appliance parts pros and typed in the problem, and they had a video on that problem and how to fix it, easy fix, ordered the part, had it 2 days later, took my washer apart while I was waiting for the part to come, and then reviewed the video several times, and then completed my repair, probably saved 150-200 dollars by doing it myself, also had my dryer conk out last year, did the same thing, looked up the problem, ordered the part, and made the repair, the pair is 20 years old, parts... Read more
The Damper is an OEM replacement part for LG washing machines. It plays an important role in regulating airflow through the machine's drying system. The damper uses adjustable louvers to direct warm air emitted during the drying cycle.
Causes of a faulty washer damper include broken internal mechanisms preventing louver movement, and restricting optimal air dispersion. Dust or mineral buildup can also impact function over time.
Symptoms of a problematic damper are
This OEM LG part is also compatible with Sears/Kenmore.
The drain pump was bad. With the help of Appliance Parts Pros, I was able to order the correct part and a couple of other things while I had the washer apart. These were the drain hose from the tub to pump and the mounting bushings that have started to degrade. The video on the site helped. Very happy the washer is working normally. Read more
Seals the washer shaft to prevent water leaks from the tub during wash cycles. Replace if you notice water pooling under your machine. Verify fit.
Used the parts and youtube video from your company. Read more
Drive belt connects the motor to the drum in your washer. Replace if squeaking, broken, or washer won't spin. Confirm fit with your model number.
I followed the AppliancePartsPros.com video where the gear case was replaced on a similar model, which gave me the confidence to replace the gear case on my washer. Read more
Fabric softener not dispensing or agitator loose? This washer dispenser cup sits atop the agitator. Simple DIY fix—twist off and replace in minutes.
Planning to spend hundreds on a new washer and was pleased to discover the agitator coupling was the only thing wrong. Very easy repair. The only additional feature we would have liked was a softener dispenser. Located a GE model of the same genre that used the same coupler and took the leap to get the agitator and dispenser cup for this model (WJRR4170). Replaced the old agitator with new one and dispenser cup. Worked perfectly! We now have a washer with dispenser that works great and saved... Read more
The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.
Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
We ordered parts from appliance parts pros and I fixed it. Read more
Prevents water leaks between washer cover and tub during wash cycles. Replace if leaking or water escapes during washing. Verify fit with model number.
Disassembled and confirmed the clutch was bad. Also noticed a slight leak from the transmission shaft seal. Ordered replacement clutch, seal and oil from appliancepartspros.com. The parts arrived very quickly and exactly as ordered. Their repair videos were very accurate and made the job easy. I accomplished a quality repair at a reasonable cost. My thanks to the folks at appliancepartspros.com for making it possible! Read more
Washer won't start or door won't lock? This door lock assembly secures the door during cycles. DIY-friendly repair, typically takes 15-30 minutes.
Disconnect existing part and connect new one. Disconnect involved removing back cover around lock and electrical connector. Also had to remove rubber gasket. Read more
Replacement dispenser hose channels detergent from the tray to the wash drum. Needed when original is cracked, torn, or leaking due to wear or rubbing.
Removed the leaking hoses and seal. Installed the new ones. They all fit perfectly. The disassembly/reassembly of the washer took the most time. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.