Wire, Harness, Power Cord

This is a replacement power cord that supplies electrical power from a wall outlet to your appliance. A fresh cord helps ensure safe, reliable power delivery when the original is damaged, overheated, or worn.

• Delivers household power to the unit's main electrical connection
• Replace if the cord is cut, cracked, burnt, loose, or intermittently powers the appliance
• Helps resolve issues like no power, tripping breakers, or visible cord damage

• Unplug the appliance and turn off the circuit breaker before starting
• Verify outlet type and cord routing match your original installation
• Transfer any cord clamp/retainer as needed and secure against sharp edges
• Inspect for proper grounding and test operation before returning to service

This factory wire harness routes electrical power and signals between the controls and internal components of your cooking appliance. Replacing a burned or brittle harness restores safe, reliable connections and helps prevent shorts or intermittent operation.

• Distributes power and control signals between the user interface/control system and internal components
• Replaces damaged wires or connectors that can cause no operation or intermittent function
• Helps address short-to-ground conditions that trip a household breaker
• Restores proper routing to reduce wire chafing and heat exposure

• Disconnect power at the breaker or unplug the appliance before servicing
• Photograph/label connections and transfer one connector at a time to match original locations
• Route along factory paths and secure with existing clips/ties; keep clear of sharp edges and hot surfaces
• Inspect mating terminals for heat damage and repair/replace affected parts before reassembly

This dryer power cord connects an electric dryer to a 4-prong household outlet. Replace a worn or damaged cord to restore a safe, reliable power connection and help prevent intermittent power or overheating at the cord connection. What it does:

• Connects an electric dryer to a 4-prong receptacle for proper power and grounding
• Four-conductor design supports modern installation requirements
• Replaces cords with cracked insulation, loose prongs, or burned terminals

• 1 dryer power cord

• Disconnect power at the breaker before servicing
• Attach to the dryer terminal block per the appliance's wiring diagram and secure the strain relief

This Power Cord Assembly restores a secure, grounded connection from your wall outlet to the washer's internal power circuit. Replace a frayed or failed cord to resolve no-power issues and maintain safe operation. What it does:

• Delivers AC power from the wall outlet to the washer's internal power circuit (line filter/control)
• Provides a proper equipment ground path for the cabinet
• Replaces damaged or overheated cords that can cause power loss
• Common symptoms include: washer has no power, won't start, intermittent power when the cord is moved, or visible cord/plug damage

• 1 power cord assembly

• Disconnect the washer from power before servicing and verify the outlet/breaker are in good condition
• Access cord connections by removing the rear or top panel per your model's service information
• Note original routing and strain relief; reinstall clips/guides the same way to prevent chafing
• Secure the ground connection and fully seat all terminals; keep wiring clear of sharp edges before testing

This replacement power cord delivers household electricity from the outlet to your appliance. Installing a new cord restores safe, reliable power when the original is damaged, worn, or causing intermittent operation.

• Supplies AC power from a household outlet to the unit
• Common fix for no power, flickering lights, or power loss when the cord is moved
• Replaces cords with cuts, cracks, burn marks, or melted areas
• Restores a secure electrical connection for safe, consistent operation

• Unplug the appliance and verify the wall outlet is working before replacing parts
• Access the cord routing and internal connections; note wire positions and routing before removal
• Transfer and secure any strain relief/clamp; keep wiring clear of sharp edges and hot surfaces
• After installation, ensure the cord isn't pinched and the plug seats fully in the outlet

This part includes replacement electrodes and a harness. This is a genuine OEM part made by General Electric and has been sourced directly from the manufacturer. This part is intended to replace damaged or defective electrodes on multiple models of gas powered stoves and ranges. These electrodes connect the spark igniters to the appliance in order to allow the gas cooktop to be ignited. If the spark igniters are not lighting, the electrodes may be the issue. Over time, electrodes can become worn or damaged and may require replacement. For safety purposes, always ensure the stove is completely disconnected from power and gas before starting the any repair work. Proper tools will be required to complete this process. Please make sure to follow appropriate safety precautions when attempting to repair any appliances. For more accurate information on how and where to install these electrodes and harness, the appropriate owner's manual and included diagrams should be referred to.As an authentic replacement part, this electrodes and harness kit is suitable for use on several different models of gas ovens, stoves, and ranges manufactured by General Electric and Hotpoint. This is a genuine part made of high-quality, durable materials and is sold individually.

This multi-wire harness connects the washer's control system to multiple components. Replacing a damaged harness restores reliable power and signal routing and can help resolve intermittent operation, error codes, or no-spin/no-drain conditions caused by broken or burnt wires.

• Distributes electrical power and control signals between the PCB and components such as the motor, drain pump, inlet valves, sensors, and door lock
• Provides factory-terminated, keyed connectors and correct routing paths for secure, plug-in connections
• Typical failure symptoms: won't start or intermittent operation, component-related error codes, no spin/drain/fill, or visible heat damage to wires/connectors
• Using the exact harness maintains proper connector types and lengths for your appliance's design

• Disconnect power and turn off water supply before servicing
• Access the harness by removing panels as needed; take photos to document original routing and connections
• Transfer plugs one at a time; match keyed connectors and do not force them into place
• Secure the new harness under factory clips and away from sharp edges or moving parts; test operation before reassembly

The Power Cord is an OEM component compatible with Whirlpool washing machines. This power cord safely transmits electricity from the wall outlet to internal control boards and heating elements. Maintaining its integrity is vital for safe operation. 

Causes of bad power cord include cracked or worn insulation exposing live wires over multiple years of use. Repeated bending during installation can cause breaks in the internal copper strands.

Symptoms of a bad power cord include: 

• Intermittent power or failure to turn on fully  
• Tripped circuit breakers during heavy usage cycles
• Frayed or cracked areas increase shock/fire hazard
• Discoloration or brittleness indicating advanced breakdown

This Whirlpool replacement cord restores reliable power delivery. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This high-voltage spark ignition harness carries the spark module's output to the burner igniters so your gas burners light reliably. Replace a cracked, shorted, or burned harness to restore consistent ignition and reduce misfires or arcing.

• Distributes high-voltage pulses from the spark module to the burner igniters
• Insulated leads help prevent arcing, cross-firing, and shorts to chassis
• Failure symptoms can include no or weak spark on multiple burners, intermittent lighting, or visible burn/arc marks on the wiring
• Useful when the spark module and igniters test good but ignition remains unreliable

• Disconnect power and shut off gas before servicing; high voltage is present during operation
• Note original routing; keep wires away from sharp edges, moving parts, and hot surfaces
• Seat boots/connectors fully on the spark module and igniters; avoid kinking or stretching leads
• After installation, restore power and test spark at each burner before final reassembly

This fan and pre-wired harness assembly drives airflow to the Quick Chill/CustomCool drawer so foods and beverages chill faster and hold the set temperature. Replace a noisy, non-running, or intermittent fan to restore proper drawer cooling.

• Circulates cold air into the Quick Chill/CustomCool/deli drawer for targeted cooling
• Helps correct no-chill or slow-chill performance in the drawer
• Addresses symptoms like no airflow, intermittent operation, or grinding/buzzing noises from the drawer area
• Replaces a failed fan motor or damaged wiring harness in this assembly

• Disconnect power before servicing; remove the drawer and covers to access the assembly
• Note wire routing and connector locations; transfer any original mounting hardware as needed
• Seat connectors fully and route harness away from moving parts to avoid pinching
• Restore power and verify the fan runs and airflow is present to the drawer

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

The Refrigerator Power Cord is designed to provide a reliable and efficient power connection for your Samsung refrigerator. This genuine OEM part ensures compatibility with a wide range of Samsung refrigerator models, delivering consistent performance and safety. Crafted with high-quality materials, the power cord is durable and built to last, reducing the risk of electrical issues and ensuring uninterrupted operation of your appliance. Installing the Refrigerator Power Cord is straightforward, allowing you to quickly restore your refrigeratorGÇÖs functionality without hassle. By choosing this genuine OEM part, you can trust that your Samsung refrigerator will receive the exact components it needs for optimal performance. Whether youGÇÖre replacing a damaged or worn-out cord, the Refrigerator Power Cord offers a dependable solution to keep your kitchen running smoothly and your food fresh. Enhance the longevity and efficiency of your refrigerator with this essential power cord replacement.

This contact assembly restores a reliable electrical connection within an appliance's control circuit. Replacing worn or pitted contacts helps eliminate intermittent operation and arcing so the controlled component can turn on and off consistently. What it does

• Provides the conductive interface that completes the circuit when the control is engaged
• Helps deliver stable power to the connected load
• Typical failure signs: intermittent operation, no operation of the controlled component, visible heat damage/pitting on contacts, arcing or buzzing at the contact point

• 1 contact assembly

• Disconnect power to the appliance before servicing and verify no voltage is present
• Access the control area; photograph or label wire positions and terminal orientation
• Move wires one at a time to the new assembly; ensure tight, clean connections
• Inspect nearby wiring for heat damage and replace any burnt terminals; test operation before reassembly

The Refrigerator Compressor Wiring Harness Assembly is essential for maintaining the electrical connections within your Samsung refrigerator's compressor system. This genuine OEM part ensures reliable performance and seamless integration with your appliance. Designed specifically for Samsung refrigerators, it guarantees a perfect fit and easy installation. The wiring harness facilitates efficient power distribution to the compressor, enhancing the overall functionality and longevity of your refrigerator. By replacing a faulty or damaged wiring harness with this genuine OEM part, you can restore your refrigerator's cooling performance and avoid potential electrical issues. Durable and built to meet Samsung's high standards, this Compressor Wiring Harness Assembly offers a dependable solution for your refrigerator repair needs. Protect your investment by choosing a genuine OEM part that ensures compatibility and optimal performance, providing peace of mind and uninterrupted use of your refrigerator.

This wire harness connects the ice maker's cutter grid to the appliance's electrical system, supplying power so the heated grid can slice the ice slab into cubes. Replacing a damaged harness helps restore consistent cube separation and production.

• Routes electrical power to the cutter grid/heating wires
• A failed, loose, or heat-damaged harness may prevent the grid from warming
• Common symptoms may include whole sheets or large chunks in the bin, cubes not separating, or intermittent/slow ice production
• Visual signs can include melted/discolored grid connectors or broken/brittle conductors

• Disconnect power before servicing; allow the cutter grid to cool completely
• Note wiring/connector orientation; transfer one connection at a time to match original routing
• Seat connectors fully and secure the harness in original clips/standoffs away from sharp edges
• After reassembly, restore power and verify the cutter grid warms during a cycle

This wire harness routes power and signals between the washer's control and multiple components. Replace a damaged harness to restore dependable operation when wiring is cut, brittle, or connectors are heat-damaged or corroded.

• Distributes electrical power and communication between the control board and components such as the motor, pump, valves, door lock, and sensors
• Maintains safe, reliable connections when insulation and terminals are intact
• Typical failure signs: intermittent operation, no start, specific loads not working (pump/motor/valves), or error codes traced to wiring faults
• Visible damage like chafed wires, broken connector locks, or burned/corroded terminals indicates replacement

• Disconnect power and turn off water supply before servicing; wear cut-resistant gloves
• Photograph and label connectors; move one plug at a time from old to new to avoid miswiring
• Route along original clips, channels, and grommets; keep wiring clear of sharp edges and moving parts
• Ensure all connectors are fully seated; test operation before final reassembly