Wire, Harness, Power Cord

This factory wire harness is the pre-terminated wiring assembly that links key components inside your appliance. Replacing a damaged harness restores reliable electrical connections and can help resolve dead, intermittent, or erratic operation of individual functions. What it does:

• Distributes power and signals between the control and components such as motors, switches, heaters, sensors, and lights
• Provides model-specific, correctly keyed connectors and lengths for secure, clean routing
• Helps correct issues from burnt, broken, pinched, or corroded wires and loose/melted connectors
• Symptoms can include components not running, intermittent operation, error codes, or visible heat damage at connectors

• 1 wire harness assembly

• Disconnect electrical power before servicing; if applicable, also shut off water or gas supplies
• Photograph existing routing and connections to match the original layout during reassembly
• Route the new harness away from sharp edges, moving parts, and hot surfaces; secure with existing clips/ties
• Seat each connector fully until locked; inspect mating terminals for heat damage and address as needed

This supply cord assembly connects the appliance to household power using 18-gauge wiring and a factory-installed push-tie strain relief, replacing a damaged or frayed cord to restore a safe, reliable connection. What it does:

• Provides the electrical connection between the appliance and the outlet using 18 AWG conductors.
• Secures and routes the cord with a built-in push-tie strain relief to help prevent wiring stress.
• Replaces cords that are cut, frayed, burned, or causing intermittent power.
• Restores reliable power delivery when a damaged cord is the source of power loss or flickering.

• One supply cord assembly (18 ga) with factory-installed push-tie.

• Always disconnect power at the breaker or unplug the appliance before servicing.
• Match wire colors and secure connections per the appliance wiring diagram; ensure the push-tie/strain relief is seated properly.
• After installation, restore power and verify normal operation; if issues persist, stop and consult service.

Replacement power cord that restores the electrical connection so your appliance receives safe, consistent power. Use this cord to replace frayed, damaged, or non-functioning cords and help return reliable operation to the appliance. What it does:

• Restores the appliance's main power connection so it can turn on and operate.
• Commonly used when a cord shows frayed insulation, exposed wires, scorch marks, or intermittent power.
• Can address issues where the appliance does not power on due to a broken or damaged cord.
• Replaces cords with loose or damaged plug/terminal connections that may cause sparking or overheating.

• Always disconnect power at the breaker or unplug the appliance before inspecting or replacing the cord.
• Verify the cord configuration (3-prong vs. 4-prong) and terminal type match your appliance and local electrical code before installation.
• Use proper strain relief and routing to prevent pinching; secure all connections and replace any damaged terminal hardware.

This dishwasher power cord connects your appliance to a standard household outlet. Replace a frayed, damaged, or missing cord to restore a safe, reliable power connection and help prevent intermittent power issues.

• Supplies power from a wall outlet to the dishwasher's electrical connection
• Appropriate when the existing cord shows cuts, fraying, burn marks, or melted insulation
• Supports safe restoration of the factory-style corded installation when specified for your model

• Disconnect power at the breaker before servicing.
• Route through an approved strain relief; connect hot, neutral, and ground to the marked terminals/junction as instructed by the manufacturer.
• Ensure wiring is secured and not pinched; test operation before sliding the unit fully back into place.

Washer Power Cord is designed to replace your old or damaged power cord efficiently. This genuine OEM part ensures reliable performance and safety for your Samsung washer. Crafted with high-quality materials, it provides a secure connection and consistent power supply, reducing the risk of electrical issues. The Washer Power Cord is compatible with a wide range of Samsung washer models, making it a versatile choice for your appliance repair needs. Its durable construction guarantees long-lasting use, helping to extend the life of your washer. Installation is straightforward, allowing you to restore your applianceGÇÖs functionality quickly without the need for professional assistance. By choosing this genuine OEM part, you benefit from the assurance of quality and compatibility, ensuring your washer operates smoothly and efficiently. Whether you are replacing a frayed cord or upgrading to improve performance, the Washer Power Cord offers a practical and dependable solution for maintaining your Samsung washerGÇÖs optimal performance.

The Power Cord is an OEM replacement part for Frigidaire refrigerators. As the lifeline connecting the appliance to a wall outlet, this cord safely delivers necessary voltage to operate refrigerator systems. 

Potential causes for needing a new power cord include exposure to cuts, abrasions or rodent damage over time in the storage area. Repeated bending stress during installation or removal can also wear out plastic insulation faster.

Symptoms of a faulty power cord include: 

• Refrigerator fails to power on at all
• Flickering lights or inconsistent runs of the compressor  
• Shock, buzzing or humming sounds coming from the cord
• Bare copper wire showing through damaged insulation

This power cord also fits some Electrolux and Gibson refrigerators.

This is the appliance's main power cord. It delivers household electricity to the unit so it can operate safely and reliably.

• Supplies AC power from the wall outlet to the appliance's internal wiring
• A damaged or failed cord can cause no power, intermittent power, or tripped breakers
• Replacing a worn cord can restore consistent power and improve safety

• Unplug the appliance and turn off power at the breaker before service
• Route and secure the cord to prevent pinching or abrasion

This burner wire harness connects the range/oven ignition system components so the burner safely receives the correct spark or hot-surface signal. It replaces a damaged or worn harness to restore reliable ignition performance. What it does:

• Routes electrical connections from the igniter/spark module to the burner assembly
• Enables ignition sparks or hot-surface signals to reach the burner for reliable lighting
• Can stop symptoms such as burners failing to light, erratic or intermittent ignition, or continuous clicking
• Helps prevent loose or shorted wiring that can cause ignition faults

• Disconnect electrical power and shut off gas supply before starting any repair
• Label or photograph original wiring locations to ensure correct reconnection
• Route the harness clear of direct heat and moving parts; secure with original clips or ties

This replacement power cord restores electrical connection to the appliance so it can receive mains power safely. Use it when the original cord is frayed, damaged, or no longer providing a reliable connection. What it does:

• Replaces a damaged or worn appliance power cord to restore reliable power
• Resolves intermittent power, sparking at the plug, or visible cord damage
• Provides the necessary insulated conductors for safe appliance operation
• Works as a direct cord-replacement when the original cord is defective

• Always disconnect power at the breaker or unplug the appliance before installing
• Route the cord and secure strain relief per the appliance's original routing to prevent pinching
• Ensure the cord's connector and grounding match the appliance's inlet before connecting

This replacement defrost heater warms the freezer's evaporator area during the automatic defrost cycle. It melts accumulated frost so air can circulate, helping maintain stable temperatures and preventing ice buildup on the back wall.

• Heats the evaporator to clear frost and ice during defrost
• Helps keep airflow passages and the defrost drain path open
• Common symptoms of a failed heater: heavy frost on the back panel/coils, poor cooling or warm sections, fan noise from ice contact, cooling returns temporarily after a manual defrost
• Typically located behind the rear freezer panel

• Disconnect power before servicing; wear cut-resistant gloves
• Access the evaporator by removing the freezer's rear panel; thaw heavy ice before removal
• Transfer any clips/brackets and route wires exactly as original, keeping them away from plastic parts
• After installation, ensure wiring connections are secure and the heater is not contacting plastic surfaces

A wiring harness that routes power and signals between a refrigerator's internal electrical components, helping lights, controls, fans and motors operate correctly. Replacing a damaged harness restores reliable electrical connectivity and reduces risk of intermittent faults. What it does:

• Routes power and signal connections between the control board, lights, motors, sensors and other internal components.
• Common visible issues include frayed insulation, broken or loose connectors, or heat damage at terminals.
• Replacing a faulty harness helps eliminate wiring-related faults that can cause component failures or safety concerns.

• Always disconnect power (unplug appliance or shut off circuit breaker) before inspecting or replacing the harness.
• Match connector shapes and pin counts; route the harness along the original path and avoid tight bends or pinch points.
• Secure with the existing clips or ties; replace damaged clips or protective insulation as needed.

This wiring harness connects and routes power between key refrigerator components, restoring proper electrical signals so fans, lights, compressor and ice/water functions can operate correctly when the original harness is damaged. What it does:

• Provides the factory routing and connectors to link controls, motors and sensors
• Replaces frayed, burnt or broken wires that can cause intermittent power or no-power to components
• Helps resolve symptoms such as lights or dispenser not working, fans not running, or ice maker/pump failures when wiring is the cause
• Maintains factory-style connector fit and wire lengths for correct component connections

• Disconnect power to the appliance before inspecting or replacing the harness
• Match the part number and connector shapes to the original; route and secure wires per factory clips to avoid heat or pinching
• If connectors are corroded or terminals are damaged, replace the harness rather than attempting temporary repairs

This ignitor harness connects the oven ignitor to the range's wiring, restoring a secure electrical path for reliable ignition. Replacing a damaged harness can help get your gas oven lighting and heating properly again. What it does:

• Transfers power from the oven wiring to the ignitor so the burner can light.
• Replaces frayed, burned or broken wires that can cause intermittent ignition or no ignition at all.
• Improves connection integrity to reduce sparking or loose-contact symptoms.
• Common symptoms this part can address: oven won't light, bake/broil doesn't heat, or ignitor fails to glow.

• Turn off electrical power and gas supply before starting any work; ensure the appliance is cool.
• Remove access panels and disconnect old harness at terminals; compare connectors before installing the new harness.
• Make secure, tight connections and route the harness away from sharp edges and high-heat surfaces.

Wire harness with LED assembly that connects an appliance's control circuitry to an LED indicator or lighting module, restoring proper indicator illumination and signal routing when the original harness is damaged or intermittent. What it does:

• Provides the electrical connection and mounted LED used for control/indicator or internal lighting circuits
• Transfers power and signal between the control board and the LED/indicator
• Can correct symptoms such as a dim, flickering, or non-lighting indicator or intermittent LED function
• Replaces a damaged or corroded connector that causes loss of indicator/lighting

• Disconnect power to the appliance before attempting replacement to avoid shock or damage
• Handle connectors and the LED assembly carefully to avoid bending pins or damaging wiring
• Route and secure the harness to match original routing and avoid pinch points or heat sources
• Test operation after installation; for wiring diagrams and connector locations

This element wire harness connects the heating element to your range or wall oven's internal wiring, delivering power for proper heating. Replace a burned or brittle harness to restore consistent oven performance and safe, reliable operation.

• Supplies electrical current from the appliance wiring to the heating element
• Maintains secure, heat-resistant connections at the element terminals
• A damaged harness can cause no heat, slow preheats, or intermittent heating
• Visual clues include burned insulation, discoloration, or loose/melted connectors at the element

• Disconnect power at the breaker and allow the oven to cool completely
• Access element connections from the rear panel or inside the oven (model dependent)
• Note routing; move one connection at a time to the new harness and ensure terminals are fully seated
• Route wires away from sharp edges and hot surfaces; verify secure connections before restoring power

This wire harness is a factory-style replacement assembly that restores electrical connections between appliance components for reliable operation and diagnostics. It helps reestablish power and signal paths to controls, motors, lights, and sensors. What it does:

• Replaces damaged or frayed wiring to restore electrical continuity and reduce intermittent faults
• Connects control board, motors, lights, and sensors so components can receive power and signals
• Helps stop symptoms such as loss of lights, unresponsive controls, or intermittent motor operation
• Provides the correct connector fit and wire routing to match factory configuration

• Always disconnect power to the appliance before inspecting or replacing wiring
• Compare the new harness to the original and route connectors the same way to avoid pin mis-matches
• Secure harness with existing clips or fasteners; do not pinch or excessively bend wires