Need Help?
Call
Overlay faceplate with printed graphics that adheres to your range control board. Replaces damaged, cracked, or peeling faceplates with faded graphics.
I unplugged the oven and then removed the back panel. Next I started started removing cables from the old control board one by one, being careful to plug them into the same place on the new board. There were some slight differences in where some cables were located, but the ports are labeled and you can just match it that way. Then I applied the new faceplate to the new control board. I unscrewed the old board and screwed in the new board. Very easy replacement. Read more
Black support frame that holds the touch keypad and control interface on your range. Replace if cracked, warped, or damaged to restore secure mounting.
Removed the surrounding bezel, unplugged the bad part and plugged in the new one. One consideration, the plug is a little tricky, press each side of the plug, pull outward 1/8 " the old wiring should then slip out. Reverse procedure to install. Read more
Membrane switch keypad mounts behind the control panel. Replace if buttons are unresponsive, cracked, worn, or the overlay is peeling or damaged.
Literally took no more than 15 minutes. I unscrewed the back panel of the door, unplugged the old keypad and pealed off the old keypad. I used rubbing alcohol to thoroughly clean the surface where the new keypad would go. Then I slid the new keypad into place and plugged it in. Peal off the adhesive backing and stick the new keypad down, reattach the door panel and you are good to go. Read more
Black graphic overlay that adheres to your range control panel. Replaces worn, bubbled, or damaged film to restore clear button labels and a clean look.
I read that the controller and probe controlled the oven temperature. Also read if replacing controller you should replace the overlay. So I ordered all three parts and installed myself with no problem. I took a photo with my phone prior to unplugging wires so I knew the right way to plug the wires into the new controller. Works like new. Only need a nut driver and screwdriver to repair. Job from star to finish approximately 30 minutes. Read more
Adhesive control panel overlay that restores faded, peeling, or bubbled button labels on your range. Replace when graphics become unreadable or worn.
Replaced control board and overlay, only took 15 minutes, oven works again and it saved me $900 which is what a new stove would have cost. Read more
Replace worn or faded dispenser control labels that make settings hard to read. This overlay restores clear ice/water markings. Simple peel-and-stick fix.
Painted change water dispenser control panel to match oem. Read more
Replaces the thin faceplate over your range control panel. Restores clear button labels when original is worn, peeling, or faded. Easy peel-and-stick.
Tried to replace the temperature probe first without testing with ohm meter; decided to take a chance. I then ordered the EOC timer/oven control. Now works great and also gained the seconds timer along with minute timer that was not stock with the first timer. Happy man; didn't have to pay the labor to install the parts, the videos gave me the confidence that I could complete the repair. Read more
Black overlay that adheres to your range control panel. Replace if cracked, damaged, or worn. Peel-and-stick installation over the control board.
The entire control board was replaced. It was quick and easy! The entire repair took a total of 10 minutes, including testing. Be sure to order the new overlay, its permanently stuck to the face of the board. Read more
Fix a blank or unresponsive ice and water dispenser display. This touchpad interface assembly restores control panel function. Moderate DIY repair.
I replaced the Dispenser's Interface board assembly Read more
Fix dispenser lights not working or unresponsive touch controls. This glass touch dispenser assembly restores water and ice dispensing on your refrigerator.
Replaced the dispenser control panel. Read more
Replace your dishwasher's membrane touch pad keypad when buttons become unresponsive, cracked, or worn. Installs behind the control panel for reliable use.
Got on your web site, put in the model number and bingo a list of common problems was displayed. Clicked on the start button problem link and up came the suggested part. Your web site said that you had the part that I needed so next I clicked on the video that demonstrated how to replace the part. Ordered the part and selected next day air delivery. The next day the part arrived before 10:30am. Thirty minutes after opening the box, my GE Monogram Dishwashing was running like a Swiss... Read more
Replaces the front control panel on your range when cracked, loose, or control markings are worn or unreadable. Restores a secure, clearly labeled surface.
We updated a 'not so old' Biscuit GE Range to BLACK. It was easy to figure out what parts I needed by using the selection process on the web-site, I ordered parts then followed the pictures and videos provided to change out the handle, panel, drawer and knobs, I used two metal look back splash panels on the door to give it a rustic look and am very happy with the result. The range looks great in my newly remodeled kitchen Read more
Adhesive graphic label for your range's electronic control panel. Replaces worn, faded, or unreadable button markings. Restores a clean console appearance.
I looked up the part numbers, ordered them from Appliance Parts Pro and they arrived the next day. Followed the video to replace the parts - it was super easy and now everything works great again! Saved lots of time and money. Read more
Fix unresponsive ice or water dispenser buttons with this control panel. Snaps into place on the dispenser assembly. Moderate DIY difficulty.
Replaced interface panel. The panel was hard to pull off. Read more
Replace your oven's touch pad control panel if buttons are unresponsive, cracked, or worn. Includes membrane switch for restoring keypad functionality.
Changed the control board and keypad. An used keypad that was installed worked for a few days but was damaged by the control board. I would always change both parts at the same time with new replacements just in case. Read more
Adhesive graphic overlay that covers the electronic control panel with printed button labels. Replace when the original becomes worn, faded, or damaged.
Replaced clock/timer, watched video on parts order page it took me step by step it took less than 30 minutes to do repair, video was very important part of repair Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.