Dispenser Parts

If rinse aid is leaking or the cap is broken, this dishwasher rinse aid dispenser cap restores proper release. Moderate DIY repair for most users.

Detergent cup not opening during wash cycle? This actuator lever connects the timer to the dispenser lid. Moderate DIY repair, about 35 minutes.

This dispenser is the door-mounted assembly that delivers ice and/or water from the refrigerator. It replaces a worn, cracked, or malfunctioning dispenser to restore normal dispensing and stop leaks. What it does:

• Provides a finished dispenser opening and support for the actuator and chute so water and ice flow correctly.
• Stops leaks and prevents food or debris from entering the dispenser area when cracked or damaged.
• Restores proper activation when the dispenser lever or paddle no longer engages the valve or auger.
• Helps eliminate jams or misalignment that can cause intermittent dispensing or noisy operation.

• Disconnect power and shut off the water supply before starting any work.
• Remove the inner door panel or trim to access the dispenser mounting screws and wiring.
• Handle gently to avoid cracking surrounding trim; test operation before reassembling the door.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

If your washer dispenser drawer won't open or the handle broke off, this dispenser drawer handle restores access to detergent compartments. Easy DIY fix.

For single drain outlet models only. For dual outlet port models you must order the complete pump and motor WD26X10013.

Softener not dispensing or leaking? This washer dispenser assembly holds and releases fabric softener during rinse. Fixes clogs and cracks.

Mounts over the dishwasher's drying fan vent opening to shield the blower and direct airflow into the tub. Replace if cracked, damaged, or missing.

Fix a broken or cracked detergent tray with this washer dispenser drawer. Holds and releases detergent and fabric softener. Easy DIY install.

This dishwasher dispenser stores detergent and rinse aid and releases them at the correct points in the cycle to support consistent cleaning results. Replace a broken, stuck, or leaking dispenser to restore reliable detergent delivery.

• Holds detergent and rinse aid and dispenses them automatically during the wash and rinse portions of the cycle
• Door/actuator mechanism controls the timed release of detergent
• Seals help prevent leaks around the dispenser opening
• Typical failure symptoms: detergent cup won't latch or open, detergent left in the cup, rinse aid not dispensing, or leaks from the dispenser area

• Disconnect power and turn off water supply before servicing
• Remove the inner door panel to access the dispenser; disconnect the wire connector
• Release mounting screws/clips, clean the door cutout, and seat the new dispenser evenly
• Tighten screws in a cross pattern to compress the gasket uniformly; run a test cycle to check for leaks and proper operation

Ice maker not filling or water spilling? This fill cup directs water into the ice maker mold for proper ice production. Simple clip-on install.

This handle assembly replaces a damaged or worn refrigerator door handle, restoring a secure grip and normal door operation. It provides an OEM-fit replacement that mounts in the factory handle location for a neat, finished look. What it does:

• Replaces a broken, cracked, or loose refrigerator door handle
• Restores a solid grip for opening and closing the door
• Helps prevent further damage to the door trim or handle mounting area
• Keeps the cabinet appearance consistent with the original finish

• Disconnect power and remove food from the door area before starting work
• Use appropriate hand tools to remove mounting screws or caps; retain fasteners for reassembly
• Align assembly with mounting posts and secure without over-tightening to avoid cracking
• If door trim or mounting hardware is damaged, inspect and replace as needed for a secure fit

If your dishes have spots or dry poorly, the rinse aid dispenser may be clogged or leaking. This tank assembly restores proper rinse aid delivery.

Replacement outer door panel cover for dishwashers. Restores exterior appearance and shields internal components. Needed when original is cracked or damaged.

Fix a broken or missing dispenser drawer handle that makes it hard to open your washer's detergent compartment. Simple snap-in installation in minutes.

Detergent won't dispense or leaks during cycle? This dishwasher dispenser lid assembly seals the compartment and ensures proper opening. Quick fix.