Parts for Ge GSH9NGYCBB: Ff Section Parts

Secures the condenser unit in your refrigerator. Replace if loose, broken, or causing vibration noise. Verify fit with your model number before ordering.

Replacement bucket bottom cover cap for your refrigerator. Installs on the lower bucket assembly. Replace if cracked, broken, or missing to restore appearance.

Replacement ice chute door guide for your refrigerator. Installs inside the dispenser area to direct ice properly. Replace if cracked or broken.

Replace your refrigerator's light lens cover to restore proper illumination. Install when cracked, yellowed, or missing. Verify fit with your model number.

Air separator divider for side-by-side refrigerators. Replaces cracked, broken, or missing air flow dividers in the fresh food compartment.

Replace your refrigerator's condenser air baffle to restore proper airflow routing. This plastic baffle directs air through the condenser coils.

Secures wiring harnesses and cables inside your refrigerator. Replace if broken, cracked, or missing to prevent wire damage. Verify fit with your model.

Freezer air duct plenum extension that clips into the duct opening to direct airflow. Replace if cracked, broken, or missing to restore proper air circulation.

This wire Wine & Beverage Rack replaces a damaged or missing shelf in wine and beverage refrigerators to securely hold bottles and maximize usable storage space. It restores proper bottle support and prevents shifting during use. What it does:

• Provides stable support for wine and beverage bottles so they store evenly and don't roll or tip.
• Restores proper spacing and organization inside the cooler or wine compartment.
• Helps prevent contact between bottles and interior surfaces that can cause chips or scratches.
• Fits into the cabinet's existing rails or brackets to recreate the original storage layout.

• One replacement wire wine & beverage rack

• Unplug the appliance or switch off power before reaching into the compartment.
• Slide the rack into the existing rails or brackets; no special tools usually required.
• Handle edges carefully; avoid forcing the rack into position to prevent damage.
• If original rails or clips are damaged, inspect and replace those mounting parts separately.

Lower cabinet wire harness for refrigerators. Connects electrical components in the lower section. Replace if wiring is damaged, frayed, or corroded.

Wire harness for refrigerator internal board connections. Replace this wiring assembly if damaged, frayed, or connectors are broken or loose.

Directs and focuses interior refrigerator light for even distribution. Replace if cracked, missing, or misaligned to restore proper lighting and appearance.

Plastic spacer that positions and aligns refrigerator door components. Replace if cracked, broken, or missing to restore proper door fit and alignment.

Wire harness that connects to the dispenser motor in side-by-side refrigerators. Replace if cracked, corroded, or damaged to restore electrical flow.

Protects the auger motor and gearbox in your refrigerator's ice dispenser. Replace if cracked, broken, or missing to keep debris out and ensure proper ice flow.

Replace your refrigerator's tubular handle assembly when it becomes cracked, broken, or loose. Restores the door grip and professional appearance.

Replacement mounting screw for refrigerator installation. Used to secure components and panels. Replace if lost, stripped, or damaged during service.

Wire harness for refrigerator dispenser recess area. Replaces damaged, frayed, or corroded wiring. Essential for maintaining electrical connections.

This black plastic corner cap fits on the exterior corner of the refrigerator door, providing a finished appearance where trim pieces meet. It snaps into place to cover the joint at the door's edge. Replace this cap if it is cracked, broken, or missing, which can leave a gap and detract from the appliance's appearance.

Air return grille installs at the bottom of the fresh food compartment behind the drawers. Replace if cracked, broken, or missing after cleaning.

Rubber grommet secures the base grille on your refrigerator. Replace if cracked, worn, or missing to restore a snug fit and reduce vibration or rattle.

Foam seal for refrigerator chill compartment sides. Replace if cool air escapes or compartment temperature rises. Confirm fit with your model number.

Rear condenser fan mounting bracket for refrigerators and freezers. Replaces broken, cracked, or missing brackets that secure the fan assembly.

Evaporator front cover for side-by-side refrigerators. Installs over the evaporator coils in the freezer compartment. Replace if cracked or broken.

Replace your broken or missing tuck-away shelf assembly. This sliding refrigerator shelf restores flexible storage for bottles and tall items.

Replace your refrigerator's pan cover gasket to restore proper sealing and prevent air leaks. Slides into track on frame for easy installation. Verify fit with your model number before ordering.

Protective housing for your refrigerator's main control board. Replace if cracked, broken, or missing to secure wiring and electronic components.

This thermostat monitors the temperature near the refrigerator's interior light fixture and cuts power to the lights if excessive heat is detected. It helps prevent the compartment from overheating when the light stays on too long, such as when the door is left open. Replace this thermostat if the interior lights shut off unexpectedly or if you notice heat damage around the light housing.

Machine screw secures panels, brackets, and components in refrigerators. Replaces lost, stripped, or damaged 10-32 fasteners to restore stability.

Replacement mounting screw for refrigerator interior components. Needed when original hardware is stripped, missing, or damaged during repairs or maintenance.

10-32 x 5/16 machine-thread screw secures refrigerator panels, trim, and internal brackets. Replaces missing or damaged fasteners to prevent rattles.

This is a small 8-32 threaded nut used as a fastener in various mounting locations within the refrigerator. It secures internal components and brackets in place to maintain structural integrity. Replace this nut if it has become stripped, corroded, or lost during a previous repair, causing a loose or rattling component.

Mechanical wire actuator that connects the dispenser paddle to the activation switch. Replace if bent, broken, or missing to restore proper paddle function.

Clear dairy door bin and tray assembly for side-by-side refrigerators. Replace this compartment if cracked, broken, or missing to restore door storage.

This electronic freezer upper module controls functions for the freezer compartment, restoring proper control of temperature and related components when the original module fails. It replaces a faulty upper freezer control to help the freezer run correctly. What it does:

• Manages freezer control signals to temperature sensors, fans, and compressor circuits
• Can resolve intermittent cooling, failure-to-start, or erratic freezer behavior tied to control faults
• Stops error codes or display issues caused by a defective upper module
• Works as the direct replacement for the failed upper freezer control board

• One upper freezer electronic module

• Intended for direct replacement of the matching upper freezer control;
• Disconnect power to the appliance before starting; electrical shock hazard
• Handle the module by edges and avoid touching contacts to prevent ESD damage

Evaporator fan plenum assembly that houses and directs airflow in your refrigerator. Replace if cracked, broken, or damaged to restore proper air circulation.

Covers the water line tubing on the back wall of your refrigerator. Replace if the original cover is cracked, broken, or missing to protect the tubing.

Bottom door hinge for side-by-side refrigerators. Replaces worn, cracked, or broken hinges causing door misalignment or sagging. Direct fit.

Fresh food inlet cover for side-by-side refrigerators. Replaces cracked, broken, or missing covers that protect the air inlet opening.

Black plastic cover that conceals the upper hinge bracket on refrigerator doors. Replace this trim piece if cracked, broken, or missing for a clean look.

Black plastic hinge cover for refrigerator doors. Replaces cracked, broken, or missing covers that expose the hinge mechanism. Snaps into place.

Plastic cover that protects the damper assembly inlet/discharge area in your refrigerator. Replace if cracked, broken, or tabs are damaged.

Replacement pivot that supports and aligns refrigerator doors or drawers. Needed when original pivot is cracked, broken, or worn, causing misalignment.

Ice not dispensing or jamming? This ice dispenser auger blade moves ice from the bin to the chute. Installs in numbered sequence with spacers.

Fix ice dispensing issues with this refrigerator auger blade. Solves crushed ice not dispensing or jamming problems. Moderately easy DIY repair part.

Replacement water filter cap cover for your refrigerator. Secures and protects the filter housing. Order a new cap if yours is cracked, broken, or missing.

Replace your broken or cracked freezer door shelf module. This storage bin installs on the inside of your refrigerator freezer door to hold items.

Bottom door hinge and pin assembly for side-by-side refrigerators. Replace this structural part if cracked, broken, or worn to restore door support.

Refrigerator condenser bar bracket secures the condenser coils in place. If coils are loose or rattling, this mounting bracket may need replacement.

Top hinge and pin assembly for refrigerator freezer doors. Mounts at the top of the door to allow smooth opening and closing. Replace if cracked or worn.

Replace a cracked, broken, or missing half-basket on your freezer door. This handle basket restores secure storage for small frozen items and improves appearance.

Ice won't crush and gets stuck between blades? This moving dispenser blade restores crushing function. Simple DIY fix for side-by-side refrigerators.

A threaded mounting bolt that secures the compressor to the refrigerator's frame, providing vibration dampening and structural support. Replace when you hear excessive compressor noise, vibration, or notice the compressor appears loose or misaligned.

Replacement mounting screw for securing panels, trim, and internal components in appliances. Needed when original screws are stripped, lost, or damaged.

Foam seal strip creates an airtight barrier between refrigerator components. Replace when worn, compressed, or damaged to maintain efficiency. Verify fit with your model number before ordering.

Replace worn refrigerator door foam seal strip to improve cooling efficiency and reduce energy costs. Self-adhesive installation. Verify fit with your model.

Refrigerator plenum gasket seals air duct between fresh food and freezer sections. Replace if torn, cracked, or causing temperature issues. Verify fit with your model number before ordering.

Replace your refrigerator plenum gasket to restore proper airflow and temperature control. Install when torn, compressed, or causing air leaks. Verify fit with your model number.

Secures mobility components and wheel brackets on side-by-side refrigerators. Replace if screw is missing, stripped, or worn to restore stable mounting.

Seals the evaporator block to the freezer cabinet, maintaining proper airflow and preventing air leakage. Replace if cooling is uneven or frost builds up.

Plastic cover that protects and directs airflow around the refrigerator condenser coils. Replace if cracked, broken, or missing to shield components.

Molded duct assembly directs cold air from freezer to fresh-food section. Replace if cracked, broken, or damaged to restore proper airflow balance.

Replacement ice bucket for refrigerator ice dispensers. Stores and feeds cubed ice through the dispenser chute. Needed when bucket is cracked or worn.

Freezer not cooling or ice buildup on back wall? This evaporator coil assembly restores proper cooling. Moderate DIY repair with defrost system work.

Replaces cracked or missing light shield and housing in your refrigerator's fresh food compartment. Restores proper illumination and protects bulb. Verify fit.

Metal retainer spring secures trim panels and lightweight components in your refrigerator. Replace when worn, broken, or missing to restore snug fit.

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

Replace your refrigerator's chill drawer gasket to restore a tight seal and maintain proper temperature. Fixes worn or compressed seals causing moisture issues.

Self-adhesive foam strip seals gaps in your refrigerator to prevent air leaks and maintain temperature. Replace when worn, compressed, or damaged.

Secures the refrigerator door to the cabinet and provides a stable pivot point. Replace if cracked, broken, or causing door misalignment or sagging.

This support slide secures and guides a refrigerator freezer basket so it opens and closes smoothly and stays aligned. It replaces worn or broken slides to restore proper basket support and movement. What it does:

• Guides the basket along its track for smooth in-and-out motion
• Helps keep the basket level and prevents it from sagging or tilting
• Replaces damaged or worn slide hardware that can cause sticking or uneven travel
• Addresses symptoms like a basket that won't slide smoothly, drops, or misaligns

• One support slide

• Turn off power to the appliance and remove stored items from the basket before starting
• Compare the old slide to the new one to confirm orientation and mounting points
• Install by aligning the slide with the mounting points and securing per OEM fastener locations

Replaces a cracked, broken, or worn slide-out shelf assembly in your side-by-side refrigerator. Installs in the shelf track for smooth gliding access.

This is a self-tapping Phillips head screw used to secure various components inside the refrigerator. It measures 8-18 thread size and 1/2 inch in length. Replace if the original screw is stripped, missing, or damaged during a repair, which can cause panels or parts to come loose.

Restores smooth drawer movement in your refrigerator. Replaces worn, broken, or damaged slide and bracket assembly. Installs to support drawer glide.

Foam sleeve that insulates refrigerator tubing to reduce condensation. Replace when worn, cracked, or missing to restore padding and protection.

This self-adhesive foam strip provides a flexible seal and buffer for appliance gaps, helping reduce drafts, rattling, and moisture intrusion. Designed for easy stick-on replacement where foam padding or sealing is needed. What it does

• Seals small gaps between components to help reduce air leaks and temperature loss
• Cushions panels and doors to minimize noise and vibration
• Helps block moisture and dust from entering sensitive areas
• Self-adhesive backing allows for quick placement without extra glue

• One self-adhesive foam strip

• Surface must be clean and dry; wipe with isopropyl alcohol for best adhesion
• Measure and trim the foam strip to fit—use scissors or a utility knife
• Press firmly along the length to ensure full contact; allow adhesive to set before closing doors or panels
• For safety, disconnect power to the appliance before working in internal areas

Fix a damaged or cracked dispenser front with this housing shield. Protects internal components and restores a finished look to your refrigerator's exterior.

Drip trough assembly catches defrost and condensation water in your side-by-side refrigerator. Replace if cracked, broken, or causing leaks.

Size: 8-32 t. Includes 12 screws.

Mounting spacer maintains proper clearance between refrigerator panels, doors, or components. Replace if cracked, broken, or missing to restore fit.

This light socket connects the interior lamp to the refrigerator wiring so the interior light turns on when the door opens. It replaces a damaged or burned socket to restore reliable lighting. What it does:

• Holds the interior lamp securely and provides the electrical contact for operation
• Restores lighting when a damaged socket causes the light to fail or flicker
• Prevents intermittent connections from poor contacts or heat damage
• Works with the appliance's existing wiring and bulb style

• Disconnect power to the appliance before inspecting or replacing the socket.
• Handle bulbs and sockets carefully; use gloves to avoid cuts and for hygiene.
• Test operation after installation; replace the bulb if necessary.

Ice dispensing wrong type or jammed? This stationary blade assembly secures the blade for smooth ice crushing. Simple repair restores proper function.

Front caster assembly that mounts to the bottom of your refrigerator. Replace if cracked, broken, or worn to restore smooth rolling and stability.

Replaces worn or broken refrigerator drawer slide assembly. Restores smooth gliding and secure support for drawers that sag, bind, or no longer align properly.

Mounting standoff spacer secures internal components, panels, and circuit boards inside your refrigerator. Replace if cracked, broken, or missing.

Seals evaporator cover to cabinet, preventing air leaks and frost buildup. Replace if worn or cracked to restore proper airflow and temperature control.

Hex washer head screw for refrigerator component mounting. Replaces missing, stripped, or damaged fasteners on brackets, panels, and covers.

Refrigerator not cooling or running constantly? A damaged condenser coil prevents proper heat release. This assembly restores cooling efficiency.

Includes 12 washers.

Protects upper cavity components and restores finished appearance. Replace if cracked, broken, or missing to keep debris and moisture out of internal areas.

Replacement mounting screw for refrigerator panels, brackets, and internal components. Secures loose assemblies when original fasteners are stripped or missing.

Drawer slide liner provides smooth, low-friction glide for refrigerator drawers. Replace if cracked, worn, or causing drawer to stick or catch on track.

10-18 hex washer screw for securing panels, trim, brackets, and components in appliances. Replaces lost, stripped, or corroded fasteners.

Ice dispenser not working or making noise? The auger helix transports ice from bin to chute. DIY repair takes about 10 minutes with video guidance.

Secures refrigerator wiring to prevent chafing and vibration noise. Replace when damaged or missing to keep harnesses organized. Confirm fit by model.

Secures refrigerator panels, brackets, and trim. Replace if screw is stripped, missing, or no longer holds components tightly in place.

Replacement module shelf for the refrigerator fresh-food compartment that provides a secure mounting surface for electronic modules and restores proper shelf support and interior organization. What it does

• Provides a stable mounting surface for the refrigerator module and related components.
• Replaces cracked, broken, or warped shelves that no longer hold items securely.
• Reduces noise and movement from loose components or shifting items.
• Restores proper shelf alignment so drawers and adjacent shelves fit correctly.

• Disconnect power to the appliance before beginning any service to avoid electrical shock.
• Remove nearby shelves or drawers for access, then align the shelf and snap or seat it into the factory mounting points.
• Handle the plastic carefully to avoid cracking; do not force the shelf into position.

Intermediate freezer wire harness connects cabinet wiring to freezer components. Replace if wires are damaged, connections corroded, or harness broken.

Hex head screw for refrigerator panels, brackets, and assemblies. Replaces missing, stripped, or rusted fasteners to secure components properly.

Secures the refrigerator handle to the door. Replace this fastener if it's missing, stripped, or damaged to eliminate handle wobble and restore alignment.

Interior light not working? Replace a faulty refrigerator light socket to restore lighting. Simple hand repair with basic tools in under 15 minutes.

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.

Includes 12 retainer rings.

Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.

If your dispenser light stays off or won't turn on, this control board restores proper illumination. Moderate DIY, requires clip release and wiring.

Replace your worn or broken refrigerator bottom hinge pin. Supports the door and serves as the lower pivot point on the bottom hinge assembly.

Stores ice in the freezer and drives it to the dispenser chute. Replace this assembly when the bucket is cracked, the auger is worn, or ice won't dispense.

Front mounting grommet for refrigerator ice makers. Secures ice maker assembly to freezer wall. Replace if cracked, missing, or worn to restore stability.

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.

You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.

Symptoms of a bad R134 drier include:

• Reduced cooling efficiency
• Frost buildup on the evaporator coils
• Unusual noises from the refrigeration system
• Increased energy consumption
• Refrigerator not maintaining the set temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Cardboard or metal cover that closes the machine compartment opening on your refrigerator back panel. Replace if cracked, missing, or water-damaged.

Directs airflow from evaporator through the fresh food compartment. Replace if cracked, broken, or missing to restore proper air distribution.

Secures the lower edge of the evaporator assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.

Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.

Size: 10-32 GXTT FLP.595 S

Foam insulation wraps around your refrigerator's water reservoir. Replace if torn, crushed, missing, or compressed to prevent tank sweating and condensation.

Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.

White rear motor cover for refrigerator. Shields motor and fan area at back of compartment. Replace if cracked, broken, or missing to protect components.

Refrigerator not cooling or running constantly? This compressor powers your cooling system. Advanced repair, allow 2-4 hours for replacement.

Replace missing or stripped #8-18 x 5/8-inch Torx T20 screws in your side-by-side refrigerator. Secures panels, brackets, drawer rails, and trim.

Ice won't dispense or drive spins freely? This auger drive coupler connects the motor to the ice bucket. Moderately difficult repair with basic tools.

Replace cracked or broken ice bucket guide slides in your refrigerator freezer. Mounts to freezer wall to support and guide the ice bucket assembly.

Fixed-position freezer shelf for side-by-side refrigerators. Replace cracked, broken, or missing shelves to restore storage capacity and organization.

Protects the freezer light bulb from damage while maintaining visibility. Replace if cracked, yellowed, or broken. Confirm fit with your model number.

Plastic water line that runs from the water valve to the icemaker fill tube. Replace if cracked, brittle, broken, or leaking at connection points.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

Replaces the damaged or missing edge trim on your freezer shelf. Snaps onto the shelf frame to provide a finished lip and restore its original appearance.

White plastic clip that secures the rear of refrigerator shelves or drawer rails to the cabinet wall. Replace if cracked, broken, or missing.

Replaces the worn or cracked hinge bushing at the bottom of your refrigerator door. Installs on the lower hinge pin for smooth door movement and alignment.

Replaces broken or cracked refrigerator door stop. Installs on door to limit swing range and prevent cabinet damage. Needed when missing or worn.

Bushing that lines the upper hinge pin on refrigerator doors. Replace if cracked, worn, or missing to restore smooth door swing and proper alignment.

Protective enclosure for the ice crusher mechanism in your refrigerator's dispenser. Replace if cracked, broken, or damaged from ice jams or wear.

Slide-out freezer shelf restores storage capacity and organization. Replace if cracked, broken, or difficult to slide for smooth access to items.

Ice scattering everywhere? This deflector guides cubes or crushed ice down the chute into your glass. Replaces cracked or missing deflectors in 30 minutes.

Set screw secures refrigerator door handles in place. Replace if lost, stripped, or missing after repairs. Requires hex wrench for installation.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

Plastic bushing that fits inside the lower freezer door hinge assembly. Replace when cracked, worn, or broken to restore smooth door operation.

This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.

Replacement dispenser grill recess drip tray for side-by-side refrigerators. Collects spills and overflow in the dispenser area. Replace if cracked or missing.

The Ice Deflector Spring is an OEM replacement part for GE refrigerators. This spring is a crucial component of the ice dispensing system, specifically in selecting between crushed and whole ice cubes. It is designed to always force the diverter back in a way that the cubes get crushed. When whole cubes are selected, the solenoid pulls the lever against the spring’s tension to shift the configuration, allowing cubes to bypass the crusher blades.

Causes for a malfunctioning Ice Deflector Spring can include wear and tear from regular use, corrosion due to constant exposure to moisture, or mechanical failure that prevents it from effectively reverting the diverter to the crushed ice configuration.

Symptoms of a bad Ice Deflector Spring include:

• The ice dispenser only dispensing whole cubes, even when crushed ice is selected
• The diverter not returning to the crushed ice configuration
• Unusual sounds during the ice dispensing process
• The need for manual intervention to get crushed ice

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This helix is the plastic spiral inside the refrigerator's ice bucket that works with the auger to move ice toward the crusher and dispenser. Replacing a worn or broken helix restores smooth ice dispensing and reduces jams.

• Surrounds the auger shaft in the ice bucket to advance cubes toward the crusher/chute
• Engages when the dispenser is activated to feed ice consistently
• Replace if cracked, stripped, or warped
• Symptoms may include little or no ice dispensing, intermittent dispensing, or grinding noises from the bucket

• Unplug the refrigerator and wear cut-resistant gloves; crusher blades are sharp
• Remove and empty the ice bucket; note the order/orientation of blades, spacers, and washers during disassembly
• Transfer components to the new helix in the same sequence; reuse existing hardware
• After reassembly, verify the auger turns smoothly by hand before reinstalling and testing

Plastic shelf stop locks refrigerator shelves into liner slots. Replace if cracked, broken, missing, or lost during cleaning to secure shelves properly.

Seals the back edge of your refrigerator's crisper cover to maintain proper humidity and airflow. Replace if worn, cracked, or causing gaps. Confirm fit by model.

This black lever assembly operates the freezer door handle mechanism, allowing smooth opening and secure closing of the freezer compartment. It connects the external handle to the internal door latch system. Replace this part if your freezer door handle is loose, won't open the door, or if the handle feels disconnected when pulled.

Replaces a cracked, broken, or worn ice chute funnel in your refrigerator door dispenser. Directs ice from the auger to your glass or container.

Replacement paddle for refrigerator ice dispenser. Press to activate ice release. Replace if cracked, broken, or won't spring back after pressing.

The Screw is an OEM part for GE refrigerators. It serves a crucial function in securing and allowing smooth operation of the refrigerator's drawer rollers.

Causes of a bad or missing screw can include accidental loss during repair or maintenance, stripping of the screw threads due to overtightening, or general wear and tear over time.

Symptoms of a loose or screw include:

• Loose or wobbly refrigerator drawer
• Difficulty opening or closing the drawer smoothly
• Scraping or grinding noises when operating the drawer
• Drawer coming off the track or rollers entirely

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Directs defrost water from the evaporator to the drain pan below your refrigerator. Replace if cracked, damaged, or clogged to prevent water pooling.

The Temperature Sensor Seal is an OEM part for GE refrigerators. This seal is designed to protect the temperature sensor from moisture and other environmental factors that could affect its accuracy and longevity. By providing a barrier against the harsh conditions within a refrigerator, such as humidity and temperature fluctuations, this seal ensures that the sensor can accurately monitor and control the refrigerator's internal temperature.

Causes of a malfunctioning Temperature Sensor Seal can include wear and tear over time, degrading the seal's effectiveness. Physical damage like tears or punctures can allow moisture to reach the sensor. Improper installation may leave gaps or loose areas around the sensor, compromising the seal.

Symptoms of a bad Temperature Sensor Seal include:

• Inaccurate temperature readings.
• Condensation or frost near the sensor location.
• Frequent cycling or unusual patterns in the refrigerator's cooling process.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Ice dispenser not working or just humming? The auger motor drives ice delivery. Easy DIY fix in under 15 minutes with our video guide. Restore ice flow.

Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.

Replacement humidity control slide for refrigerator crisper drawers. Installs in produce compartment to adjust moisture levels. Needed when original is broken, cracked, or missing.

Replaces a broken or worn freezer door cam closure on side-by-side refrigerators. Installs on the door to control opening range and secure latching.

Small funnel-shaped component in the ice maker that directs water into ice molds during the filling process. Replace if the ice maker produces hollow, small, or irregularly shaped ice cubes.

This small roller wheel attaches to the underside of the pan cover or drawer cover inside the refrigerator, allowing it to slide smoothly in and out. It supports the weight of the cover panel that sits above the crisper or deli drawers. Replace this wheel if your drawer cover is difficult to slide, sits unevenly, or if the original wheel is cracked or missing.

Bypass cap allows refrigerator water and ice dispensers to work without a filter installed. Replace if cracked or leaking. Confirm fit with your model.

Replacement rear wheel for refrigerators. Mounts to the bottom rear frame to enable smooth rolling for cleaning and repositioning. Order if cracked or missing.

The Fresh Food Door Closure Cam is an OEM replacement part for GE refrigerators. It is a component located inside the fresh food door that works together with the door latch mechanism. The door closure cam has a pivoting arm that engages the latch to securely fasten the door shut when closed. For the same part in white, purchase WR02X10637.

Causes of failure include wear and tear over time from repeated usage, damage due to accidental mishandling of the door, or an impact that causes misalignment of the cam. 

Symptoms of a bad door closure cam include:

• The refrigerator door not closing properly
• A sagging or misaligned door
• Unusual noises when opening or closing the door
• Gaps in the door seal leading to temperature inconsistencies

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Fresh Food Lever Assembly is an OEM part for GE refrigerators. It plays a crucial role in the operation of the refrigerator, enabling the smooth adjustment of settings within the fresh food compartment. This lever assembly is responsible for the user's ability to fine-tune the temperature and humidity levels, ensuring that the food stored inside remains fresh and well-preserved. For the same part in white, purchase WR11X10007.

Over time, the lever assembly may become worn or damaged due to regular use, accidental impacts, or environmental factors such as extreme temperatures or humidity.

Symptoms of a bad Fresh Food Lever Assembly include:

• Difficulty in adjusting the temperature or humidity settings.
• The lever becoming loose or unresponsive.
• Inconsistent temperature control within the fresh food compartment.
• Increased energy consumption as the refrigerator works harder to maintain settings.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replacement door bin for side-by-side refrigerators. Mounts inside the door to organize condiments, jars, and beverages. Replace if cracked or broken.

Secures the auger shaft in the icemaker assembly. Replace if stripped, cracked, or loose, preventing proper ice transport from bin to dispenser.