General Electric Fuse Or Sensor

Solid-state triac that switches AC power under command of the appliance's electronic control board. Replacing a failed triac restores proper power control to heating elements or motors and resolves intermittent or no-power symptoms. What it does:

• Acts as a solid-state switch on the control board to regulate AC power to heating elements or motors
• Enables the electronic control to modulate output for temperature or speed control
• Failure can cause no heat, intermittent heating, or loss of motor control
• Designed to match the original control circuit; check board mounting and connections before replacing

• Always disconnect all power at the breaker or unplug the appliance before servicing — risk of electric shock
• This part mounts to the control board; handle the board and connectors carefully to avoid damage
• Use anti-static precautions when handling electronic components;
• Verify the part number on the original board before installation

If your range meat probe gives inaccurate readings or doesn't work, this temperature sensor monitors internal cooking temps. Easy 15-minute DIY fix.

This limit switch is a small position-sensing microswitch used in the oven door lock system. It tells the control when the latch is open or closed so the door can lock/unlock correctly and self-clean can run safely.

• Detects the oven door latch position and sends an on/off signal to the control
• Helps prevent self-clean from starting unless the latch is in the correct position
• Common symptoms: door won't lock or unlock, self-clean won't start or cancels, "lock door"/F9-style lock errors
• Restores proper latch feedback so the control knows when the door is locked

• Disconnect power at the breaker before servicing
• Access the door lock/latch assembly; note wire positions and orientation of the old switch
• Transfer wires one at a time and mount the new switch in the same orientation so the actuator engages the latch cam
• After reassembly, verify latch operation before starting a self-clean cycle

Microwave suddenly lost power or won't heat? A faulty thermostat cavity can cause total failure. This housing secures the sensor for proper alignment.

This probe thermistor monitors interior temperature and sends readings to the control board so your appliance can maintain the correct cooling cycle. It replaces a failed or inaccurate sensor to help restore proper temperature regulation. What it does:

• Senses air or evaporator temperature and reports it to the control module
• Commonly related to warm/freezing issues, incorrect temperature readings, or erratic cycling
• Used by the control system to trigger fans, defrost, and compressor operation as needed
• Works as a direct replacement for the listed OEM temperature probe

• Disconnect power before replacing to avoid shock or damage
• Handle the sensor tip and wiring gently to avoid damage to the element or insulation
• Route and secure the wiring so it does not contact moving parts or hot surfaces

5 A, 125 V electrical fuse that restores circuit protection when the original fuse is blown. Replacing the failed fuse helps prevent further electrical damage and can restore normal appliance operation. What it does:

• Provides overcurrent protection for the appliance circuit to stop excessive current flow.
• Replaces a blown or open fuse that prevents the appliance from powering up.
• Common symptom: appliance has no power or a circuit/component won't operate.
• Common symptom: intermittent power or a fuse that visibly shows a blown element.

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing the fuse.
• Replace only with the exact rated fuse (5 A, 125 V) and part number to maintain proper protection.
• Do not bypass the fuse or use makeshift substitutes — that can cause fire or equipment damage.

This switch sensor is a direct-replacement sensing device that detects the position/state of a moving component and sends that signal to the appliance control for reliable operation. It restores correct sensing when the original fails. What it does:

• Detects and reports a component's open/closed or engaged/disengaged position to the control
• Helps the appliance start and change cycles only when the mechanism is in the correct position
• Can resolve symptoms such as no response from the control, intermittent operation, or cycles that won't advance
• Provides a direct electrical/mechanical interface between the moving part and the control system

• One switch sensor

• Disconnect power to the appliance before starting any repair
• Match this part number to the failed sensor before installing
• Handle wiring and connectors carefully; avoid forcing tabs or pins
• Test operation after installation and restore power only when all connections are secure

Washer not heating or cooling properly? This thermistor temperature sensor assembly measures internal temps and sends readings to the control board.

If your air conditioner won't start or shuts down unexpectedly, a failed compressor overload protector is often the cause. This simple swap restores starts.

This thermistor is the refrigerator temperature sensor that helps the control board monitor and regulate cooling. Replacing a faulty sensor restores accurate temperature readings and consistent cooling performance. What it does:

• Measures internal refrigerator/freezer temperature and sends readings to the control board
• Helps the control board adjust compressor and fan operation for stable temperatures
• Can cause incorrect temperature display or uneven cooling when it fails
• Linked to excessive running, frequent defrost cycles, or poor cooling performance

• Disconnect power to the appliance before servicing to avoid shock or damage
• Handle the sensor and wiring harness carefully; avoid kinking or damaging the lead
• Ensure the connector is fully seated and any mounting clip or bracket is secured
• Some panel removal may be required; follow for access and reassembly

If your microwave oven won't heat properly or overcooks food, the thermostat may have failed. This temperature regulator restores accurate heating.

Oven won't heat or shuts off unexpectedly? This safety thermostat prevents overheating by cutting power when temperatures exceed safe limits.

Microwave won't heat or stops mid-cycle? This magnetron thermostat prevents overheating by cutting power when temperatures spike, then resets when cool.

Oven won't heat or overheats? This limit switch cuts power when unsafe temperatures are detected. Moderately challenging repair with basic tools.

Oven won't heat or trips during self-clean? This limit switch cuts power when temperature exceeds safe limits. Simple plug-in installation in 30 minutes.

This lower limit switch is the replacement lock-position switch used on the appliance door/lock assembly to restore proper lock sensing and control operation. Replaces a worn or failed lower lock switch to help the unit recognize door lock position. What it does

• Detects the lower/locked position of the door latch so the control can allow oven/cook functions
• Stops appliance operation or shows lock-related faults when the door isn't secured
• Commonly fails after wear, leading to lock faults, inability to start, or door-lock errors
• Works as the electrical sensor portion of the door/lock mechanism

• One lower limit switch (lock)

• Disconnect power to the appliance before starting any service
• Replacement may require removing the door or access panel and detaching the lock/latch assembly
• Handle small fasteners and electrical connectors carefully; note connector locations before removal