Need Help?
Call
The Surface Element is an OEM replacement part for Frigidaire electric ranges, designed to provide efficient and even heating for cooking on the stovetop. This component is a radiant surface element commonly seen on glass and ceramic cooktops. 8 inch, 2200 watt
Causes of a faulty Surface Element can be due to overuse causing burnout, physical damage like cracks from heavy cookware, electrical issues such as faulty wiring, and corrosion disrupting heating.
Symptoms of a bad Surface Element include:
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Changed element Read more
If your 8-inch burner won't heat or heats unevenly, this surface coil element is the fix. Direct plug-in replacement takes about 15 minutes to install.
I took the old Terminal block out and put the new one back in. it's about 15 minutes job. it was a really simple thing to do. I don't know why it always get the Terminal Block burn in every 3 or 4 months. I have to replace it all the times. I am very disappoint about the Electric Stove. The brand I have, is Hotpoint. I think about changing to Gas Stove instead soon. Read more
Burner not heating or heating unevenly? This 6-inch surface coil element restores consistent heat to your range's small burner. Simple plug-in install.
Ordered new heating coils for stove Read more
Replace a worn or broken cooktop surface element that won't heat. Direct plug-in installation takes minutes. Fits various GE electric ranges.
My 1984 GE Electric Stove model number was very close to an another entry, but not actually in appliance repair pros' model numbers list. But my burners looked and measured the same for the near entry number, and the surface unit control switch looked very similar. I decided to take a chance and ordered 2 of each.. (Actually I wouldn't have needed new burners but an earlier "repair guy" took 2 of my burners and never returned - and no one could find him!) It turned out the new burners fit... Read more
Oven not heating or baking unevenly? This lower bake element restores consistent oven temperature for proper cooking. Moderately difficult DIY repair.
Broiler not heating or element burned out? Replace this top broil element to restore radiant heat. Easy DIY fix with basic tools in 30 minutes or less.
Quick shipping, easy repair. Read more
Element not heating? This surface element is the most common fix. Compatible with Frigidaire electric ranges. Tests between 15-45 ohms resistance.
Se above Read more
Broiler not heating or browning food? A faulty broil element is often the cause. Located at the top of the oven, this part restores even heat for broiling.
Cut off power ,inside I remove the two back screws, remove the two front screws with hangers. Pull element out, clip wires so they don't fall back in holes with clothes pins. worked good. But wire connection to the broiler was to large, had to replace connectors, wire fell in hole, had to pull wall oven out and remove back panel. I then mounted the new element to oven. Replaced connectors ,connected connectors, closed back panel, put oven in place ,connected power lines. Turned power on. Works... Read more
Broiler won't heat or stays cold? This range broil element restores high-heat broiling. DIY-friendly repair, typically takes 20 minutes to replace.
I ordered a broiler element, watched the video and replaced the element when it arrived. I turned off the electrical breaker to the stove/oven. I then removed the oven door from the hinges and removed the 1/4" square head screws that secured the element in place,( the video showed phillip head screws ), removed the element wires from the old element. Replaced the element wires to the new element and reattached the element to the oven with the hex head screws. I then put the oven door back on... Read more
Electric heating element assembly that generates heat during drying cycles. Replace when the original element burns out, breaks, or fails to heat properly.
Replaced failed parts. Read more
Oven not heating or taking too long to preheat? This bake element installs at the bottom of the cavity to restore consistent heat and proper baking.
Fix an oven that won't heat or takes too long to reach temperature. This bake element generates consistent heat during the bake cycle. Easy DIY repair.
I first tried to purchase the part directly from GE but they were not helpful at all. Remembering that I had purchased a transmission and other parts from appliance parts pros for my old Maytag washer before, I searched their easy-to-use parts catalog and there it was!!!! I asked for confirmation from Customer Service and after 2 says Research confirmed that it was the correct part. Replacing the element was quite simple following the very helpful diagrams on their website. Thank you so very... Read more
Burner not heating or heating unevenly? This surface heating element restores proper heat generation. Requires removing cooktop access panel.
The Coil Surface Element is a 6-inch OEM part for Whirlpool ranges. It is responsible for radiating heat from its coils to cook food positioned above the stovetop grates.
Symptoms of a faulty coil surface element include:
Causes can be mineral deposits coating the coils over time, physical damage like bending or breaks, or standard wear of heating filaments inside.
This genuine OEM Whirlpool part is also compatible with the electric ranges of Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and Kenmore brands.
Replace burner Just like before part came fast was correct, works fine Read more
Oven won't heat or bake properly? This bake element kit restores even heating for baking and roasting. Located at oven bottom. DIY repair under 1 hour.
Following the instructions that I received through the helpful research of the APP staff, I disconnected the power, disassembled the back of the oven, and accessed the hidden element. This involved bending parts of the sheet metal and cutting the insulation, so I was very apprehensive about doing this. Once I exposed the compartment that contains the element, I had difficulty extracting the old part and was really nervous about pulling hard to extract it - until I saw the damaged element. It... Read more
Dryer won't heat or takes forever to dry? This heating element assembly fixes no-heat and weak-heat issues. DIYers report 20-30 minute installations.
We got the heater core kit. Unplug, undo two screws and pulled old one out. Looking at the old one, put the new one together and then mounted it back in place. Turned on dryer but no heat so unplugged it, tapped on elements, plugged back in and it worked. Not to hard. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.