Heating Element

This radiant surface element powers the tri-ring burner beneath your glass cooktop. Replacing a failed unit restores reliable, selectable heating across the rings so cookware warms evenly and the burner responds properly to the control. What it does:

• Supplies radiant heat to the cooking zone under the ceramic glass
• Tri-ring design lets you match the heated area to your pan size
• Common failure symptoms: burner won't heat, only one ring heats, uneven/intermittent heating, visible hot spots or breaks under the glass
• Also known in GE documentation as a "Haliant" element

• 1 radiant surface element

• Disconnect power at the circuit breaker; ensure the cooktop is completely cool
• Lift/tilt the glass top per service instructions and support it to avoid stressing the glass
• Move wires from the old element to the new one one-at-a-time to keep connections correct
• Seat the element flat in its brackets and centered under the glass before reassembly

This lower oven bake element provides the primary heat source for Bake cycles, restoring proper preheat and even, reliable cooking. Replace it if the oven won't heat, preheats slowly, or bakes unevenly.

• Heats from the bottom in Bake to reach and maintain set temperature
• Common symptoms: no heat in Bake, very slow preheat, oven temperature too low, or uneven results
• Visual clues: cracks, blisters, or burned spots on the element sheath
• If shorted, it may trip the circuit breaker when Bake is selected

• Disconnect power at the breaker and let the oven cool completely
• Remove racks, take out the element's mounting screws, and gently pull the element forward
• Hold wires so they don't retract; transfer and firmly connect the terminals; replace any heat-damaged connectors
• Reinstall element, ensure it's not contacting the cavity, restore power, and test Bake

This bake element restores even, reliable heat in the lower oven during the bake cycle. Replace it if the oven won't heat, struggles to reach temperature, or the element shows visible damage.

• Provides the primary heat source for baking in the lower oven cavity
• Common symptoms: no heat in bake, slow preheat, not reaching set temperature, uneven baking, or visible blistering/burn spots on the element
• Converts electrical energy to radiant heat for consistent oven performance

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks; take out element mounting screws and gently pull the element forward
• Support and transfer wires one at a time to the new element; ensure tight, secure connections
• Reinstall, restore power, and test for proper preheat and even heating

This lower bake element restores consistent bottom-heat for proper baking and preheating in electric ranges and wall ovens. Replacing a failed element helps eliminate undercooked centers and uneven results.

• Provides primary bake heat from the bottom of the oven cavity
• Common failure signs: no heat in Bake mode, very slow preheat, uneven baking, or visible damage
• Helps ensure stable oven temperatures when paired with a working broil element and thermostat
• Direct-fit replacement designed to connect to existing wiring and bracket mounting

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Remove mounting screws, gently pull the element forward, and transfer wires one at a time to the new element
• Avoid stressing or loosening terminal connections; secure the bracket firmly
• After reassembly, restore power and test Bake to verify proper operation

Note: Size 8 inches

The Element is an OEM replacement part for Bosch electric ranges. It generates the heat needed for baking, broiling, and other cooking functions.

Causes of a bad element can include mineral buildup interfering with heat transfer, melted or burnt connectors from overheating, or damage from impact over time. 

Symptoms of a bad element include:  

• Inconsistent or incomplete heating of the appliance
• Long preheat times or inability to reach desired temperature  
• Burned food indicating insufficient or uneven heat
• Safety issues such as sparking or smell of burning

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Main broil heating element for the oven, designed to restore top-heat for broiling and browning. Replaces a failed broil element so the oven can produce even, high-intensity heat during broil cycles. What it does:

• Generates the high, direct heat at the top of the oven used for broiling and browning.
• Restores proper broil performance when the element no longer heats or glows.
• Fixes symptoms such as no broil heat, uneven browning, visible burn marks, or a broken/warped element.
• Works as the primary upper heating element used in broil cycles (main oven).

• Disconnect power to the range/oven at the breaker before starting any work.
• Remove oven racks and access the element from inside the oven; element typically secures with mounting screws and terminal connectors.
• Handle terminals and sharp metal edges carefully; wear gloves and eye protection.

This oven heating element replaces a failed bake element to restore even, reliable oven heat for baking and roasting. It's a direct-replacement style part that heats the oven cavity when the bake function is used. What it does

• Heats the oven cavity during bake cycles so food cooks evenly
• Commonly used when the oven won't reach or hold baking temperatures
• Can fail visibly (broken or burned) or electrically (open circuit)
• Works with the oven's temperature control to maintain set temperature

• Disconnect power at the breaker before starting any repair to avoid shock.
• Handle the element carefully; connectors and terminals can be fragile.
• Confirm wire terminal fit and secure mounting; replace only with the correct OEM-style element.

Size: 8 inch. 2200 watt. Radiant.

This heater assembly restores consistent, controlled heat inside your appliance so cycles reach the correct temperature. Replacing a failed heating element assembly helps resolve no-heat complaints and performance issues that leave loads cold or extend run times.

• Generates the heat required during the appliance's heating phases so temperatures rise as intended
• Works with thermostats/sensors to achieve and maintain target temperature
• Typical symptoms: no heat, lukewarm operation, unusually long cycles, or heating-related error codes
• Often confirmed by an open element or out-of-range resistance in continuity tests

• Disconnect power and allow the appliance to cool completely before servicing
• Access the heater per the service documentation; photograph wiring and routing to aid reassembly
• Handle the element carefully to avoid bending or damaging coils; transfer any brackets/sensors from the original if they are not supplied with the new part
• After installation, inspect and clear airflow or circulation paths and verify correct voltage before test operation

This radiant surface element restores proper heat to a glass-ceramic cooktop burner. When the original element burns out or develops hot spots, replacing it brings back steady, controllable heat for everyday cooking. What it does:

• Generates heat for the selected cooking zone beneath the glass top
• Works with the surface control to cycle on/off and regulate temperature
• Helps deliver even heating across cookware
• Common fix for: burner won't heat, heats slowly or unevenly, only part of the burner heats, visible damage on the element

• 1 radiant surface element

• Disconnect power at the breaker and allow the cooktop to cool completely
• Support and handle the glass top carefully to avoid damage
• Note wire locations and transfer any mounting hardware from the old element
• After reassembly, test the burner on low and high settings

This surface radiant element sits beneath the glass cooktop and generates heat for one cooking zone. Replacing a failed element restores proper heating performance and dependable temperature response on the affected burner.

• Supplies electric heat to the selected surface burner under the glass top
• Common symptoms: burner won't heat, heats weakly or inconsistently, or only part of the ring glows
• Visual damage (burn spots/breaks) or an open reading on a continuity test indicate replacement
• Similar symptoms can also result from a faulty surface switch or wiring—diagnose before replacing

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift/remove the glass top per your service manual to access the element
• Note wire positions and bracket orientation; move wires one at a time to matching terminals
• Support the glass and avoid stressing the element; test operation before final reassembly

This Miraclon heater is a direct-replacement heating element assembly that restores proper heat generation in compatible appliances. It provides reliable, OEM-matching heating performance to help your appliance reach and maintain operating temperatures. What it does

• Replaces the appliance's failed internal heater assembly to restore heat production.
• Heats quickly and evenly to support cooking, drying, or defrosting cycles (depending on appliance).
• Common symptom: no heat or weak heat during normal operation.
• Common symptom: appliance runs but items fail to warm or dry as expected.

• Disconnect power and gas before starting any repair.
• Handle the heater carefully; avoid bending or damaging terminals and mounting tabs.
• Follow the appliance service manual for access, mounting, and wiring instructions.

This surface element supplies heat to an electric range or cooktop burner. When it fails, the burner may not heat or may heat inconsistently. Replacing the element restores steady, reliable cooking performance.

• Converts electrical energy into heat for the cooking zone
• Works with the surface control (infinite switch) to regulate temperature
• Common symptoms: burner won't heat, intermittent or uneven heating, visible breaks/blistering, burnt/melted terminals
• A failed element will not glow or reach set temperature when energized

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• If your model uses a plug-in coil style: remove the drip pan, pull the element straight out of the receptacle, and inspect/replace a heat-damaged receptacle as needed
• If your model uses an under-glass radiant style: lift the cooktop, transfer any clips/limiters from the old element, and route wires exactly as original
• After reassembly, test the burner at a low setting to ensure proper operation

1200w. Size: 6 inch. Location: Left front, right rear, and left rear.

Bottom-mounted bake element that provides the primary heat for baking. Replace when burned out or damaged to restore proper preheat and even baking.

• Supplies radiant heat from the bottom of the oven during Bake cycles
• Helps the oven reach and maintain the set temperature
• Common failure signs: no heat in bake, slow preheat, uneven results, or visible cracks/blistering on the element
• A shorted element may trip the household circuit breaker when Bake is selected

• Disconnect power at the breaker or unplug; allow the oven to cool completely
• Remove racks; take out the element's mounting screws, gently pull it forward, and move the two wires to the new element one at a time using insulated pliers
• Don't let wires slip back through the rear panel; inspect terminals for heat damage, reassemble, restore power, and test preheat

This broil element mounts at the top of the oven cavity and delivers the intense radiant heat needed for broiling. Replace a failed element to restore reliable top heat and consistent broil results in your range or wall oven.

• Provides strong, direct radiant heat from the top of the oven during the Broil cycle
• Common signs of failure: no broil heat, uneven broiling, visible breaks/blistering, or tripping the breaker when Broil is selected
• Restores proper broiling when the original element is open or shorted
• Also known as the upper/top oven element; verify fit with your model number

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the oven to cool completely and wear cut-resistant gloves
• Remove mounting screws, gently pull the element forward, and support the wires so they don't slip back through the liner
• Transfer wires one at a time to the new element, secure the element, check connections, restore power, and test