Heating Element

Oven won't heat or bakes unevenly? Replace the lower bake element to restore consistent heating. This DIY fix takes about 30 minutes with basic tools.

This is a 2500-watt circular heating element located at the rear wall of the oven cavity, surrounding the convection fan. It provides even heat distribution during convection baking and roasting by working in conjunction with the fan. Replace this element if your oven is not heating properly in convection mode, food is cooking unevenly, or the element is visibly damaged or broken.

The Surface Element is an OEM part for Frigidaire electric ranges and cooktops. It is the individual electric coil located beneath the cooktop that provides heat.

The surface element heats up rapidly upon activation in order to boil, simmer or saute foods efficiently. Its precise heating capabilities assist home cooks in meal preparation.

Causes can be mineral deposits caked onto the element surface over time reducing its ability to transfer heat properly. Excess moisture exposure can also damage internal wiring.

Symptoms of a bad surface element include:

• Burners that do not heat up at all or heat unevenly
• Lights flickering below an element when in use
• Popping, buzzing or crackling noises coming from below an element

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Fix a stovetop burner that won't heat or heats inconsistently. This 8-inch coil surface element restores reliable cooking performance. Easy 30-minute fix.

Burner not heating or center ring fails? Replace the tri-ring radiant element. Most DIYers complete this repair in 15-30 minutes with a screwdriver.

Replace a failed 8-inch radiant surface element when your burner won't heat. Restores proper heating response. DIY-friendly with basic tools.

This Miraclon heater is a direct-replacement heating element assembly that restores proper heat generation in compatible appliances. It provides reliable, OEM-matching heating performance to help your appliance reach and maintain operating temperatures. What it does

• Replaces the appliance's failed internal heater assembly to restore heat production.
• Heats quickly and evenly to support cooking, drying, or defrosting cycles (depending on appliance).
• Common symptom: no heat or weak heat during normal operation.
• Common symptom: appliance runs but items fail to warm or dry as expected.

• Disconnect power and gas before starting any repair.
• Handle the heater carefully; avoid bending or damaging terminals and mounting tabs.
• Follow the appliance service manual for access, mounting, and wiring instructions.

Restore reliable baking performance with this bake heating element. Mounted at the bottom of the oven, it provides the primary heat source in Bake mode so the cavity reaches and maintains the set temperature for consistent results. What it does:

• Heats the oven in Bake mode to reach and hold the set temperature
• Failure can cause no heat in bake, very slow preheating, or uneven/undercooked results
• Visible cracks, blisters, or a broken coil indicate the element should be replaced
• A shorted element may trip a household breaker or blow a fuse

• One bake heating element

• Disconnect power at the breaker and allow the oven to cool before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward to access wire terminals
• Transfer wires one at a time to the new element; do not allow wires to fall back into the insulation
• Reinstall the element and panels, restore power, and test bake operation

Burner won't heat or heats unevenly? This surface heating element restores reliable heat to your electric cooktop. Moderate DIY repair in 30-60 minutes.

This is a 6-inch radiant surface heating element that sits beneath the glass cooktop on an electric range. It converts electrical energy into heat for cooking and is controlled by the surface element switch or electronic controls. Replace this element if the burner fails to heat, heats unevenly, or does not respond when turned on.

Burner won't heat or develops hot spots? This radiant surface element restores steady, controllable heat to glass-ceramic cooktops. DIY repair in 1-2 hours.

Burner not heating or heating unevenly? This 8-inch surface element coil restores fast, reliable heat to your range's large burner. Easy DIY fix.

Uneven baking or convection mode not working? This rear-mounted convection fan heating element circulates hot air for consistent cooking results.

Fix a burner that won't heat on your glass cooktop. This radiant surface element restores even heating and temperature control. DIY-friendly repair.

The bake element is the lower oven heating element that produces heat during bake cycles. Replacing a failed element restores proper preheating and even baking performance when your range no longer heats correctly in bake mode.

• Provides bottom-up heat in bake mode to reach and maintain set temperatures
• Typical symptoms include no heat in bake, excessively long preheat, or uneven/undercooked results
• Visual clues of failure may include blisters, cracks, or burnt spots on the element
• A shorted element may trip a household breaker when energized

• Disconnect power at the breaker before servicing; verify no power to the range
• Remove oven racks; unfasten the element from the rear wall and gently pull it forward to access terminals
• Transfer the wires to the new element one at a time; do not let wires retract into the rear panel
• Reinstall and secure the element, ensure connections are fully seated and clear of metal, restore power, and test