By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
Need Help?
Call
Secures the evaporator fan motor inside your refrigerator. Replace if cracked, warped, or broken to restore proper motor support and stability.
I replaced the evap fan motor assembly after thawing out the evaporator. I replaced the evap motor assembly because i damaged it while defrosting the evaporator. Too much heat warped the fan blade and bracket. I replaced the motor because of the abnormal load it was put under when it was making all the noise from trying to spin through the ice buildup on the evaporator. This was all done on the fridge side. Read more
Usually ships within 4 - 14 days
Broken ice enclosure causing ice jams or warm air leaks? Replace this ice path housing. Moderately easy DIY repair—remove one screw and wire harness.
Upon receipt of part (in 2 days), removed right panel (snapped on). Removed ice tray. Removed one screw holding broken tray. Then removed plug from motor/solenoid. Next, moved motor/solenoid from old cracked tray to new one. All holes aligned exactly. Replaced shelf/motor in freezer, and reconnected cable from motor to freezer wall. Put one screw back in. Then replaced right-side snap-in panel. Finally, slid in ice-tray itself onto the new shelf. Tested okay. Read more
Housing that forms the framework for the ice crusher assembly inside your refrigerator's ice bucket. Replace if cracked, broken, or damaged to restore proper support.
The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.
Old, unused stack set. Washer was great, dryer was grinding. Started with the mounting bracket/bearing and the belt. The old ones were slightly beatup. Put it back together and the problem persisted. Found the real problem when I pulled apart the blower to get to the motor. The fan had broken fins that had jammed in the side of the blower housing, and the friction had melted through the outer wall of the fan. Got the blower housing from APP, got the fan from a competitors for $30 less. When it... Read more
Replacement top housing cover panel for range hoods. Installs as the upper cover to shield internal components. Needed when original is bent, cracked, or missing.
Replacemant part S97011445 (AP5608564) was a direct replacement. Read more
Replaces the evaporator fan orifice housing that directs airflow in your refrigerator's freezer section. Needed when original is cracked or worn.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
This is the blower housing that encloses the dryer blower wheel in a washer/dryer combo or laundry center unit. It directs airflow from the dryer drum through the exhaust system to properly vent heat and moisture. Replace this housing if it is cracked, warped, or damaged, which can cause poor drying performance, unusual noises, or air leaks during the drying cycle.
Guides airflow across the condenser and secures the fan motor in place. Replace if cracked, broken, or missing to restore proper cooling airflow.
Protective boot that covers the capacitor terminal on your range hood. Replace if cracked, torn, or missing to shield connections from moisture and dirt.
Evaporator cover shroud assembly for side-by-side refrigerators. Protects internal components and channels airflow around the evaporator coils.
Protective cover that shields the range door hinge assembly from debris and damage. Replace if cracked, broken, or missing to restore a clean finished look.
Protective cover that houses the temperature-sensing thermostat on your electric range. Replace if cracked, broken, or missing to protect internal components.
Plastic housing shield that covers and protects the refrigerator dispenser assembly. Replace if cracked, warped, broken, or missing for a secure fit.
Dryer exhaust duct outlet that channels hot air from the cabinet to the external vent. Replace if cracked, broken, or causing air leaks around the vent.
Blower housing that channels airflow from the motor into ducts. Replace if your fan scroll is cracked, warped, or missing to restore proper air circulation.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.