Switch

This genuine wire harness connects the appliance's electrical components, restoring reliable power and signal routing so controls and driven parts operate correctly. It replaces damaged or worn wiring to help stop intermittent operation and loss of function. What it does:

• Routes power and control signals between components so buttons, motors, and lights receive proper connections
• Replaces frayed, burned, or broken wiring that can cause intermittent operation or complete failure of circuits
• Helps resolve symptoms like unresponsive controls, motors that won't run, or components that power intermittently
• Provides factory-style connectors and wire lengths to match the original routing and fit

• Disconnect all power (unplug or shut off breaker) before accessing wiring
• Match connectors and routing to the original harness; avoid stretching or pinching wires
• Inspect connectors and terminals for heat damage; replace harness if any insulation or terminals are compromised

This rotary switch replaces a worn or failed control selector to restore reliable function selection. It provides a direct, mechanical interface for choosing settings so controls respond properly when the knob is turned. What it does:

• Routes user input from the control knob to the appliance's control circuits
• Restores reliable selection when a knob won't change settings or clicks without engaging
• Stops intermittent or no-response behavior caused by worn switch contacts
• Supports normal operation of the affected control bank or function

• Disconnect power (unplug or switch off breaker) before starting any work
• Label or photograph wiring before removal to ensure correct reconnection
• Access may require removing a control panel or trim; keep fasteners and small parts organized
• After installation, restore power and verify all functions operate as expected

This wire harness connects the control/switch assembly to the appliance's thermal cutoff and control circuits, restoring reliable electrical connections for proper operation. It's a direct-fit replacement when the original wiring is damaged or corroded. What it does:

• Provides the factory routing and connectors between the control/switch and TCB/thermal cutoff
• Re-establishes lost or intermittent power caused by damaged wiring or broken terminals
• Helps stop failures that cause controls to be unresponsive or cycles to stop unexpectedly
• Uses OEM-style terminals and insulation to match original fit and function

• One wire harness (switch TCB) as shown

• Disconnect power before starting — verify the appliance is completely de-energized
• Take photos of existing wire routing and connector locations to ensure correct reassembly
• Plug connectors fully and secure the harness along original clips or tie points; avoid sharp edges
• If terminals are damaged at mating parts, inspect and replace those components rather than splicing connectors

This wiring harness routes power and signals between a refrigerator's control components and electrical devices, restoring reliable electrical connections for operation and controls. It replaces a damaged or broken harness to help regain normal appliance function. What it does:

• Connects control board, sensors, lights, and other electrical components to provide power and signal paths
• Replaces frayed, burnt, or damaged wiring that can cause intermittent or complete loss of function
• Helps resolve symptoms such as lights or dispenser not working, erratic controls, or failure of specific features tied to wiring
• Restores proper connector fit and secure electrical contacts when original harness pins or wires are compromised

• One wiring harness as shown

• Always disconnect power to the appliance before starting any repair
• Match connector shapes and wire colors to the original harness; route along original paths and secure with clips or ties
• Inspect mating connectors and control board terminals for damage before installing the new harness

Fix cooktop electrical failures or unresponsive controls with this wire harness. Restores power and signal connections between components.

Burner won't adjust heat or jumps to full power? This infinite switch restores variable temperature control to surface burners. DIY install in 30 minutes.

This burner switch controls the power and heat settings for a surface cooking element, restoring reliable on/off operation, accurate temperature selection, and consistent element cycling on compatible electric ranges. What it does

• Regulates electrical power to a surface burner so the element heats to selected settings and cycles to maintain temperature.
• Replaces a worn or failed switch that causes a burner to not heat, not respond to knob changes, or only work on certain settings.
• Stops intermittent operation or arcing at the switch caused by worn contacts.
• Helps resolve a burner that stays on or will not turn on when the switch is faulty.

• Always disconnect power at the breaker before starting any repair to avoid shock.
• Photograph and/or label wires before removal so you can reconnect terminals correctly.
• Handle terminals gently and ensure secure, tight connections; replace any damaged wiring or connectors.
• Test the range on all heat settings after installation; if you see arcing, burning smell, or continued malfunction, cut power.

This right-side burner switch controls heat output on the cooktop so burners respond correctly to your knob settings. It restores proper power and temperature control for a single right-side heating element. What it does:

• Replaces a worn or faulty right burner control to restore variable heat settings
• Enables proper on/off function and temperature regulation for the right cooktop element
• Commonly used when a burner won't heat, only works at certain settings, or cycles unexpectedly
• Works with ranges that use a separate switch for the right front/right rear heating element

• Disconnect power at the breaker before attempting any repair to avoid shock
• Handle wiring terminals carefully; verify connections match the original before reassembly
• Use proper tools and avoid overtightening mounting hardware to prevent damage

This push-button door switch detects when the appliance door opens and closes to control interior circuits like the light or other door-activated features. It restores proper door-sensed operation when the original switch fails. What it does:

• Acts as the door-open/door-closed sensor for interior circuits
• Turns interior light and other door-controlled functions on and off
• Can prevent circuits from operating when the door is open
• Common symptom: interior light won't turn on or won't turn off when door is operated

• Disconnect power to the appliance before attempting service
• Handle wiring and terminals carefully; note wire locations before removal
• Test switch continuity with a multimeter after installation to confirm operation

If your cooktop burner won't heat, stays on one setting, or heats erratically, this control switch regulates power to restore proper temperature selection.

Fix a gas burner that won't light with this igniter switch. Controls the spark signal when you turn the knob. Moderately easy DIY repair.

This wiring harness assembly routes power and signals between the appliance control and electrical components so the unit operates reliably. It replaces a damaged or burnt harness to restore proper electrical connections and reduce intermittent faults. What it does:

• Connects controls, switches and motors to the main power and control board
• Restores interrupted circuits that can cause intermittent operation or component failure
• Helps resolve symptoms like lights, fans or motors not running or responding
• Replaces frayed, melted or corroded wiring that creates shorts or open circuits

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle connectors by the plug bodies; avoid pulling on wires
• Route and fasten the harness exactly as the original to prevent chafing or heat exposure

Fix a cooktop burner that won't light with this spark igniter switch. Solves clicking but no ignition issues. Moderate DIY repair, typically 30-45 minutes.

Fix a cooktop that won't spark or light with this igniter switch harness assembly. Connects spark modules to burner igniters for reliable ignition.

If your cooktop burner won't ignite or sparks continuously, the igniter switch may be faulty. This switch controls spark ignition for safe lighting.

Top burner won't cycle temperatures or respond? This range burner control switch restores reliable heat regulation. Direct-fit replacement for electric and gas ranges.