Leg Or Foot

Rubber foot for stand mixer base. Replaces worn, cracked, or missing feet. Stabilizes mixer, reduces vibration, and protects countertops.

The Roller Assembly is an OEM part for LG refrigerators. It plays a critical role in the smooth operation of the crisper drawer, allowing it to glide effortlessly in and out for easy access to your fruits and vegetables. 

Over time, the roller assembly can wear out or become damaged. This deterioration can lead to difficulty in opening or closing the crisper drawer, misalignment, or even the inability to support the drawer's weight. 

Symptoms of a bad Roller Assembly include:

• The crisper drawer sticking or jamming when you try to open or close it
• A noticeable wobble or instability in the crisper drawer
• Difficulty in aligning the crisper drawer correctly within its compartment

This OEM LG part is also compatible with some Kenmore models.

Rubber foot pad that installs on washer legs to provide stable support and absorb vibrations. Replace if cracked, worn, missing, or damaged.

Rear leveling foot assembly that supports the back of your laundry center. Replace if cracked, broken, worn, or missing to restore stability.

Replace worn, broken, or missing caster wheels on your portable dishwasher. This 4-pack restores smooth rolling and easy positioning while protecting floors.

Replace a worn rear self-leveling leg to restore a stable, level appliance. This foot supports the back of the cabinet and automatically compensates for floor unevenness to help reduce vibration, rocking, and noise during operation.

• Supports and self-levels the rear of the cabinet to maintain stability on uneven floors
• Helps address wobbling/rocking, excessive vibration, rattling or "walking," and an appliance that won't sit level
• Replaces a rear leg that is missing, cracked, or worn
• Promotes smoother operation by helping the unit sit properly level

• Disconnect power; if applicable, turn off the water supply
• With assistance, carefully tilt the appliance to access the rear base
• Remove the damaged rear leg from its mount and install the new leg, ensuring it seats fully
• Lower the unit, verify level with a bubble level, and adjust front legs as needed for final leveling

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

Leveling leg threads into the refrigerator base to support and stabilize the cabinet. Replace if cracked, broken, or worn to keep your unit level.

The Freezer Leveling Leg is an OEM part for Frigidaire upright freezers. It stabilizes and balances the appliance on uneven surfaces.

Causes relate to typical bearing wear from years of weight support. Rust forms without protective finish. Cracks develop from impact damage.

Symptoms of compromised leveling legs include:

• Excessive vibrations, noise or shaking during compressor operation
• Doors that no longer close or seal properly
• Ice maker malfunctions on frost-free models

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Adjustable leveling foot for refrigerators and freezers. Installs at the base to stabilize and level the appliance. Replace if cracked or broken.

Adjustable leveling foot threads into washer or dryer base to stabilize appliance on uneven floors. Replace if cracked, worn, or missing to reduce rocking.

Adjustable leveling leg screws into washer base to stabilize and level your machine on uneven floors. Replace worn, missing, or damaged legs for stability.

Screw that adjusts and secures the leveling leg to your range base or bracket. Replace if stripped, bent, or missing to restore stable footing and level your appliance.

Adjustable leveling foot that supports and stabilizes your refrigerator. Replace if worn, broken, or missing to eliminate wobbling and vibration.

Adjustable leveling foot that installs on the bottom of your washer to provide stable support. Replace when cracked, worn, or missing to restore balance.

This is an adjustable leveling leg that threads into the base of the dishwasher to support the unit and allow height adjustment. Proper leveling ensures the door seals correctly and water drains efficiently. Replace this leg if it is broken, stripped, or missing, which can cause the dishwasher to rock, leak, or not close properly.