Search Results

Adjustable front leveling leg for washers. Replaces damaged, broken, or missing feet that cause rocking and vibration. Installs at front base to level unit.

Replacement leveling foot supports and levels your washer for steady operation. Install this foot if yours is worn, cracked, or missing to restore balance.

The Freezer Leveling Leg is an OEM part for Frigidaire upright freezers. It stabilizes and balances the appliance on uneven surfaces.

Causes relate to typical bearing wear from years of weight support. Rust forms without protective finish. Cracks develop from impact damage.

Symptoms of compromised leveling legs include:

• Excessive vibrations, noise or shaking during compressor operation
• Doors that no longer close or seal properly
• Ice maker malfunctions on frost-free models

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replacement roller axle support shaft for refrigerators. Installs to support rotating assemblies. Replace when worn, damaged, or causing wobble.

Adjustable leveling leg threads into washer base to stabilize cabinet and reduce vibration. Replace if cracked, broken, or missing for proper support.

This replacement roller fits the front or rear position of a slide mechanism, restoring smooth, even movement and reducing noise when a wheel is worn or broken. It helps racks or drawers glide properly and stay aligned. What it does:

• Provides low-friction rolling support for the slide track
• Helps slide-out assemblies move freely without binding or scraping
• Worn or damaged rollers can cause sticking, squeaking, or uneven travel
• Restores proper alignment and smooth operation when replaced

• 1 roller assembly

• Disconnect power and allow the appliance to cool before servicing
• Remove the slide-out assembly; note roller orientation and hardware
• Transfer/reuse existing screws, clips, or retainers as required
• Do not lubricate unless the manufacturer specifies a lubricant

Adjustable

Small cabinet roller that allows your freezer to glide smoothly for cleaning or service. Replace worn, cracked, or missing wheels to restore movement.

Leveling leg assembly for washers. Installs at the corners to stabilize and level your machine. Replace if cracked, broken, or missing threads.

Threads into the washer base to adjust height and stabilize the unit. Replace if cracked, stripped, or missing to eliminate rocking on uneven floors.

Leveling foot that supports and stabilizes your refrigerator at the base. Replace if cracked, broken, or worn to keep the unit level and reduce vibration.

Adjustable leveler leg that stabilizes and levels compatible Whirlpool appliances. Replacing a worn or damaged leveler restores proper balance, reduces rocking, and helps doors and drawers align and seal correctly. What it does

• Raises or lowers the appliance to achieve a level position on uneven floors.
• Stops rocking or wobbling that can cause noise or uneven wear.
• Helps doors and drawers close and seal properly by correcting tilt.
• Replace when threads are stripped, the foot is broken, or the leg no longer holds height.

• Disconnect power (and water supply for appliances with hookups) before working beneath or behind the unit.
• Support the appliance securely (use blocks or have a helper) before removing or adjusting levelers.
• Most levelers screw in/out—turn to raise or lower, then test stability and door alignment.

Metal leveling leg screw threads into your range base to adjust height and stabilize the unit. Replace missing, bent, or stripped screws for level footing.

Front leveling leg adjusts and supports your dishwasher at the front. Replace if damaged, missing, or worn to restore proper height and stability.

This ice gear transfers motor rotation to the refrigerator's ice mechanism so cubes can be dispensed or ejected. Replacing a worn or stripped gear restores smooth, reliable ice operation and helps eliminate grinding or clicking noises.

• Transfers drive from the motor to the ice mechanism (auger/ejector, depending on model)
• Helps move ice through the system for dispensing or harvest
• Common symptoms: no or slow ice dispensing, auger not turning, loud clicking/grinding from the ice bin
• Cracked or stripped teeth indicate the gear should be replaced

• Disconnect power to the refrigerator before servicing
• Remove the ice bin and access the ice assembly per your model; note gear orientation for reassembly
• Align teeth carefully; do not force the gear onto the shaft
• Inspect related parts (drive coupler, auger, motor shaft) and replace any worn components to prevent repeat failure

Roller assembly installs on the base of your refrigerator to allow smooth movement. Replace if cracked, broken, or worn to restore mobility and stability.