Lg Parts

I ordered a new part and it came very quickly. It was nice to have my dryer back working! Read more

Replaced the water inlet valve assembly. That reduced the leakage to a smaller amount but did not fully stop the leakage. Replaced the ice maker assembly and that completed the repair. No leakage issues and ice maker is working with no issues. Read more

****** always make sure the unit is fully unplugged from the power before you do anything with the outside of the unit to work inside of the unit and while you are working inside the unit... Also make sure that you turn the hot and cold water intake valves off and make sure you don't pull too much on the two water intake hoses that lead to your washer because they can leak with too much pressure exerted on either end******* 1. Took top off unit by unscrewing mounting brackets at two similar... Read more

Ordered the plastic glides that connect to the metal rails. Super easy fix! Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

• Ice maker dispenses too much ice
• Ice maker not making ice

Replaced it very easily. Read more

We had a repair man come and tell us the needed repair at the cost of 70.00 I ordered the parts and saved money. Read more

From reading "troubleshooting" sites on the internet, originally thought I'd be replacing the front & rear drum rollers, so I ordered the rollers, and a new belt before I opened up the dryer, taking it out of use. When I opened it up the front rollers were "shot", and the front bulkhead was "totaled". Waited for parts to arrive (within 2 days), and successfully replaced front & rear rollers, bulkhead, drum seal. The on-line videos really helped me ensure I was keeping in the right order. My... Read more

Removed 2 screws from mullion strip heater and slid it up off the tabs at top and bottom. Unhooked the plug and removed it. Verified proper mullion heater and then plugged wiring connection back together, positioned slide clips back in line and slid mullion down onto the clips. Tucked the wiring back into opening positioned cover back in place and reiinstalled the 2 screws. It took about 10 minutes for the entire job. the 2nd problem was a noisy evaporator motor and is a more intense repair... Read more

The right door seal and the freezer door seal are easily removed and replaced. They just pull out of the slot. These 2 new gaskets push in easily. The left door has the French Door Mullion, that blocks the removal of the door gasket. There are two screws in the middle that holds it on, and there is a spring at the bottom of the mullion that keeps the mullion in place. The spring can easily be removed, or left in place. There is an electrical connector in the middle of the mullion. As suggested... Read more

Knowing the odds of 2 failures occurring at the same exact time was unusually high, I just searched your site for what other broken items might affect these two failures. Came up with next control item upstream and tallied that item failure with percentages of successful repairs, (4 mins.) door safety switch. Since I had to change out the most likely of the 3 and since I was already was going to be into the switch panel I ordered all 3 and swapped them all out to cover my butt, as they were... Read more

If you have an older model WM8000H_A you MUST pay attention to the type of door gasket (boot seal) that it uses. Every video I could find for replacing the seal on the WM8000HWA involved a different product than what was required for our specific washer. I wound up getting the wrong one by ordering it without help and had to exchange it - after I had the machine taken apart. Thanks to AppliancePartsPros I got the correct seal and front retaining ring the next day. NOTE! The retaining rings are... Read more

I took it apart and found the drain pump motor had come apart. I found appliancepartspros.com and read the reviews for this company. Customers were very satisfied with the parts and service. I ordered the parts (at a savings of over 30% from my local appliance store) and had them in 2 days (YES TWO DAYS). Totally excellent service. Put the washer back together and it works like new. The repair was very easy to do myself and saved me well over $100. I recommend your company to every do it... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

Replaced door gaskets with new ones Read more

Replaced the cold water valve unit (has 4 ports and 1 inlet) which is very straight forward; requires : 1 phillips screwdriver ~#2 1 needlenose plier, medium size 1 channel lock plier, medium size 1 marker pen 1 - cold water valve assembly # AP4445613 1 - hot water valve assembly #AP4441935 1 - water level pressure switch #AP4440713 an old towel or two for absorbing small amounts of water a cellphone / camera for making sure you have the... Read more