Lg Parts

• Ice maker dispenses too much ice

Replaced ice maker. Some confusion as to which part # it was as the model number cross reference shows the one I purchased was not for my model refrigerator when it actually was. Secondly, a few comments from others said the switch out was simple. Only 3 screws holding in the ice maker although one of the three was in a tight spot . That is technically true. Three screws do hold the ice maker on the door , however, you must also remove the door panel behind the ice maker to get to the wiring... Read more

If you have an older model WM8000H_A you MUST pay attention to the type of door gasket (boot seal) that it uses. Every video I could find for replacing the seal on the WM8000HWA involved a different product than what was required for our specific washer. I wound up getting the wrong one by ordering it without help and had to exchange it - after I had the machine taken apart. Thanks to AppliancePartsPros I got the correct seal and front retaining ring the next day. NOTE! The retaining rings are... Read more

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

Ordered the gasket first from Sears, but they sent me the wrong part, i.e. on the drawing on their web site the part was right (ADX73550621 - Refrigerator Door Gasket, Left), but when I received it - it was too small and didn't fit. Returned it to Sears and tried to find it somewhere else. Fortunately found the part on this site. It was helpful that the part photo was taken with an inch grid in the background, so I could compare dimensions against the old piece. The dimensions matched (wanted... Read more

I watched the Appliance Parts Pro video and saw that it was a job that I could easily do. I ordered the Rotor Position sensor switch for about $21 on a Monday and it was delivered by UPS on Wednesday. The process was straight forward: 1) remove the back cover from the washing machine (4 screws), 2) remove the main bolt holding the magnetic drum on the motor; 3) remove the 6 bolts holding the coil on the motor; 4) remove the ground screw and wire harness clamp screw; 5) take the old sensor... Read more

Conducted research on web, and via direct contact with AppliancePros where a diagnosis of replacing the water inlet valve and cleaning the sensor tube would "most probably" (80%) handle the issue. The remaining uncertainty would reside in the electronic board circuitry. The price of replacing the water inlet valve was half of a local repair call just to diagnose the issue so I decided to have faith in the odds presented to me. The part arrived on time, and using AppliancePros advice and... Read more

After my layman's diagnosis (hope) of a bad micro switch to the ice dispenser (would not activate and dispense ice through the chute) I purchased the both the ice and water dispenser micro switches (kill two birds with one stone). Albeit the video attached to these parts may be helpful to some it was not applicable to my refrigerator, as you could not access it from the front by removing the exterior dispenser plate. Don't try this on the LG, LFX25991ST series, refrigerator or you may break it... Read more

• Ice maker dispenses too much ice

Ice sensing lever (keyed onto mtr shaft) found down and would not budge. Also, test button (hidden beneath mtr) only 'beeped' when pushed. The 10 pin connector's 'clip' is also hidden against roof of freezer - mine broke but connection still seems secure. New unit was exact fit - test button (now) cycles thru one cycle of rotation and H2O fill with no beeps.... 18 hrs later, bin is half full....ice for the summer :) Remove freezer door (front) so you can lay down and look up. Cold plastic... Read more

We knew at least one door hinge cable assembly or hinge spring was broken (the door started falling down rapidly and became heavy to close) so we ordered two of each since we had read to go ahead and replace the damaged items on both sides. While we were waiting on the order, the other side must have broken-the door became incredibly heavy and instead of falling open, started crashing down unless it was carefully lowered. We feared it would fall on one of our animals and kill them. We did not... Read more

• Doesn't shut off

I only needed the Bracket Assembly motor, not the DC Motor or Fan Assembly that I also ordered so I will be sending those back. The repair was extremely straightforward with a few bumps along the way. All told it took me about an hour. I started with shutting off the breaker for the refrigerator and putting all of the frozen food in coolers. Then I removed the drawers and the bracket for the drawer rails on the left side (as your facing the refrigerator). I then proceeded to gently pry off the... Read more

Removed 2 screws from mullion strip heater and slid it up off the tabs at top and bottom. Unhooked the plug and removed it. Verified proper mullion heater and then plugged wiring connection back together, positioned slide clips back in line and slid mullion down onto the clips. Tucked the wiring back into opening positioned cover back in place and reiinstalled the 2 screws. It took about 10 minutes for the entire job. the 2nd problem was a noisy evaporator motor and is a more intense repair... Read more

• Not dispensing water
• Ice maker dispenses too much ice
• Ice maker not making ice
• Leaking

Replaced the water inlet valve assembly. That reduced the leakage to a smaller amount but did not fully stop the leakage. Replaced the ice maker assembly and that completed the repair. No leakage issues and ice maker is working with no issues. Read more

I ordered one from you and replaced it. Read more

After reading several stories online about what to replace to fix the issue with my dryer not completely drying my clothes I decided to purchase a heating assembly, a sensor and a thermistor. I am not sure which one of these three pieces corrected the issue, but my dryer is back to drying my clothes as it should. The Youtube video's are priceless in helping to find and replace the parts. Read more

The right door seal and the freezer door seal are easily removed and replaced. They just pull out of the slot. These 2 new gaskets push in easily. The left door has the French Door Mullion, that blocks the removal of the door gasket. There are two screws in the middle that holds it on, and there is a spring at the bottom of the mullion that keeps the mullion in place. The spring can easily be removed, or left in place. There is an electrical connector in the middle of the mullion. As suggested... Read more

I ordered a new part and it came very quickly. It was nice to have my dryer back working! Read more