Maytag Parts

The original pump was getting jammed intermittently, more and more often. I cleaned it out, but that didn't help the jamming. So I ordered a new pump. Have your new pump on hand and look at it to see how it attaches. The original pump, a different part number than the replacement, lasted about 7 years of almost everyday use, with multiple loads each day. My washer model Maytag MHW5500FW0 has the pump at the bottom back, in an awkward position. This took me about 2 hours due to the awkward... Read more

Replaced wheel assembly because prongs were broken and replaced track because wheel assemblies were rolling out from the track when extended. Read more

• No heat or not enough heat
• Takes too long to dry

Our 25-year-old Whirlpool dryer abruptly stopped producing heat, though it was otherwise running normally. The unit had never required service of any type and we were reluctant to replace it. After confirming that no circuit breakers had tripped, I reviewed the Whirlpool and AppliancePartsPro websites and concluded that the most likely causes of the problem were a failed heating element and/or thermal fuse. I ordered both (they arrived in two business days), installed them and the dryer... Read more

Installed new agitator Read more

• Marks left on clothes

Maytag Gas Dryer Model: MGDE300VW1 I had previous experience with repairing my dryers, but this was a first for this model. Instructional videos very helpful. Ordered necessary parts and they were delivered with-in two days. Wow! Squeak found to be coming from idler pulley roller which no longer turned freely . The four other cabinet rollers had signs of wear. Dryer belt had frayed edges and a couple of burn spots in the belt from the motor turning before the drum did. Cleaned up all shafts... Read more

• Shakes and moves

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

• Leaking

I followed your step by step instructional online video. That is one great tool you are providing for your customers! Read more

I searched the internet for the most likely cause of the problem and then went to the AppliancePartsPros.com site to see if they had the parts. Naturally they did, but the best part was that they had a video on how to change the part. The video was very clear and straightforward. So easy to follow. I ordered the part mid-day on a Thursday. Imagine my surprise when later that day an email came in letting me know that the part was already shipped! The next day the part was on my front... Read more

The part went on easily. U Tube video answered any questions I had before installing. Read more

Living in Texas it is hot all the time, even in fall, so our family loves our cold filtered water and ice. We woke up one morning with water all over the floor in the kitchen. It looked like it was coming from our freezer through the ice dispenser. We turned off the water shut off valve and removed what was now a giant block of ice instead of an ice dispenser from our freezer to melt in the sink. Since we have used AppliancePartsPros.com before, I knew exactly what I needed to do to see if we... Read more

Watched the attached video, then followed directions and installed the part ordered. Read more

I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more

• Little to no heat when baking
• Oven not heating evenly
• Won't start

Replaced lower and upper element. Internet research suggested it was the control board. Thankfully it was a much quicker and cheaper fix. Read more

• Shakes and moves

I called a repair guy who came out to specifically replace the suspension rods because I read that if you push down on the tub and it bounces around, then the rods have worn out. After running the diagnostics, the repair guy tried to tell me it was because the lid was not locking correctly! After expressing concern that this makes no sense, he continued taking things apart and noticed the agitator rollers were all broken and told me this is probably causing the tub to be unbalanced. I... Read more

• No heat or not enough heat
• Too hot

Since the dryer was 24 years old I opted to replace all the possible problem components, instead of just the bad one. The parts aren't that expensive and do to their age I figured it was worth it to avoid having to go back into the dryer in a few months. The repair was surprisingly easy and went pretty much as the video instruction AppliancePartPros provided with one exception. Because, my model was much older than that used in the video, I had a more difficult time replacing the Heating... Read more

• Will not drain
• Noisy
• Burning smell
• Pumps but will not spin

There was a loud noise from my washer during the drain cycle. (The washer seemed to drain just fine.) It was pretty easy to determine that the noise was coming from the drain pump. (Which for my washer is behind the front lower inspection panel on the right side front.) I inspected the outside of the pump for any physical damage and verified no issues with the pump or the mounts. Everything seemed ok. I then checked the drain pump filter(You will need something to catch water if you do... Read more