Need Help?
Call or text
Molded adapter plate that secures and seals spray system components in your dishwasher. Replace if cracked, warped, or broken to stop leaks.
My husband Read more
This dispenser water tube routes water from the inlet to the refrigerator's in-door dispenser manifold, helping ensure a steady, leak-free flow to the dispenser.
Replaced spray arms and tube. Found all had debris in them and prohibited water pressure from reaching items. After replacement everything comes out sparkling. Don't understand how the spray arms getting plugged. Almost like waste water is recycled. Turns out to be a very easy project and if needed AppliancePartsPro has information and directions available at your finger tips.! Read more
Mounts and secures the upper spray arm in your dishwasher tub. Replace if cracked, broken, or missing to restore proper spray arm positioning.
Replaced hub, gasket and spray arm Read more
Shock absorber that cushions vibrations during spin cycles. Mounts between the drum and base. Replace if cracked, leaking, or worn to restore stability.
Metal mounting plate that secures the microwave chassis to the wall or cabinet. Replace if bracket is bent, cracked, or missing during installation.
Called appliance parts pros and received the OEM bracket the next day. Fit perfectly. No problem. Read more
Secures the washer's inner basket to the drive hub, keeping the tub centered and stable during spin. Replace if cracked, corroded, or bolts are damaged.
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more
Secures the upper spray arm to the water feed. Replace if cracked, broken, or loose to restore proper arm alignment and rotation for the top rack.
Replaced all leaky parts including the wash arm that send water to the top rack. Most parts are just snap-in and one required a single screw. Very easy job. Read more
The Washer Flange Shaft Assembly is essential for maintaining the smooth operation of your Samsung washer. This assembly includes the flange shaft, designed to ensure proper alignment and stability during each wash cycle. Crafted from high-quality materials, the Washer Flange Shaft Assembly provides durability and reliable performance, extending the lifespan of your appliance. Installing this genuine OEM part guarantees a perfect fit and seamless integration with your Samsung washer model. With its robust construction, this part helps reduce noise and vibration, enhancing your laundry experience. Whether you're replacing a worn-out component or restoring your washer's functionality, the Washer Flange Shaft Assembly offers a dependable solution. Trust in this genuine OEM part to deliver consistent results and maintain the efficiency of your Samsung washer, ensuring your appliance operates like new.
Since the Tub is Stainless Steel and the Spider is an electrically inferior alloy, Galvanic corrosion will inevitably deteriorate the Spider/Flange to the point of failure. My solution was to bead blast and bake on an epoxy coating to the replacement Spider/Flange to minimize the bimetallic corrosion of this electrically inferior alloy since this is what Samsung is still utilizing. I found the video series done by AppliancePartsPros.com especially well crafted and is in fact why I chose to buy... Read more
The Shock Absorber is an OEM part compatible with Whirlpool washing machines. It is a crucial component that helps reduce vibrations and dampens movement during the spin cycle. The shock absorber absorbs mechanical stresses to prevent the washer tub, suspension springs, and other components from wearing out prematurely.
Causes of a bad shock absorber include wear and tear over time, cracks or breaks from heavy loads, or damage due to impact.
Symptoms of a bad shock absorber include:
This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Hinge component that guides the cam for self-closing door action. Replace if cracked, broken, or worn to restore smooth door swing and proper alignment.
Emptied the door, removed the top door hinge plate, removed the door, then removed the damaged lower hinge plate and bushing, and then replaced them with the new parts. Everything went back together just fine, and now the door closes properly, and stays closed! Thanks!! Read more
Secures the temperature sensor in place inside your dishwasher's sump area. Replace if the holder is cracked, broken, or missing to keep the thermistor properly positioned.
Followed the LG owner's manual instructions for cleaning the wash "arms". After that was complete the lower arm wouldn't operate. The filter assemble was caked with calcium, so decided to replace it and the lower spray arm and the "Holder" as your catalog described it. Removal and replacement were easy. The exploded parts diagrams on your website were very helpful. Read more
This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.
Refrigerator was easy. Simply replaced the activator switch that was sticking. The range hood was a little more difficult. I had replaced the switch years ago but it still didn’t work. So I took on the challenge of replacing the transformer. That was difficult to get to but once replaced and reassembled the lights work fine. Read more
Suspension damper shock absorber for front-load washers. Replaces cracked, weak, or broken shocks causing excessive vibration and off-balance loads.
I researched the problem and found that normal wear and tear will cause the Damper shocks and the Suspension spring to fail. I decided to replace all Damper Shocks and the suspension Springs since I had the washer apart already. The Suspension Spring requires a lot of pull to get it in place correctly. I made a hook tool (from political yard sign frame) to hook the old spring to remove and pull the new spring up. It helps to have a second person use leverage (use a short 2x2 board) under the... Read more
Anchors the door balance spring to the dishwasher frame. Replace this hanger if worn, broken, or missing to restore proper spring tension and support.
Found a great extensive list of available parts for our dishwasher model on the website. Reference to videos made the repair steps very clear and easy to follow. Read more
Replaces broken or worn washer shock absorber that controls tub movement during spin. Installs on washer suspension to reduce vibration and shaking.
I took the front panel off which exposed the front two shock absorbers. But I could still only replace the front left shock. I could not get access to the one on the right. I then took the back panel off which gave me access to both back shocks and the other front shock. A simple twist and they were done. The longest part of the job was taking the back panel off. Read more
Small structural block that secures and aligns the refrigerator or freezer handle to the door. Replace when cracked, broken, or missing to restore handle fit.
Found the Block on your website. I was happy I didn’t need to order the whole handlebar instead. Read more