Washer Dryer Combo Parts

Restore smooth, accurate cycle selection with this replacement timer knob for your dryer. When the original knob is cracked, stripped, or missing, this part lets you reliably set the timer and choose drying programs again. What it does:

• Attaches to the timer shaft so you can set drying cycles and time
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps resolve issues like the knob spinning freely or not turning the timer
• Provides a clean, factory look in white

• 1 white timer knob

• Disconnect power to the dryer before servicing
• Pull the old knob straight off the timer shaft; use steady, even pressure if tight
• Align the new knob with the keyed shaft and press firmly until fully seated
• The pointer aligns with the control panel cycle markings before use

Dryer won't turn off or advance cycles? This control timer regulates cycle progression and automatic shutoff. Moderate DIY repair restores timing.

Fix a washer that won't advance through cycles or gets stuck washing or spinning. This control timer regulates cycle progression. Moderate DIY repair.

This is the rear blower housing that encloses and supports the blower fan assembly in a combination washer/dryer unit. It directs airflow through the dryer section to ensure proper drying performance. Replace this housing if it is cracked, warped, or damaged, which can lead to poor drying, unusual noises, or restricted airflow during the dry cycle.

This plug covers an unused opening on the appliance cabinet or panel to restore a clean, finished look. Replacing a missing or damaged plug helps keep dust and lint out of the cabinet and can reduce vibration-related rattles. What it does:

• Covers an open hole on the cabinet or panel after service or manufacturing access
• Helps block dust and lint from entering the cabinet
• Restores appearance and can eliminate small buzzes/rattles from open gaps
• Replaces a lost, cracked, or loose plug

• One plug

• Disconnect power to the appliance; for washers, also turn off the water supply
• Align the plug with the opening and press or snap it in until fully seated and flush
• Before restoring power and use, ensure the plug is secure

The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.

• Directs and focuses airflow through the heat-exchange coils for proper operation
• Supports and aligns the blower wheel so it spins with correct clearance
• Helps minimize vibration and noise when the housing is intact
• Symptoms of a failed housing may include scraping or rattling noises, weak airflow, vibration, or visible cracks/broken mounts around the blower area

• Disconnect power before servicing; wear cut-resistant gloves and eye protection.
• Remove the front panel/cabinet to access the blower section; note screw and clip locations.
• Transfer the blower wheel, seals, and any reusable hardware from the old housing.
• Before reassembly, spin the blower wheel by hand to ensure free, rub-free rotation.

Keep your dryer drum turning smoothly. This idler & pulley assembly maintains proper tension on the drive belt so the drum rotates quietly and efficiently when the original idler or pulley becomes worn, noisy, or seized. What it does:

• Applies spring-loaded tension to the drive belt for consistent drum rotation
• Provides a smooth rolling surface to minimize belt friction and wear
• Worn/failed parts may cause squealing or chirping, the drum not turning, the belt slipping off or breaking, or a hot rubber smell

• One idler and pulley assembly

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the belt path by removing the necessary panels per your service information
• Pull the idler to release belt tension, remove the old assembly, install the new one, and route the belt correctly around the motor and idler
• Manually rotate the drum to verify belt tracking before reassembly and test run

Dryer not heating or taking too long to dry? This heating element generates heat to dry clothes. Common repair for no heat issues in laundry centers.

Dryer drive belt connects the motor to the drum for smooth tumbling. Replace when stretched, broken, or causing slipping noises. Confirm fit with your model.

Fix a dryer that won't start, won't advance cycles, or has a smoking timer. This control timer restores proper cycle operation. DIY repair in 1 hour.

Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.

Captures lint and fibers during drying to prevent vent clogs. Replace when torn, damaged, or screen detaches from frame. Confirm fit with your model.

This control knob assembly lets you select cycles and settings on your dryer. Replacing a cracked or stripped knob restores firm engagement with the timer or selector so you can set, start, and adjust drying reliably.

• Attaches to the control shaft to turn the timer or selector
• Provides a secure grip and pointer to choose cycles and options
• Restores proper control when the original knob is cracked or the hub is stripped
• Typical symptoms: knob spins without turning the shaft, feels loose, falls off, or is missing

• Disconnect power to the dryer before servicing
• Pull the old knob straight off; note the shaft shape and orientation
• Align the new knob with the flat/D-shaft and press until fully seated
• If your model uses a separate dial ring or clip, transfer it from the original

This spring cover protects and retains a mechanism spring inside your washer. Replacing a cracked or missing cover helps keep the spring seated, limits debris intrusion, and supports smooth, reliable movement of the associated control, latch, or linkage.

• Shields the spring and helps keep it properly seated in its pocket
• Reduces friction and wear that can lead to premature spring failure
• Supports consistent return action for the related control, latch, or lever
• Typical symptoms include a missing/broken cover, exposed spring, rattling, or erratic operation

• Unplug the appliance and turn off water before servicing
• Access point varies by model; photograph spring/cover orientation before removal
• Control the spring during disassembly to prevent sudden release
• Ensure the cover is fully seated; test operation before final reassembly

Replacement drain hose for washers. Routes wastewater from the drain pump to your household drain. Replace if cracked, leaking, clogged, or worn.

Washer won't start or advance to spin cycle? A broken lid strike prevents the lock from engaging. Simple 5-minute snap-in fix—just remove two screws.