Washer Dryer Combo Parts

This transmission and support assembly drives and stabilizes the wash basket. It converts motor power into agitation and spin while supporting the tub, helping resolve no-agitate/no-spin complaints and loud operation for reliable cleaning performance.

• Transfers motor power to the drive system for agitation and spin
• Supports the basket and helps maintain alignment during operation
• Helps correct no agitate, no spin, or weak/intermittent spin
• Can address grinding/rumbling noises or oil traces from the center

• Disconnect power and water before servicing; wear gloves and eye protection
• Appliance and assembly are heavy—use assistance and protect flooring
• Removal typically requires accessing from top and bottom to remove agitator/basket and drive hardware
• After installation, run a test cycle to ensure smooth agitation, proper spin, and no leaks

Front suspension rod assembly that supports and stabilizes the washer tub. Replace if rod is bent, damaged, or worn to restore proper tub alignment.

This is a high limit thermostat that monitors the temperature inside the dryer's heating chamber and shuts off the heating element if temperatures exceed a safe threshold. It serves as a safety device to prevent overheating and potential fire hazards. Replace this thermostat if your dryer is not heating at all, shuts off prematurely, or if a multimeter test shows no continuity through the thermostat.

Fix a laundry center that won't spin, agitate, or hums without moving. This drive motor replacement requires moderate skill and 2-3 hours to install.

Secures components inside your washer to prevent movement, loose connections, and rattling noise. Replace when worn or missing to restore stability.

Rear suspension rod assembly that supports and stabilizes the washer tub from the back of the cabinet. Replace if worn, broken, or cracked to restore balance.

Burner orifice that meters gas flow to your dryer's burner. Replace if clogged, damaged, or wrong size for fuel type during LP/natural gas conversion.

Captures lint and fibers during drying to prevent vent clogs. Replace when torn, damaged, or screen detaches from frame. Confirm fit with your model.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This control knob assembly lets you select cycles and settings on your dryer. Replacing a cracked or stripped knob restores firm engagement with the timer or selector so you can set, start, and adjust drying reliably.

• Attaches to the control shaft to turn the timer or selector
• Provides a secure grip and pointer to choose cycles and options
• Restores proper control when the original knob is cracked or the hub is stripped
• Typical symptoms: knob spins without turning the shaft, feels loose, falls off, or is missing

• Disconnect power to the dryer before servicing
• Pull the old knob straight off; note the shaft shape and orientation
• Align the new knob with the flat/D-shaft and press until fully seated
• If your model uses a separate dial ring or clip, transfer it from the original

Restore smooth, accurate cycle selection with this replacement timer knob for your dryer. When the original knob is cracked, stripped, or missing, this part lets you reliably set the timer and choose drying programs again. What it does:

• Attaches to the timer shaft so you can set drying cycles and time
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps resolve issues like the knob spinning freely or not turning the timer
• Provides a clean, factory look in white

• 1 white timer knob

• Disconnect power to the dryer before servicing
• Pull the old knob straight off the timer shaft; use steady, even pressure if tight
• Align the new knob with the keyed shaft and press firmly until fully seated
• The pointer aligns with the control panel cycle markings before use

Fix a washer that won't advance through cycles or gets stuck washing or spinning. This control timer regulates cycle progression. Moderate DIY repair.

This plug covers an unused opening on the appliance cabinet or panel to restore a clean, finished look. Replacing a missing or damaged plug helps keep dust and lint out of the cabinet and can reduce vibration-related rattles. What it does:

• Covers an open hole on the cabinet or panel after service or manufacturing access
• Helps block dust and lint from entering the cabinet
• Restores appearance and can eliminate small buzzes/rattles from open gaps
• Replaces a lost, cracked, or loose plug

• One plug

• Disconnect power to the appliance; for washers, also turn off the water supply
• Align the plug with the opening and press or snap it in until fully seated and flush
• Before restoring power and use, ensure the plug is secure

Secures the spider assembly to the inner drum in your washer. Replace if bolt is stripped, loose, or missing to restore secure mounting and reduce noise.

Keep your dryer drum turning smoothly. This idler & pulley assembly maintains proper tension on the drive belt so the drum rotates quietly and efficiently when the original idler or pulley becomes worn, noisy, or seized. What it does:

• Applies spring-loaded tension to the drive belt for consistent drum rotation
• Provides a smooth rolling surface to minimize belt friction and wear
• Worn/failed parts may cause squealing or chirping, the drum not turning, the belt slipping off or breaking, or a hot rubber smell

• One idler and pulley assembly

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the belt path by removing the necessary panels per your service information
• Pull the idler to release belt tension, remove the old assembly, install the new one, and route the belt correctly around the motor and idler
• Manually rotate the drum to verify belt tracking before reassembly and test run