Washer Valve

Replaced the cold water valve unit (has 4 ports and 1 inlet) which is very straight forward; requires : 1 phillips screwdriver ~#2 1 needlenose plier, medium size 1 channel lock plier, medium size 1 marker pen 1 - cold water valve assembly # AP4445613 1 - hot water valve assembly #AP4441935 1 - water level pressure switch #AP4440713 an old towel or two for absorbing small amounts of water a cellphone / camera for making sure you have the... Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water

I ordered the valve from Appliance Parts--it arrived promptly. I replaced the faulty valve with the new valve and now washer works like new. Read more

• No hot or cold water
• Will not stop filling with water

I unplugged the machine. I removed the two fill hoses. I removed the top of the washer case by removing 3 tamper proof screws from the back ( I used my set of "star" head drivers), sliding the top back 1 inch and lifting the top off. I marked the 4 wires with 1 thru 4 stripes with a marker for ID, then pulled the 4 wires off the landing terminals. I removed the mounting screw and lifted the valve up as far as the hose permitted to get a better grip on the valve and hose. I removed the... Read more

I replaced both the solenoid (part of the inlet valve kit) and the pressure sensor. Online research suggested my intermittent issue with the cold water fill being just a trickle and then causing an error was likely due to one or both of those two parts failing. Since they are in the same spot it was suggested (and I agree) that it is best to replace both at the same time. The hardest and most frustrating part was getting the bracket back on with the two bottom tabs being in place. It took... Read more

Installed new Water Inlet Valve. Read more

GE Top Loading Washer, slow drip leak from top of tub when off; ordered triple water valve. Removed 3 hex screws behind top control panel (in back); removed 2 rear hex screws on back of control panel. Removed hoses and plug. As you move panel forward, its lower tabs slide sideways in order to remove/roll panel forward. Unplug hot and cold wire harness leads. Unscrew 2 Phillips head screws. Removed hose clamp--BE CAREFUL--as you remove the hard plastic hose from the Triple Valve. Removed... Read more

Replaced water mixing valve. Read more

After tracing the water dripping back up through the inside of the washer I found the water dispenser inlet valve was leaking. I watched several videos to make sure I understood what was involved. I contacted a local parts company to get the part. I also searched online for the part. I found that AppliancePartsPros.com had it cheaper. I ordered late in the afternoon and it arrived the next day. It was fairly easy to installed and saved me a minimum of $99 "diagnostic" fee plus whatever the part... Read more

• Will not fill with water
• Will not stop filling with water

This should be plastered all over the place and every owner of a front end washer should be advised or a recall should be issued about this. As I opened the top of my washer to fix a F35 error by replacing the water level switch, which worked out great and it fixed the issue, I noticed a rusting spot at the bottom of the washer just under where the motor is placed. After running the washer with the lid open (I don't recommend doing that) I noticed that it was coming from the top of the soap... Read more

Replaced water inlet valve took all of 10 minutes and washer is filling great on hot and cold. Thanks to Appliance Parts Pros for getting me the part within 24 hours. I have a very happy customer. Read more

I found a youtube video about replacing the hot water valve in a Samsung washer. It looked pretty easy. I had been very satisfied with an earlier order from AppliancePartsPros.com, so I ordered this part on Sunday after 9PM, standard delivery, hoping to get the part by the end of the week. I was flabbergasted to receive the part TUESDAY MORNING! Wow! I followed the instructions in the youtube video exactly. It took around 15 minutes, because I was being very careful not to drop screws in... Read more

• No hot or cold water
• Will not stop filling with water

It was really easy to fix. I just took a screw driver and gently pried up on the top of the clothes washer to open up the top. Then the mixing valve was easy to access. I removed the two screws holding and unplugged the the wires. And pulled the old one free. Then reversed the process to install the old one. Less than thirty minutes start to finish. Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

Replaced both hot and cold water inlet valves. Works like a charm, issue resolved. Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water
• Noisy

1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more

Replaced valve assembly- issue resolved. super easy to replace the part Read more