General Electric Axle, Roller, Pulley Parts

Replace cracked or worn upper rack rollers that prevent smooth sliding. Kit includes studs and wheels for secure rack gliding. Fits GE dishwashers.

Drive pulley mounts to the washer basket shaft and routes the belt from the motor. Replace if worn, cracked, loose, or showing play on the shaft.

White dishwasher lower rack roller axle. Replaces broken or worn axles that cause wheels to fall off. Snap-in design for easy installation.

Includes screws.

Idler arm assembly mounts to the dryer frame and maintains proper belt tension on the drum. Replace if the arm is cracked, bent, or the pulley is worn.

This float stem is part of the dishwasher's water-level/overfill system. It guides the tub float and actuates the float switch so the unit fills correctly and shuts off on time. Replace a worn or broken stem to restore reliable fill protection.

• Connects the float to the switch mechanism beneath the tub
• Provides smooth vertical travel of the float through the opening
• Triggers the float switch to stop filling at the proper level
• Causes symptoms such as no fill, continuous filling/overfilling, a stuck or wobbly float, or intermittent fill issues

• Disconnect power at the breaker and shut off the water supply before servicing
• Remove the lower rack; lift off the float cap from inside the tub
• On some models, release the retainer/clip from beneath the tub; pull out the old stem
• Guide the new stem through the opening and ensure it engages the float switch lever; confirm the float moves freely and actuates the switch before restoring power

Keep your dryer drum turning smoothly. This idler & pulley assembly maintains proper tension on the drive belt so the drum rotates quietly and efficiently when the original idler or pulley becomes worn, noisy, or seized. What it does:

• Applies spring-loaded tension to the drive belt for consistent drum rotation
• Provides a smooth rolling surface to minimize belt friction and wear
• Worn/failed parts may cause squealing or chirping, the drum not turning, the belt slipping off or breaking, or a hot rubber smell

• One idler and pulley assembly

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the belt path by removing the necessary panels per your service information
• Pull the idler to release belt tension, remove the old assembly, install the new one, and route the belt correctly around the motor and idler
• Manually rotate the drum to verify belt tracking before reassembly and test run

Supports and centers the dishwasher spray arm for smooth rotation. Replace if worn, cracked, or causing wobbling. Installs under spray arm hub.

Lower rack roller and stud assembly for dishwashers. Mounts to the bottom rack to allow smooth sliding in and out. Replace if broken, cracked, or missing.

Replace your dishwasher's lower rack wheel if it's cracked, broken, or worn. This roller ensures smooth gliding of the bottom rack during loading and unloading.

White plastic roller wheel for dishwasher lower rack. Replaces worn, cracked, or broken wheels that prevent smooth rack gliding. Sold individually.

Upper rack roller wheel for dishwashers. Mounts on the upper dish rack to enable smooth rolling on side rails. Replace if cracked, broken, or worn out.

Drum roller assembly for dryers. Mounts to the rear panel to support smooth drum rotation. Replace if worn, squeaking, cracked, or causing wobble.

Replace a worn, broken, or damaged dryer idler arm. This structural part holds and tensions the belt around the motor pulley and drum in your dryer.

Replacement idler spring for dryer belt tensioning system. Installs on idler pulley assembly. Replace if stretched, broken, or missing to restore tension.

This roller support holds the dryer drum roller in place to help the drum turn smoothly and stay aligned. Replacing a worn support can reduce noise and wobble and help protect the belt and drum from uneven wear. What it does:

• Holds and positions the drum roller so the drum rotates with minimal friction
• Keeps drum alignment and belt tracking stable during operation
• Helps prevent drum wobble and uneven wear that can lead to rubbing or thumping noises
• Common symptoms: loud squealing or grinding, thumping during rotation, visible drum wobble

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer front or rear panel; follow the model's service manual
• Inspect the roller, axle, and adjacent support components; replace any worn parts to prevent repeat failure
• Use proper tools and secure fasteners to factory torque