General Electric Dispenser Parts

This junction box cover replaces the appliance's electrical access panel to protect wiring and provide a secure entry point for the power cord. It restores a finished, safe electrical connection area and helps prevent exposed wiring. What it does

• Covers and protects the appliance's electrical junction box from dust and accidental contact
• Provides the mounting location and opening for the power cord/strain-relief connection
• Secures wiring and helps keep wire connections contained and stable
• Common symptom: cover cracked, missing, or loose—exposed wires or inability to secure the power cord

• Disconnect power at the breaker or unplug the appliance before servicing electrical parts
• Remove mounting screws from the old cover and replace with the new cover; retain or replace strain relief as needed
• Inspect the cord and wiring while access is open; replace any damaged wiring or strain relief components
• Follow the appliance manufacturer's instructions and local electrical codes for safe installation

This liquid detergent insert fits into the washer's dispenser to meter and release liquid detergent at the correct time. Replacing a missing or damaged insert helps prevent early drain-off and supports consistent cleaning performance.

• Adapts the main detergent compartment for use with liquid detergent
• Helps control flow so detergent releases during the wash cycle, not immediately
• Promotes proper dispensing and reduces residue left in the dispenser
• Common clues it's needed: insert missing/broken, liquid runs straight into the tub, or detergent remains in the cup after a cycle

• Disconnect power to the washer before servicing
• Pull out the dispenser, then lift out the old insert
• Align and press the new insert into the detergent compartment until fully seated (follow any "LIQUID"/fill marks)
• Run a quick test cycle to ensure proper dispensing

This drawer dispenser assembly replaces a damaged or worn dispenser drawer to restore secure containment and reliable dispensing in your appliance. It helps keep detergents or dispensing components properly housed and prevents leaks or jams. What it does:

• Holds the appliance's dispenser drawer securely in place during use
• Guides and releases detergent or dispensing materials as designed
• Stops leaks or drips caused by cracked, warped, or broken drawer parts
• Prevents binding or sticking of the dispenser drawer for smooth operation

• Disconnect power and water before beginning any repair
• Remove the drawer or access panel per the appliance service instructions before installing
• Handle plastic components carefully to avoid cracking; use appropriate tools and gentle force

This latch cover insert replaces a worn or broken door latch trim so the appliance door closes cleanly and looks finished. It restores a secure, aligned latch area and improves door appearance. What it does:

• Covers and protects the door latch mechanism from dirt and damage
• Provides a smooth surface for the door to engage the latch properly
• Helps prevent rattling or misalignment caused by a damaged trim
• Matches the original finish for a factory look

• Remove power to the appliance before beginning any work
• Typically snaps or screws into place; retain original fasteners if present
• Inspect surrounding latch components and replace if damaged

The Liquid Detergent Insert is an OEM part for GE washing machines. It is a small but important compartment that holds and dispenses precisely dosed amounts of liquid detergent during cycles. Located inside the detergent dispenser drawer, the liquid insert helps ensure the correct concentration of detergent is released. 

Causes of a bad liquid detergent insert can include cracked or broken plastic from repeated use, hardened plastic that no longer flexes properly to release detergent or damage to dispenser shutter mechanisms that control flow.

Symptoms of a bad liquid detergent insert include:

• Improper or uneven dispensing of detergent into the wash  
• Over or under-sudsing due to too much or too little detergent
• Residual detergent left in the insert compartment
• Reduced cleaning ability due to incorrect dosing

This genuine GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This cap tower upper is the replacement cover piece for the top of the dispenser/tower assembly. It restores the finished fit and alignment of the tower so the dispenser components sit correctly and look complete. What it does

• Covers and protects the top section of the tower/dispenser assembly to keep internal components shielded.
• Restores the correct appearance and alignment of the dispenser area after damage or wear.
• Helps prevent debris from entering the tower opening and interfering with nearby parts.
• Commonly replaced when cracked, broken, chipped, or missing, or when the tower no longer seats properly.

• One cap tower upper.

• Disconnect power to the appliance before beginning any repair.
• This part typically snaps or fits into the tower; inspect surrounding clips or tabs for damage before installing.
• Handle plastic tabs carefully to avoid further breakage; replace any damaged mounting clips.

This replacement bleach dispenser insert fits into the washer's bleach drawer to hold and release liquid bleach during the wash cycle, helping ensure proper dilution and safer delivery to the drum. What it does:

• Holds liquid bleach in the dispenser so it releases at the correct point in the cycle
• Directs bleach into the wash water to reduce concentrated contact with fabrics
• Prevents bleach from pooling or spilling inside the drawer
• Helps avoid uneven bleaching and fabric spotting when functioning correctly

• Disconnect power to the appliance before servicing
• Remove the dispenser drawer per the washer's service instructions, then lift out the old insert and snap the new insert into place
• Handle bleach residue with gloves and rinse parts thoroughly after installation
• Replace the whole dispenser assembly if the dispenser assembly is cracked or the insert won't seat properly

Color: blue-gray. It measures about 1-1/2 inches in diameter.

This dishwasher detergent dispenser assembly stores detergent and releases it at the correct time in the wash cycle to ensure consistent cleaning results. Replacing a worn dispenser restores reliable soap release and helps improve wash performance.

• Holds detergent and opens when signaled by the control
• Common symptoms: detergent cup won't open, soap left in the cup after cycle, broken dispenser door/latch

• Disconnect power to the dishwasher before servicing
• Open the door and remove inner-door screws to access the dispenser
• Release locking tabs, remove the old dispenser, and clean the sealing surface
• Seat the new dispenser evenly, reinstall screws, restore power, and run a test cycle

This dishwasher vent cover mounts on the inner door and shields the exhaust opening. It directs moist air out during drying while helping keep spray and debris out of the vent path to protect internal components. What it does:

• Covers the door vent opening and helps guide exhaust airflow during the dry cycle
• Helps keep water spray and debris from entering the vent assembly
• Supports proper moisture management around the top of the door/control area
• Replace if the cover is cracked, warped, loose, or missing, or if steam/water escapes from the vent area

• 1 vent cover

• Disconnect power at the breaker and turn off the water supply; wear cut-resistant gloves
• Access is through the door; on many models the inner door panel must be removed to reach the vent area
• Ensure any gasket/seal is properly seated and secure the cover evenly—do not overtighten
• Run a short cycle and inspect the vent area for leaks

This middle spray arm bracket secures the mid-level spray arm to the upper rack, keeping it centered and aligned so it spins freely and delivers even spray coverage for reliable cleaning performance.

• Supports and stabilizes the middle spray arm beneath the upper rack
• Maintains proper clearance for smooth rotation and spray pattern
• Replace if cracked, warped, or worn
• Common symptoms: middle arm falls off or won't spin, wobbles, scraping noises, or poor cleaning on the upper rack

• Disconnect power to the dishwasher before servicing
• Slide out the upper rack; release tabs or fasteners to remove the old bracket
• Transfer the spray arm to the new bracket and snap or secure it in place
• Spin the arm by hand to ensure free rotation before running a cycle

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

This upper dispenser trim—commonly called the top tower—replaces the visible upper cover at the refrigerator dispenser area to restore appearance and proper fit. It protects internal dispenser components and keeps the dispenser edges clean and aligned. What it does

• Covers and protects the upper portion of the dispenser tower and its internal components
• Helps maintain a consistent, finished look at the dispenser opening
• Prevents dirt and moisture from reaching internal dispenser parts
• Can reduce rubbing or misalignment of the dispenser fixture that can cause noise or wear

• One upper dispenser trim (top tower) as shown

• Remove power to the appliance before starting work to avoid electrical hazards
• Typically secures with clips or a few screws—gentle prying with a trim tool may be required
• Inspect adjacent trim and fasteners for wear and replace as needed for a proper fit