General Electric Heating Element

If your glass cooktop burner won't heat or is visibly damaged, this 9 inch dual radiant element restores cooking performance. DIY repair in 15-30 minutes.

This broil shield is the oven's rear cavity panel that protects the oven back and nearby components from direct broiler heat. It helps channel heat for safer broiling and prevents heat damage to internal parts. What it does:

• Deflects direct broiler heat away from the oven back wall and components
• Helps maintain proper broiling performance by directing heat toward food
• Reduces risk of heat-related damage, discoloration, or premature wear on internal oven parts
• Limits grease and debris contact with sensitive rear components

• Disconnect power (and gas supply on gas ovens) before servicing the oven
• Remove oven racks and, if required, the broil element to access the shield
• Handle edges carefully—metal parts can be sharp
• Keep hardware removed during disassembly; screw locations for reassembly

Oven not heating or baking unevenly? This bake heating element restores proper temperature for cooking and browning. Moderate DIY repair.

Cooktop not heating evenly or at all? This dual radiant surface element restores powerful heating across two zones. Direct replacement, moderate DIY.

Fix a warming drawer that won't heat with this low-temperature heating element. Restores gentle, consistent warming performance for cooked food in ranges.

Oven not heating evenly or taking too long to preheat? This hidden bake element restores consistent bottom heat for baking and roasting in electric ranges.

Oven not heating properly or broiler not working? This broil heating element restores even high-heat cooking. Common DIY repair, typically installs in 30-45 minutes.

This heating element assembly supplies heat for tumble drying, restoring warm airflow so clothes dry efficiently. It replaces a failed or burned element to help return normal drying performance. What it does:

• Generates the hot air used to dry clothes by heating incoming air that circulates through the drum
• Commonly replaces a burned-out or open element that causes no heat or reduced heat
• Helps address symptoms like cool air from the dryer, extended dry times, or loads that never fully dry
• Works with the dryer's safety thermostats and fuses to regulate operating temperature

• Heating element assembly (1)

• Disconnect power at the breaker or unplug the dryer before starting any repair
• Allow all components to cool and wear gloves to avoid sharp edges
• Basic hand tools are typically required; follow the dryer's service manual for safe removal and reassembly
• If the dryer still has heating issues after replacement, inspect thermostats, thermal fuses, and wiring

The oven control and overlay assembly are installed directly in the front of the main console of the oven. They contain the control interface of the appliance. When the overlay assembly and control interface malfunction, normally, the backlight goes out behind the console. The user is unable to see any controls or function information. This malfunction can be caused by electrical short or external damage. It's possible a fuse could be the problem, and a voltage tester can give you a clear indication of where the problem lies. Begin the installation by unplugging the oven first. Using a screwdriver, unthread the screws around the perimeter of the main user interface. This will allow the casing around the console to come off. On the rear of the oven, remove the screws holding the back panel in place until the control board can be seen. Unscrew the control board assembly from the control overlay assembly. Repeat these steps in reverse with the new part.This GE oven control and overlay assembly is a genuine OEM product sourced directly from the manufacturer. The listed product is sold individually. This part is compatible with GE, Kenmore, HotPoint, RCA, and Kenmore.

Replace a cooktop burner element that won't heat or heats unevenly. Common fix for non-working burners. Moderate DIY repair, 30-45 minutes.

Fixes cooktop burner that won't heat or heats unevenly. This radiant element sits under smooth glass and restores direct heat to cookware on electric ranges.

Burner won't heat or heats unevenly? This rear heating element restores proper cooking temperature. Moderate DIY repair with basic tools in 30-45 minutes.