General Electric Heating Element

This broil unit is the upper-oven heating assembly that provides direct high heat for broiling, browning and finishing dishes. Replaces a worn or failed broil element to restore proper broil performance. What it does:

• Produces the direct radiant heat used for broiling and browning food
• Replaces a visibly burnt, broken, or non-heating broil element
• Helps correct uneven browning or lack of upper-oven heat during broil cycles
• Works as the main heat source for the oven's broil function

• One broil unit assembly

• Disconnect power to the appliance at the breaker or unplug before servicing
• Allow the oven to cool completely; use gloves to protect hands from sharp edges
• Remove oven racks and access panel as required to reach the broil element
• Verify proper operation after installation

Note: 6" surface element

The Surface Dual Radiant Element 9" is an OEM part for GE electric ranges. This element is responsible for heating cooking vessels placed directly on the glass cooktop surface.

Causes of a bad element can include burns or damage from accidental contact with metal utensils, prolonged exposure to high heat, or failure of the electrical mechanism over time.

Symptoms of a bad element include:

• Slow or inconsistent heating
• Element not heating at all
• Burn or crack marks visible on the glass surface
• Buzzing or popping noises coming from below the cooktop

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This broil shield is the oven's rear cavity panel that protects the oven back and nearby components from direct broiler heat. It helps channel heat for safer broiling and prevents heat damage to internal parts. What it does:

• Deflects direct broiler heat away from the oven back wall and components
• Helps maintain proper broiling performance by directing heat toward food
• Reduces risk of heat-related damage, discoloration, or premature wear on internal oven parts
• Limits grease and debris contact with sensitive rear components

• Disconnect power (and gas supply on gas ovens) before servicing the oven
• Remove oven racks and, if required, the broil element to access the shield
• Handle edges carefully—metal parts can be sharp
• Keep hardware removed during disassembly; screw locations for reassembly

This hidden bake element provides the oven's primary lower heating source for baking and roasting. It restores consistent bake heat and is a direct-replacement part used in many GE electric ranges and wall ovens. What it does:

• Heats the oven cavity from the bottom for baking and roasting cycles
• Replaces a burnt-out or non-heating lower element to restore oven temperature
• Helps improve evenness of baking when the original element no longer reaches set temperature
• Commonly used when the oven won't bake or the lower area doesn't get hot

• One hidden bake heating element

• Disconnect power at the breaker or appliance plug before starting any work
• Allow the oven to cool completely and remove oven racks before accessing the element
• Element typically secures with mounting screws and two electrical terminals; support the element while removing/replacing to avoid stress on wires
• After installation, restore power and run a short bake cycle to verify operation

This lower bake element assembly heats the oven cavity for baking and roasting so you can cook food evenly. It replaces a damaged or failed lower heating element to restore normal oven heating performance. What it does:

• Produces the oven's lower radiant heat used during bake cycles
• Common fix when the oven won't reach or hold set temperature
• Replaces elements that are visibly burned, broken, or arcing
• Helps correct uneven baking when the lower element is not working

• Disconnect power to the appliance at the circuit breaker before servicing
• Allow the oven to cool completely; handle the element carefully to avoid damage
• Inspect wiring and connectors for heat damage and secure connections during installation
• After installation, restore power and run a short bake cycle to verify correct operation

The oven control and overlay assembly are installed directly in the front of the main console of the oven. They contain the control interface of the appliance. When the overlay assembly and control interface malfunction, normally, the backlight goes out behind the console. The user is unable to see any controls or function information. This malfunction can be caused by electrical short or external damage. It's possible a fuse could be the problem, and a voltage tester can give you a clear indication of where the problem lies. Begin the installation by unplugging the oven first. Using a screwdriver, unthread the screws around the perimeter of the main user interface. This will allow the casing around the console to come off. On the rear of the oven, remove the screws holding the back panel in place until the control board can be seen. Unscrew the control board assembly from the control overlay assembly. Repeat these steps in reverse with the new part.This GE oven control and overlay assembly is a genuine OEM product sourced directly from the manufacturer. The listed product is sold individually. This part is compatible with GE, Kenmore, HotPoint, RCA, and Kenmore.

This genuine dryer heater assembly heats the air inside the dryer so clothes dry efficiently. It replaces a failed heating element to restore normal drying performance and reduce extended drying cycles. What it does:

• Generates the heat required for the dryer to remove moisture from laundry.
• Restores normal drying times when a worn or broken element causes little or no heat.
• Works with the dryer's thermal controls to maintain safe operating temperatures.
• Can stop dryer trips or error conditions caused by an open or shorted element.

• One dryer heater assembly (heating element)

• Disconnect electrical power to the dryer before beginning any work.
• Handle the element carefully — avoid bending or contacting the coil with sharp tools.
• Inspect and, if necessary, test the thermal fuse, thermostats, and wiring; replace any failed safety components.