General Electric Manual, Care Guide

This printed PM service manual provides official service and maintenance procedures to help technicians diagnose and repair affected GE appliances. It helps technicians follow OEM-recommended steps for safe, accurate troubleshooting and parts replacement. What it does:

• Provides step-by-step service procedures, wiring diagrams, and component locations for covered models
• Helps identify troubleshooting tests and common symptoms leading to repair
• Clarifies parts identification and assembly/disassembly sequences for service tasks
• Supports correct replacement of components by showing proper routing, connections, and adjustments

• This is a service/manual reference — no electrical components are included.
• Use this manual only when qualified to service appliances; follow all safety warnings and lockout/tagout procedures.
• Always disconnect power and water before servicing equipment.
• For model-specific procedures, follow the manual's applicable section.

This printed PM manual provides official preventive maintenance and basic service guidance for compatible GE appliances, helping technicians and experienced DIYers follow recommended checks and adjustments. It clarifies routine inspection steps to keep equipment operating reliably. What it does:

• Describes routine preventive maintenance procedures and recommended service checks
• Summarizes common symptoms that indicate maintenance is needed
• Helps guide safe diagnostics and routine adjustments during service visits
• Provides reference information technicians use during scheduled maintenance

• Review the manual fully before performing any service or maintenance
• Always disconnect power and water to the appliance before servicing
• Follow all safety warnings and use proper tools and PPE; for complex repairs
• This manual is a reference document—it does not include replacement parts

This is the appliance wiring diagram/schematic — a paper schematic that shows the electrical layout and component wiring for technicians and owners. It helps identify circuits and wire routing for diagnostics and repairs. What it does:

• Shows the appliance's electrical circuits, components, and wire connections for accurate troubleshooting
• Helps locate and trace wires, terminals, switches, and harnesses during repairs
• Useful when the original diagram is missing, torn, or illegible
• Supports correct reassembly after service by showing factory wiring routes

• One wiring diagram/schematic (paper)

• Not an electrical component; refer to the diagram while the appliance is powered off
• Disconnect power to the appliance before using the diagram to plan electrical work
• Replace or store the diagram in the appliance console or service area to keep it accessible

This wiring schematic is the OEM electrical diagram that shows appliance wiring layout and connections to help identify circuits and wiring paths for troubleshooting. It clarifies component locations and wire colors for accurate diagnostics. What it does:

• Shows the appliance's electrical wiring layout and connection points for components and terminals
• Identifies wire colors, harness routing, and terminal labels to aid diagnosis of power, control, or grounding issues
• Helps locate shorts, open circuits, and incorrect connections when symptoms include no power, intermittent operation, or blown fuses/breakers
• Provides a reference for technicians to verify correct wiring during repairs or after component replacement

• One printed wiring schematic/diagram as shown

• This is a reference document; no electrical wiring is repaired by replacing the diagram itself
• Always disconnect power to the appliance before testing or working on electrical components
• Keep the schematic clean and dry; store with the appliance documentation for future service

This wiring schematic is the factory service diagram used to identify electrical circuits and component connections for troubleshooting and repairs. It helps technicians and DIYers trace wiring paths and proper connections during diagnosis. What it does:

• Shows the appliance's electrical circuits and component wiring layout
• Helps locate connectors, wire colors, and terminal designations for testing
• Aids in diagnosing electrical faults such as no power to a component or intermittent operation
• Useful reference when replacing components or harness connections

• Intended as a reference document only; follow factory instructions and wiring diagrams during repairs
• Turn off power to the appliance before performing any electrical tests or repairs
• Keep the schematic dry and flat to preserve legibility

This printed PM installation sheet provides step-by-step OEM guidance to help properly install and maintain the appliance. Clear instructions reduce guesswork and help ensure correct setup and routine checks. What it does:

• Describes required steps for installation-related preventive maintenance tasks
• Lists recommended checks and adjustments to keep the appliance operating as intended
• Highlights safety cautions and basic troubleshooting tips for common service situations
• Helps homeowners follow OEM-recommended procedures during service

• Read the entire instruction sheet before beginning any work
• Disconnect power and water before performing maintenance
• Follow all safety warnings and use appropriate personal protective equipment
• Retain the instruction sheet with the appliance for future reference