General Electric Pump

Dishwasher won't drain or leaks at the base? A cracked or clogged sump inlet blocks water flow from the tub. Easy 30-minute fix with video guide.

Dishwasher leaking from underneath? A cracked or warped inlet sump channels water improperly. Direct DIY repair, typically done in 30 minutes.

Dishwasher not draining or water pooling at the bottom? A faulty drain pump is often the cause. This pump removes wastewater efficiently. DIY-friendly repair.

Fix a washer that won't drain or leaves water after the cycle with this drain pump assembly. DIY-friendly repair—turn washer upside down for easier access.

This pump and brake assembly drains water from the tub and applies the basket brake in your top-load washer. Replacing a worn assembly restores proper draining and a safe, prompt basket stop between cycles. What it does

• Pumps water out of the washer during drain and spin phases
• Applies the brake to stop the spin basket between cycles or when the lid switch is activated
• Helps reduce extended coast-down and stopping squeal
• Typical symptoms: standing water, slow/no drain, leaking at the pump area, basket coasts too long or squeals when stopping

• One pump and brake assembly

• Disconnect power and water supply; drain remaining water from hoses before service
• Access from the washer's underside; support the unit securely
• Transfer existing hoses/clamps to the new pump and secure all connections; if belt-driven, verify proper belt routing and pulley alignment
• Run a brief fill/drain test and recheck for leaks and proper basket stop

The DRAIN PUMP is an OEM component specifically designed for GE washers. It is located near the base of the unit and functions to remove water from the wash tub at the end of cycles. The drain pump works vigorously to expel soiled water through the drain hose for hygienic cleaning.  

Symptoms of a bad drain pump include:

• Water remaining in the tub even after cycles have finished running  
• Drain hose that is not effectively carrying away water
• Strange gurgling or churning noises coming from below the unit
• Possible leakage from seals or connections near the drain area

Causes can include internal blockages from built-up debris, wearing of impeller seals or motor, or physical damage impairing pump functionality.

Replace yours today with this genuine OEM GE part for thorough water extraction and machine drainage after every load. This GE replacement part is compatible with Hotpoint, RCA, and select Kenmore models.

Grinding noise during drying cycle? This vent door actuator opens and closes the dishwasher vent for proper airflow. Easy DIY fix, one screw install.

This is a combined motor and circulation pump assembly that drives water through the spray arms during the wash and rinse cycles. It is the main component responsible for recirculating water throughout the dishwasher tub. Replace this assembly if your dishwasher is not spraying water, making unusual humming or grinding noises, or failing to clean dishes properly.

Fix dishwasher not draining or cleaning issues with this pump and motor assembly. Resolves loud grinding noises and poor water circulation problems.

Fix dishwasher leaks or poor cleaning with a new sump cap. Seals the sump opening to contain wash water and protect the pump. Quick DIY replacement.

This small motor actuates the detergent dispenser mechanism in the dishwasher, opening the dispenser door at the correct time during the wash cycle to release detergent. It is driven by the control board and uses a cam to unlatch the dispenser lid. Replace this motor if the detergent dispenser fails to open during the cycle, leaving the soap cup full or detergent undissolved.

Fix a dishwasher that won't drain or clean dishes properly. This pump and motor assembly restores circulation and drainage. Moderate DIY repair.

Fix a washer that won't drain or leaves water in the tub with this drain pump replacement. Restores proper water drainage and spin cycle performance.

This is the drain pump that removes used water from the dishwasher tub during the drain cycle. It is typically mounted at the bottom of the dishwasher and connects to the drain hose. Replace this pump if your dishwasher is not draining, draining slowly, or making unusual humming or grinding noises during the drain portion of the cycle.

Dishwasher leaking or not draining? This sump assembly houses the pump and routes wash water. Replaces a cracked or leaking sump to restore circulation.