Kitchenaid Parts

• Fridge too warm
• Freezer section too warm
• Noisy

Replaced compressor fan. the video on the website showed step by step. very easy and it fixed the problem. Read more

• Little to no heat when broiling
• Element will not heat
• Little to no heat when baking

I ordered the bake unit from appliancepartspro.com; while ordering, I decided to go ahead and replace the oven broiler burner as well. Appliancepartspros.com's videos helped me replace the parts with ease. It took barely 30 minutes to install both. Plus, very fast shipping and correct parts. Now, I do not have to worry about baking during Thanksgiving! Cheers, Sean Read more

Ordered the new gasket from you - installed it and now my freezer is sealed i called to order the correct replacement and they were the very best at helping me !!!!! Read more

I just slid it in and snapped it into place. It was very easy! I am so grateful I was able to find this part at AppliancePartsPros.com. My refrigerator is fairly old and I wasn't sure the parts would still be available. Read more

• Door won't close

I chatted with a rep on Appliance Parts Pros and found out which parts I needed for my model of dryer. Ordered the 2 clips that held the door closed. They arrived the next day!! My dryer was very different than the video but we were able to figure out which screws to remove. The old clips popped out and the new ones popped in. Took about 30 minutes because of there being a top and bottom clip to remove and replace and line up the door parts to screw the screws back in. It works great!! I... Read more

Called in. Talk to a sale rep. Told them the model number, told me that this part would work. Shipped it to me. Snapped it in about 30 seconds. Part was perfect. Read more

• Touchpad does not respond

Most of the instructions you find online are for a different type of coupler that pops off. This model is different, as the coupler unscrews. I found a video for this specific model blender and I'll summarize below: Turn the blender over so the bottom of the blender is facing up You have to pop the bottom rubber feet off. Take off the four screws on the bottom of the blender Lift the bottom of the blender up and off. This may take two people. You'll need a heavy duty wrench under... Read more

My KitchenAid refrigerator was not cooling, but the freezer was working perfectly. The help section here listed three parts that could be defective–defrost thermostat, evaporator fan motor and blade, and air diffuser/damper control–so I replaced them all. The videos were EXCELLENT, and despite the difficulty I had squeezing my shoulders into the small freezer compartment, I installed the parts and my refrigerator is cooling perfectly! THANK YOU FOR THE EXCELLENT REPAIR VIDEOS! I am so happy... Read more

Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more

• Not dispensing water
• Leaking

Being an ex maintainence. person, I went down and turned off the water supply. Then I started to try to find the leak by removing the rear covers for the compressor and valves. Once removing a couple of covers where the dual valve was, I spotted where the water was coming from.I then pulled the electrical plug from the wall. Between the solenoid and valve. I removed the screws that held the valve in place. Then disconnected the three hoses going into valve and removed the two electrical... Read more

Ordered the piece and put it in the refrigerator. Read more

Watched a video. Ordered a thermistor. Made the fix. $100 total including expedited shipping. Diagnosing the problem was more stressful than fixing. Read more

Used screwdriver to push in plastic tabs holding old unit to the top of the refrigerator box Read more

I watched the videos for both jobs, which were excellent and "spot on" for the repair jobs.It didn't take me an hour to replace both lines. Keep up the good work on helping us repair and save money doing our own work. Ken Read more

• Will not fill with water

Ordered new inlet water valve and float switch kit. After repairs it now works fine. However the water inlet valve outlet end for fill hose (not water source) and wire connections (supposedly for this unit) were oriented 180 degrees opposite. I had to gently remove the blue plastic valve off the metal support bracket and turn it around and press back in place. Fortunately it appears it was designed for either orientation. Also the solenoid had to be unclipped and also rotated. Again it was... Read more

I ordered this part and replaced it myself. The photo confirmed I had the correct part. I removed the crisper drawers and all (took 1 minute) and couldn't figure out how to remove this part. Some of the notes claimed there were screws holding it on but that is not correct. One of the large tabs on this part is what keeps this part in place. It's the large tab just slightly to the rear of center. Press it and lift up and the part comes right out. You have to remove the crisper slider from the... Read more