Kitchenaid Parts

Although I only needed to replace the drawer support (end cap) on the right side the kit comes with replacements for both sides. I was surprised to see that the air flow adjustment mechanism that is located on the right side end cap was not included. I should mention that I did not disassemble the drawer mechanisms before ordering the end cap(s). The kit contained only the two molded end caps - no fasteners, mechanisms, or anything else. It turns out that this was all perfectly fine. The... Read more

I took apart the old bucket with a screwdriver and put the new one with no problems. Read more

Ordered front panel and panel control. Also ordered name plate (did not need) front panel already has it. My husband and I had it switched out in approx 10 minutes. Took longer to gather proper tools than it did to do the repair. Looks awesome and original! Read more

Called in. Talk to a sale rep. Told them the model number, told me that this part would work. Shipped it to me. Snapped it in about 30 seconds. Part was perfect. Read more

Used screwdriver to push in plastic tabs holding old unit to the top of the refrigerator box Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

Replaced the broken parts. The water leak was caused by the drain valve not directed into drain pan Read more

REPLACED THE ELEMENT. Read more

The repair went well. Never made this type of repair before. Took me around 90 minutes to complete. The worst part was winging it on how to disassemble the bottom drawers. On my Kenmore Elite, it has three freezer compartment sliding trays. The other difficult part for me was removing the clipped in part on the back of the freezer panel. Without knowing what to do it was a little frustrating. after getting to the evaporator unit, removing built-up ice and replacing the unit was fairly easy. The... Read more

I replaced the circulation pump following the video provided. Read more

• Ice maker won't dispense ice

My LG electric dryer stopped drying the other day and I searched on line for suggestions on what may have caused it to stop working. I came across AppliancePartsPros.com and quickly found some of the most common issues with my LG dryer. The problems were listed in the order of most common occurrence, and had extremely helpful and detailed instructions on how to not only diagnose the problem, they also showed exactly how to access and repair the issue. Unfortunately, it was late on a Thursday... Read more

I just slid it in and snapped it into place. It was very easy! I am so grateful I was able to find this part at AppliancePartsPros.com. My refrigerator is fairly old and I wasn't sure the parts would still be available. Read more

• Element will not heat
• Won't start

Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same... Read more

• Touchpad does not respond

Most of the instructions you find online are for a different type of coupler that pops off. This model is different, as the coupler unscrews. I found a video for this specific model blender and I'll summarize below: Turn the blender over so the bottom of the blender is facing up You have to pop the bottom rubber feet off. Take off the four screws on the bottom of the blender Lift the bottom of the blender up and off. This may take two people. You'll need a heavy duty wrench under... Read more

• Not dispensing water
• Leaking

Being an ex maintainence. person, I went down and turned off the water supply. Then I started to try to find the leak by removing the rear covers for the compressor and valves. Once removing a couple of covers where the dual valve was, I spotted where the water was coming from.I then pulled the electrical plug from the wall. Between the solenoid and valve. I removed the screws that held the valve in place. Then disconnected the three hoses going into valve and removed the two electrical... Read more

I ordered this part and replaced it myself. The photo confirmed I had the correct part. I removed the crisper drawers and all (took 1 minute) and couldn't figure out how to remove this part. Some of the notes claimed there were screws holding it on but that is not correct. One of the large tabs on this part is what keeps this part in place. It's the large tab just slightly to the rear of center. Press it and lift up and the part comes right out. You have to remove the crisper slider from the... Read more