Search Results

This adjustable leveling leg supports and stabilizes your washer. Replacing a worn or missing foot helps the appliance sit flat on the floor, reducing rocking, vibration, and noise for smoother, safer operation. What it does:

• Threads into the base to set height and level the cabinet
• Provides a stable contact point with the floor to minimize movement
• Helps address excessive vibration, rattling, "walking," and out-of-balance issues when the washer isn't level
• Direct replacement for a damaged or missing leveling leg

• 1 leveling leg

• Disconnect power and water before servicing; move the appliance carefully to access the foot
• With assistance, tip or raise the unit as needed to reach the leg safely
• Unscrew the old leg; thread in the new leg by hand and adjust until the washer is level front-to-back and side-to-side
• Tighten the lock nut and recheck stability; run a test cycle to verify

Adjustable leveler leg that stabilizes and levels compatible Whirlpool appliances. Replacing a worn or damaged leveler restores proper balance, reduces rocking, and helps doors and drawers align and seal correctly. What it does

• Raises or lowers the appliance to achieve a level position on uneven floors.
• Stops rocking or wobbling that can cause noise or uneven wear.
• Helps doors and drawers close and seal properly by correcting tilt.
• Replace when threads are stripped, the foot is broken, or the leg no longer holds height.

• Disconnect power (and water supply for appliances with hookups) before working beneath or behind the unit.
• Support the appliance securely (use blocks or have a helper) before removing or adjusting levelers.
• Most levelers screw in/out—turn to raise or lower, then test stability and door alignment.

This grate pad kit replaces the small feet under your cooktop or range burner grates. The heat-resistant pads cushion and stabilize the grate to help prevent wobble, rattling, and scratches on the cooktop surface.

• Provides a protective buffer between the grate and cooktop
• Helps keep grates level and steady to reduce rocking or rattling
• Minimizes metal-on-porcelain or glass contact that can mark the surface
• Common fix when original pads are worn, flattened, missing, or heat-damaged

• Allow appliance and grates to cool completely before servicing
• Lift off the grate; remove old pads and clean the pad recess of residue
• Press new pads firmly into place; ensure each is fully seated before reinstalling the grate
• Replace all pads together for even support and consistent height

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

The Dishwasher Adjustable Leveling Leg is designed to ensure your Samsung dishwasher sits perfectly level on any surface. This genuine OEM part provides stability, preventing unwanted movement and reducing vibration during operation. Easy to install, the LEG-ADJUST allows for precise height adjustments, accommodating uneven flooring and ensuring optimal performance. With durable construction, this part offers long-lasting support, enhancing the lifespan of your appliance. Compatible with a range of Samsung dishwasher models, the Dishwasher Adjustable Leveling Leg seamlessly integrates into your setup, helping you achieve a quiet and efficient kitchen environment. Replace worn or damaged leveling legs with this genuine OEM part to maintain your dishwasher's functionality and reliability.

This leveler assembly supports and stabilizes the appliance at the base. Replacing a worn or damaged leveler helps keep the unit level on uneven floors, reducing vibration, noise, and movement for reliable, quieter operation.

• Provides height adjustment so the appliance sits level and stable
• Helps prevent rocking, walking, or rattling during use
• Aids proper alignment of doors/drawers and overall performance when level is restored
• Replace if the foot is cracked, bent, stripped, missing, or the unit will not stay level

• Disconnect power; turn off water or gas supply if applicable
• Access the base (remove toe-kick/grille or carefully tilt with a helper as needed)
• Remove the old leveler and thread in the new assembly; adjust height and tighten any locknut if present
• The appliance is level front-to-back and side-to-side and all feet contact the floor

This caster assembly supports the dishwasher at the base and lets the unit roll smoothly for positioning, cleaning, or storage. Replace a worn or broken caster to restore easy mobility and stable placement.

• Provides rolling support under the appliance for easy movement
• Helps position the unit properly when setting up or storing
• Reduces dragging that can scuff floors
• Typical failure symptoms include: hard to roll, wobbling/uneven stance, squeaking or scraping noises, and visible cracks or flat spots on the wheel

• Disconnect power and water supply; empty the dishwasher
• Protect the floor, then carefully tip or lay the unit to access the caster location
• Remove the mounting fastener(s), replace the caster assembly, and tighten securely
• Set the unit upright, verify smooth rolling and stable placement, then reconnect utilities

This adjustable leveling leg threads into the appliance base to support and stabilize the unit. Replacing a worn or missing foot restores proper leveling for smoother operation, better door alignment, and reduced vibration.

• Provides height adjustment to level the appliance on uneven floors
• Helps keep the unit stable to minimize rocking and rattling
• Improves door alignment and closure when the cabinet is properly leveled
• Replaces a cracked, stripped, or missing leg

• Disconnect power; if your appliance has a water line, turn off the supply and carefully move the unit to access the leg.
• Support the appliance to relieve weight; unthread the damaged leg and start the new leg by hand to avoid cross-threading.
• Adjust height by turning the foot; use a level to ensure the cabinet is plumb and stable.
• Tighten carefully and recheck stability after the appliance is set back in place.

The Range Leg Leveling Kit is designed to provide stability and balance to your Samsung range. This genuine OEM part includes adjustable legs that ensure your appliance sits evenly on any surface, eliminating wobbling and improving overall performance. Easy to install, the kit allows for precise leveling, helping to maintain the range's alignment during cooking. By using the Range Leg Leveling Kit , you can enhance the safety and functionality of your kitchen setup. This durable kit is specifically compatible with various Samsung range models, ensuring a perfect fit and reliable performance. Whether your range is uneven or has been subjected to shifting, this genuine OEM part offers a straightforward solution to restore its stability. Investing in the Range Leg Leveling Kit ensures your Samsung range operates smoothly, providing you with a consistent and enjoyable cooking experience.

The Leg is an OEM part for LG dishwashers. It serves as a critical base component that elevates the dishwasher body above the floor for proper drainage. Legs are constructed with durable corrosion-resistant materials and adjustable height features to accommodate most flooring types. 

Symptoms of a bad leg can include:

• The dishwasher wobbles or is uneven during operation
• Standing water or improper draining of wash water  
• Visible damage like cracks, bending, or rust affecting stability

Causes of leg failure typically arise from normal wear over extended use of hard flooring. Replacing deteriorated legs restores the appliance's security and balance for optimum performance.

This affordable OEM LG part ensures the dishwasher stays firmly in place during cycles while conveniently adjusting to most installation situations. It provides customers with many more trouble-free years of use. This replacement leg is also compatible with KitchenAid models.

Single unit. Includes foot pad.

This leveling leg threads into the base of your appliance to provide a stable, adjustable footing. Replacing a worn or missing leg helps keep the cabinet level, reducing vibration and noise for smoother, safer operation.

• Adjusts height so the unit can be leveled on uneven floors
• Maintains solid floor contact to minimize rocking or walking
• Helps reduce vibration and rattling noises during operation
• Signs you need this part: appliance wobbles, sits unevenly, or a foot is missing/damaged

• Disconnect power; for gas units, also shut off the gas supply
• With assistance, carefully tilt or raise the appliance to access the leg
• Unscrew the old leg and thread in the new leg by hand; use a wrench if needed
• Level the unit front-to-back and side-to-side; ensure all legs firmly contact the floor

This parts assembly is a pre-packaged set of components used to replace a worn or damaged group of parts in one area of the appliance. Installing the matched assembly helps restore proper fit and reliable operation.

• Replaces multiple small components as a single matched set
• Restores alignment and function in the related mechanism
• Can help with looseness, rattling, poor fit, or intermittent operation
• Built to match original form and connection points for correct fit

• Disconnect power and shut off water or gas before servicing
• Use your model's exploded view/service manual to locate and orient
• Keep track of screws, spacers, and clips; transfer any reusable hardware
• Verify smooth operation before restoring power and normal use

An adjustable leveler that supports and raises or lowers the appliance to help stabilize it on uneven floors. Restores proper alignment to reduce rocking, vibration, and door misalignment for improved performance and safety. What it does:

• Provides height adjustment to level the cabinet and prevent rocking
• Helps doors close and seal correctly by correcting leaning or unevenness
• Reduces vibration and movement that can cause noise or wear
• Simple turn-to-adjust design for fine tuning appliance position

• Unplug the appliance (and shut off water supply for units with plumbing) before working nearby
• Support the appliance when adjusting so it does not tip; use a helper or appliance dolly as needed
• Turn the leveler by hand or with a wrench; adjust both front/back or left/right sides evenly and re-check with a level

The Leveling Leg is an OEM part for Frigidaire dryers. It adjusts to stabilize the dryer on uneven floors during operation.

Subjected to vibrations, repeated adjustments expose leveling legs to wear over extended use. Causes of damage include common plastic stress fractures.

Causes of a problematic leveling leg can include:

• Loosened mounting allowing dryer movement
• Deformed, cracked or damaged plastic dampening
• Inability to adjust height or reliably stabilize weight

Symptoms include:

• Excessive shaking or noise related to an uneven base
• Difficulty configuring proper ventilation clearances
• Premature component fatigue accelerating repairs

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.