Leg Or Foot

An adjustable leveler that supports and raises or lowers the appliance to help stabilize it on uneven floors. Restores proper alignment to reduce rocking, vibration, and door misalignment for improved performance and safety. What it does:

• Provides height adjustment to level the cabinet and prevent rocking
• Helps doors close and seal correctly by correcting leaning or unevenness
• Reduces vibration and movement that can cause noise or wear
• Simple turn-to-adjust design for fine tuning appliance position

• Unplug the appliance (and shut off water supply for units with plumbing) before working nearby
• Support the appliance when adjusting so it does not tip; use a helper or appliance dolly as needed
• Turn the leveler by hand or with a wrench; adjust both front/back or left/right sides evenly and re-check with a level

Adjustable leveling leg threads into the dryer base for stable footing. Replace missing, worn, or broken legs to level your unit on uneven floors.

Adjustable leveling leg threads into washer base to stabilize and level the cabinet. Replace worn, missing, or broken legs to prevent rocking and vibration.

Includes one foot pad. Four are required for each grate. Order as needed. For kit of 8 grate feet with adhesive, order 5304475129.

Twin-wheel caster for portable dishwashers. Replaces worn, broken, or missing wheels to restore smooth rolling and prevent floor scuffing. Installs at base.

Adjustable leveling foot that stabilizes and levels your appliance on uneven floors to stop rocking and improve overall stability. Simple replacement for a worn or damaged foot to restore a solid, level setup. What it does:

• Threads into the appliance base to support weight and set the appliance height
• Lets you level the appliance to stop rocking or tilting on uneven floors
• Helps reduce vibration and shifting during operation
• Common symptom fix: appliance wobbles, is unlevel, or rocks when pushed

• Disconnect power and pull appliance away from the wall before working underneath
• Support the appliance so it cannot tip; adjust the foot by turning until the unit is level
• Recheck level front-to-back and side-to-side; tighten any retaining hardware if present
• If rusted or stuck, use penetrating lubricant and proper tools; avoid forcing parts in a way that could damage the cabinet

Replacement foot for microwaves. Provides stable, cushioned support for the cabinet or removable rack. Needed when original is cracked, broken, or missing.

Fixed rollers with leveling screw for the left hand side. For right side, order part 241889001.

This small roller supports and allows smooth sliding of a storage basket or drawer inside the refrigerator or freezer compartment. It mounts to the interior frame or rail and reduces friction so drawers glide in and out easily. Replace this roller if your basket sticks, wobbles, or no longer rolls smoothly, or if the roller appears cracked or worn.

Threads into the leveling leg or adjuster bracket to raise or lower your refrigerator cabinet. Replace if stripped, missing, or worn for stable footing.

This is a threaded leveling leg assembly that screws into the base of a washing machine. It allows you to adjust the height at each corner to keep the appliance stable and level on the floor. Replace this part if the leg is stripped, broken, or if your washer vibrates excessively or walks across the floor during the spin cycle.

This replacement rubber foot cushions the machine's contact point with the floor to improve stability, reduce vibration, and protect surfaces. Replace a worn or missing foot to restore steadier, quieter operation and easier leveling.

• Provides a cushioned, non-slip contact point between the appliance and floor
• Helps absorb vibration and reduce rattling or movement during cycles
• Aids in proper leveling and overall stability
• Replace when cracked, flattened, or missing, or if the unit rocks or "walks"

• Disconnect power; for washers, also turn off water. If applicable, shut off gas supply
• Carefully tilt or raise the appliance with assistance and proper lifting support
• Remove the worn foot and install the new foot on the leveling leg or base as designed, ensuring it seats fully
• Re-level the appliance and tighten any locknuts; verify stable operation

Threads into range base to support and level the appliance on uneven floors. Replace if foot is worn, cracked, broken, or missing to restore stability.

This Support (mounting bracket) secures internal components and stabilizes the appliance's assembly to help prevent sagging, misalignment and excess vibration. It's a small replacement that restores proper fit and reduces rattling. What it does:

• Provides a stable mounting point for panels or internal assemblies
• Keeps components aligned to prevent binding or wear
• Reduces noise caused by loose or sagging parts
• Helps stop intermittent contact or rubbing that can cause rattles

• Disconnect power (and water, if applicable) before servicing
• Access may require removing outer panels or trim; keep track of fasteners
• Support the assembly while replacing the bracket to avoid strain

This replacement leveling screw secures and adjusts an appliance's leg so the unit sits level and stable on the floor. Restores proper tilt for even door operation and stable performance. What it does:

• Replaces a worn or damaged leveling screw used to raise or lower an appliance leg
• Helps stop rocking, reduce vibration, and keep doors aligned
• Common fix when an appliance tilts forward/back or is uneven on the floor
• Works with the corresponding leveling leg/assembly to set final height

• Support the appliance before adjusting or removing leveling hardware to prevent tipping
• Use appropriate hand tools; tighten securely but avoid over-torquing
• No electrical disconnection is typically required, but unplug if working near electrical components
• If the leveling leg assembly is damaged, replace the entire leg/assembly per manufacturer instructions

This rubber foot pad sits at the bottom of your washer's leveling leg to provide stable, non-slip contact with the floor. It prevents the washer from sliding during operation and protects your floor from scratches or damage. Replace this pad if your washer moves during spin cycles, makes noise against the floor, or the rubber foot is cracked or missing.