Lg Parts

This pump casing assembly forms the sealed housing around the pump, channeling water through the system. Replacing a cracked or warped casing helps stop leaks and restore proper water flow and overall pump performance.

• Houses the pump impeller and seals the pump chamber to contain water
• Directs water flow between the tub/sump and the pump for efficient operation
• Helps maintain proper water pressure within the pump circuit
• Common symptoms of a failing casing include leaks near the pump area, weak water movement or poor draining, unusual grinding/rumbling noises, or visible cracks/warping

• Disconnect power and shut off water supply before servicing
• Access the pump (typically from the bottom or rear)
• Transfer any existing O-rings, clamps, and screws as needed; clean sealing surfaces
• Reassemble carefully, reconnect hoses, and run a test cycle to check for leaks

THERMISTOR ASSEMBLY,PTC

The Damper Motor Support is an OEM part for LG refrigerators. It holds the damper motor in place, ensuring proper air flow between the refrigerator and freezer compartments. This support is essential for maintaining the correct temperature balance within the appliance.

Causes of a bad damper motor support can include wear and tear over time, physical damage from impacts, or exposure to moisture that can weaken the support structure. A faulty support can lead to improper functioning of the damper motor, affecting the refrigerator's cooling efficiency.

Symptoms of a bad Damper Motor Support include:

• Inconsistent temperatures between refrigerator and freezer
• Unusual noises coming from the damper area
• Visible damage or cracks in the support
• Reduced cooling efficiency

This OEM LG part is also compatible with Sears/Kenmore models.

This plastic tube carries water within your refrigerator between internal components. Replacing a brittle, kinked, or leaking line restores dependable water flow and helps prevent drips that can damage interiors, cabinetry, or floors. What it does

• Routes water between internal components (such as valves, filters, reservoirs, and dispensers)
• Helps maintain proper water flow and pressure when intact and unkinked
• Typical failure symptoms: water leaks, slow or no water flow, visible cracks, flattening, or kinks
• Age- or heat-related hardening can cause stress cracks near bends or fittings

• One plastic tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note original routing and clip locations; avoid sharp bends, abrasion points, and hot surfaces
• Insert tube ends fully into their fittings (quick-connect or compression, per design) and gently tug to confirm they're seated
• Restore water, purge air as needed, and check all joints for leaks before pushing the unit back

This is a spider arm assembly for washing machines. Another name for the spider is the rear tub support because it provides support for the outer tub. The spider has three legs that are approximately 10 inches long each. washing machines might need a new spider arm assembly if it is very noisy, if it shakes excessively while running, if the drum is emitting burning smells at high speeds, or if it is smoking. If upon visual inspection, the spider arm assembly is rusted or corroded, it will need to be replaced. The dryer drum may appear to have cracks, but this is how it is manufactured during the casting process. This is a genuine LG part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific spider arm assembly is compatible with washing machines that are LG and Kenmore manufacture.

This radiant surface element mounts beneath the glass cooktop to heat a surface burner. Replace it when a burner won't heat or heats intermittently to restore normal, consistent cooking performance.

• Generates radiant heat under the glass-ceramic top for a surface burner
• Cycles on and off to help maintain the set temperature
• Typical failure signs: no heat, intermittent heat, or visible damage to the element/terminals
• Used on electric ranges and glass cooktops

• Disconnect power at the breaker and allow the cooktop to cool fully before service
• Lift/hinge the glass top and support it to avoid stress or cracks
• Note wire positions; transfer any mounting clips/brackets from the old element to the new
• Ensure the element sits level under the glass and all connections are secure before reassembly

This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.

• Secures panels, brackets, and mounting points as specified by the manufacturer
• Replaces screws that are lost, damaged, corroded, or stripped
• Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
• Maintains proper alignment and stability of the assembly

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to its original location; start threads by hand to avoid cross-threading
• Use the correct driver; tighten snugly without over-torquing into metal or plastic
• Refer to your model's parts diagram to correct location and quantity

This thermistor holder secures the temperature sensor in place inside the dishwasher, ensuring accurate water temperature readings for proper wash and dry performance.

• Holds the thermistor securely in the sump/tub area
• Helps the control accurately monitor wash water temperature
• A loose or missing holder can cause temperature-related wash issues
• Common symptoms include temperature errors or poor cleaning/drying when the sensor isn't properly positioned

• Disconnect power and turn off water supply before servicing
• Access the sensor location from the tub/sump area; note original orientation
• Transfer the thermistor into the new holder and snap the holder into place
• Inspect the sensor wiring and seals while reassembling

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

This gasket creates a watertight seal between mating parts in the dishwasher's water system. Replacing a worn or damaged seal helps stop leaks during cycles and maintains proper wash performance. What it does:

• Seals the joint between components such as the sump, pump housing, or inlet assemblies
• Prevents water leakage under pressure during fill, wash, and drain
• Helps maintain spray pressure by reducing internal bypass
• Common symptoms include water on the floor or in the base pan, and a flattened, cracked, or brittle old gasket

• One gasket

• Disconnect power and turn off the water supply before servicing
• Access the gasket location and remove any retaining hardware
• Remove the old gasket and clean both sealing surfaces thoroughly
• Seat the new gasket evenly without twisting; tighten fasteners/clamps uniformly and run a test cycle to check for leaks

The Cap Cover is an OEM part for LG refrigerators. This cover is designed to protect and secure various components within the refrigerator, such as the water filter or other internal mechanisms. Its role is to ensure that these components are shielded from debris, moisture, and potential damage, maintaining the overall efficiency and cleanliness of the appliance.

Causes of a bad cap cover can include wear and tear over time, cracks or breaks from accidental impacts, or warping due to exposure to temperature fluctuations. Misalignment or improper installation can also contribute to the cap cover becoming damaged or ineffective.

Symptoms of a bad cap cover include:

• Loose or missing cover
• Visible cracks or damage on the cover
• Debris or moisture accumulating in areas meant to be protected
• Misalignment or difficulty in securing the cover properly

This OEM LG part is also compatible with Sears/Kenmore.

This replacement lamp socket holds the light bulb and provides a stable electrical connection so your appliance light works reliably. Replace a heat-damaged or loose socket to restore consistent illumination and help prevent flicker, arcing, and premature bulb failure.

• Secures the bulb and connects it to power
• Restores proper interior or work-area lighting
• Addresses flickering, intermittent light, or bulbs failing early from poor contact
• Replaces sockets that are cracked, melted, or discolored

• Disconnect power at the breaker or unplug before servicing
• Allow the area to cool; wear gloves and safety glasses
• Note wire positions and transfer one lead at a time to the new socket
• If servicing a microwave, access only the lamp area per your model instructions; do not open the cabinet—internal components can retain high voltage

This replacement lint filter fits in the dryer's lint trap to catch lint and fibers from each load. Replacing a torn or warped screen helps maintain airflow, improves drying performance, and keeps lint from circulating back onto clothes.

• Traps lint and debris drawn through the lint trap during drying
• Helps maintain proper airflow and protect the blower and vent path
• Replace if the mesh is torn, the frame is cracked/warped, or it won't stay seated
• Common symptoms: longer dry times, excessive lint on clothing or in the drum, difficulty inserting/removing the filter

• Disconnect power to the dryer before servicing
• Lift out the old filter and vacuum lint from the chute and surrounding area
• Install the new filter fully seated and flush in the opening; do not run the dryer without a filter
• Clean the lint screen before each cycle; check external venting if dry times remain long

This DC motor powers the appliance's cooling fan to move air across coils and through compartments. Replacing a weak or failed motor restores proper airflow for steadier temperatures and quieter, more efficient operation. What it does:

• Drives the fan that circulates air through the evaporator or across the condenser
• Helps maintain even cooling and prevent temperature swings
• Replaces a motor that won't start, runs intermittently, or makes grinding/squealing noises
• Can help address poor cooling, warm spots, or frost/ice buildup from lack of airflow

• 1 DC motor

• Disconnect power before servicing; wear cut-resistant gloves
• Access the fan area per service information (rear interior panel or machine compartment)
• Transfer the fan blade and any grommets/brackets/screws from the original motor if needed
• Seat the motor securely, route wires clear of the blade, and verify the fan spins freely before reassembly

This holder assembly secures and guides the door latch components so the door closes firmly and the safety interlock switches engage. Replacing a worn holder restores reliable latching and helps the unit start consistently.

• Supports and aligns the latch mechanism within the door
• Ensures door hooks engage the interlock switches for safe operation
• Helps prevent a door that won't latch or pops open
• Common symptoms: unit won't start or shows a door error unless you press on the door

• Disconnect power at the breaker before service; microwaves contain high voltage even when unplugged
• Remove the door, separate the inner/outer panels, and transfer the latch holder
• Reassemble carefully, verifying smooth latch movement and proper door alignment
• Test door closure and operation before returning to service

This is a factory parts kit used to service and restore proper operation on compatible appliances. It replaces worn, damaged, or missing small components so assemblies fit correctly and operate as designed. What it does:

• Provides the exact small parts specified by the manufacturer for the application
• Restores proper fit and function where original pieces are worn, damaged, or missing
• Helps eliminate looseness, rattling, misalignment, or poor operation caused by incomplete hardware
• Built to original dimensions and materials for reliable performance

• One parts assembly kit

• Disconnect power and, if applicable, shut off gas/water before servicing
• Follow your model's service manual to identify part locations and orientation
• Use proper tools; handle sharp edges and small fasteners with care
• Test operation after reassembly and verify there are no leaks, rubbing, or loose hardware