Lg Parts

Replaced the inlet valve with some difficulty. First problem was getting off the back cover off to access it, no rhyme or reason to why they made that so difficult. Second problem was getting the inlet valve off. It was a bit tricky to maneuver. Eventually the new part went on with some tricky maneuvering again. One thing I noted was there were no screws (2) that secured the part in place. Besides the one hose and three hard plastic holes the part slid into, there were two plastic clips that... Read more

I ordered a new vario motor and a soap dispenser. I turned off the water and the breaker, disconnected the water line and the power at the front base of the unit, disconnected the drain hose from the garbage dispenser, and pulled out the dishwasher and laid it on a blanket on its face. I unscrewed and removed the plainly visible vario motor on the bottom of the machine and removed the cam from the shaft. I then used a needle nose plier to carefully turn the D-shaft on the new motor to exactly... Read more

Replaced plastic housing for $100. Recommend buying the whole assembly though. Cost a bit more but you would be done in 15min. When you just replace the housing, you have to disassemble the old one very carefully to reuse several parts that do not come with the housing. A lot of fragile plastics. Plus, make sure you have GooGone and 3M thin tape handy; you will absolutely need it. Again, buy the whole assembly and save time and headache. Read more

Replaced freezer door gasket. Door gaskets needed replacement did those as well Read more

When Microwaving food, the display panel would seem to act normal, but the typical microwave sound would be absent. No microwave action would occur. Eventually an F5 code would display. Problem was the upper door switch. Found it by opening up the cabinet, removing the display panel (1 screw and a couple of plugs) and testing all three micro switched with a meter. Two switches are for the door and one for some kind of ventilation flap. They are all in the same area. Go to YouTube to see... Read more

Unplug refrigerator. Use non marring (plastic trim stick) tool to gently pry loose the plastic assembly containing the PCB display beginning at the lower edge and proceeding around the outer edge. Disconnect all connectors and note the routing of each wire harness and connector (take pictures on cellphone as necessary). Remove two screws holding inner PCB mount bracket in place to expose actuator, flapper door and linkage. Replace actuator (three mounting screws) and ensure that actuator... Read more

Removed and replaced the compressor start relay. Read more

First determined drain discharge hose was clear. Turned of power to dishwasher. I did not find it necessary to remove the dishwasher. I simply removed the lower service panel at the floor and was able to easily remove the defective pump, unplug it, replace the small rubber check valve flapper before the pump inlet and reinstall the new pump assembly. The dishwasher surprisingly cleans and runs quietly like new again although I found no excuse for the pump failure as it is well designed. Never... Read more

Elderly neighbor charged $100 for factory tech to inform her that the part wasn't available anymore, so I ordered 2 from Appliance Parts Pros.com (one for a spare) and when they arrived a few days later, I installed then in about 20-25 minutes. I had to remove all the food off the door shelf so I could lift the door off the hinge to replace the bushing. That took 5 minutes. Shame on the tech that went by the date of manufacture rather than checks by model and serial number to see if the part... Read more

1. Googled "appliance replacement parts" - found two sites to consider 2. Researched parts needed via a exploded diagram - can't fix it if you can't name it. 3. AppliancePartsPros.com had the easiest diagram and after checking, the lowest price. 4. Parts showed up within a couple of days - an in-transit note was helpful. 5. The part screws in but watch out you don't break the tiny black pin holding the part on in addition to the screw. Needed JB Weld to fix that. Read more

• Fridge too warm

Replaced the Thermistor Assembly and also picked up Overload Protection circuit per the comments posted by the "experts" on the web site. Both parts cheap enough. I ordered parts at 3:30 in the afternoon and they showed up the next morning from half way across the country. Outstanding service. It also fixed the 9 year old refrigerator. Replacing the parts took about a half hour most of which was moving the unit from the wall and removing the panel to get at the parts. Read more

A couple of screws and a connector. Easy peasy. Read more

Ordered new tube part AJR56656503 for Lg LFX25978ST/01 watched a lot of videos but none showed how to remove the door tube end from its connection so I just cut and spliced the new tube to the old under the cover for the door hinge area after feeding it from the back of frig to that area. It was easy till I tried to remove the line end from ice maker area. Read more

• Fridge too cold
• Fridge too warm

I replaced the evaporator sensor. Your company sent me the exact sensor I needed at a great price. No other company was able to help. No call was needed. Your website was great. Read more

Replaced the cheap plastic lever supporter with another LG OEM cheap plastic lever supporter. I should have bought two as I can see this problem happening again. Job was a simple fix and only required a Phillips head screwdriver. I did not need to remove any connections as there was enough room and wire to pull out the oven control assembly and make the repair. One word of caution is to be careful as the sheet metal internal cover and bottom of the control knob panel is razor... Read more

Bought your craft ice maker. Read more