Washer Control Board

After much reading on line regarding my problem. I decided to do any test that I could to try to diagnose and fix this myself if I could. This took a lot of time and patience to get the answers on how to go about this from "experts" as some of the info was contradictory. I was almost about to give up and buy a new washer with less electronic parts and buttons as advised by an honest appliance technician . I tried one more thing first which was to disconnect the lead wires connected to the MCU .... Read more

Replace the Mainboard control and push the start button. Read more

We started getting the F06 code when on the normal cycle it was time to Rinse/Spin, pointing to a speed/tachometer issue on the motor. After several attempts of unplugging from power and restarting the cycle it would eventually start working for the rest of the laundry session. The Whirlpool technician after a brief look on the underside determined it was the motor and had to be replaced, even tough all troubleshooting tests on the motor were ok. I insisted that the probability was much higher... Read more

• Timer will not advance

After opening the area where the timer was housed, I removed the old timer & replaced it with the new one. The repair was so easy we were back to washing clothes in 10 minutes. Read more

Watched the video , perfect instructions, part on time, right part , took 10 min to replace Read more

Found replacement timer at Appliances Parts Pros. Ordered on a Sunday (as all appliances fail on the weekend) and with expedited shipping got the part on Tuesday morning. Video from Appliance Parts was very helpful and entire replacement took less than 15 minutes. I also purchased a timer for a dryer earlier and had the same positive experience. Read more

I started by replacing the lid switch without the desired result. So I decided to replace the timer unit. It works like a new machine at the moment. At least on the first trial load. More loads will convince me that it is fixed for sure. I cannot be more complimentary about Appliance Parts Pros as I live very remotely in West Texas. The part arrived quickly and it was the exact right part required as ordered. This is my second order and I will return for more parts if I need them. Read more

The washing machine intermittently would not agitate or spin. A reset of the timer dial fixed it. Then nothing fixed it. Originally thought it was the timer but father wanted to check out other possibilities. So he brought his meter over and went through all that he could, including checking power to the motor below. All was good electrical-wise. On the holiday, January 1, a rep. at AppliancePartsPros assured me that if a new timer did not fix the problem, I could return the item, even... Read more

The error code implies a faulty fill valve. This was not the case for me. Replacing the main PCB assembly solved the problem. I have run two full loads since the repair with no problems. Read more

Easy. Opened the front panel, removed the timer, went on line with the part number. Part arrived the next day and I installed it in 2 minutes. FIXED. Read more

Took out old timer, and upon inspection notice some electrical arcing( burned areas). I installed new timer and worked perfectly. Problem was that it would fill up with water, but after it was filled the timer kept going but washer was not agitating. Only thing that worked was delicates wash. Important Disconnect/ unplug power cord! 1. Remove knob, center cap pops off revealing a pin. Slide that off and the knob should come off. 2. Removing knob should reveal 2 socket screws remove... Read more

I called AppliancePartsPros and gave them the detail of my problem and that I thought that the timer may be bad. The guy on the phone with me talked to the technical group and came back and told me that they thought that it was the timer. The timer was ordered and the price was $50 cheaper then a local rep here at home. Anyway the part was ordered and came in less then 2 days and when I replaced it the problem was taken care of. The service, price, and time to get the part was great and I... Read more

Ordered a new timer from Appliance Pros.com Read more

Checked circuit breaker to d/w first. Good. Went to website to see no power issues. Most all of them mentioned the noise filter being the problem. Removed filter from machine and found the corner melted where fuse is located. Ordered new filter, installed, and now have power to switches. All the information I found on the website really made this a easy job to get done. Read more

Put a new control board in and problem solved. Read more