General Electric Cap Or Cover

This evaporator cover assembly protects the refrigerator evaporator coil and helps direct cold airflow for even cooling. It restores proper airflow paths and helps reduce frost buildup for consistent temperature performance. What it does:

• Shields the evaporator coil from direct contact and debris to prevent damage
• Directs cold air through the evaporator compartment for balanced cooling
• Helps minimize frost accumulation on the evaporator when operating correctly
• Reduces rattling or airflow noise caused by a broken or missing cover

• One evaporator cover assembly

• Disconnect power to the appliance before starting any repair
• Remove stored food and defrost the unit if frost blocks access to the evaporator area
• Handle plastic components gently to avoid cracking; use original fasteners and clips
• Inspect and replace other evaporator-area parts as needed for proper sealing and airflow

A single replacement cap handle screw that secures the decorative handle cap to the appliance door, restoring a snug fit and preventing the cap from shifting or falling off. Fits the factory handle cap design. What it does:

• Secures the handle cap to the door handle assembly so the cap stays aligned and tight.
• Fixes common symptoms like a loose or rattling handle cap or a cap that shifts when the door is opened.
• Replaces missing or worn screw hardware to restore original fit and appearance.
• Small OEM-style screw sized for the handle cap mounting location.

• One cap handle screw (black), matching the original hardware.

• Use the correct screwdriver or bit to avoid stripping the screw head.
• Hand-start the screw to ensure proper threading; do not overtighten.
• No special tools or electrical disconnection typically required, but follow appliance-specific service guidance.

A replacement chevron top trim that restores the appliance's front appearance and protects the upper control area from dust and debris. Matches the original black finish for a clean, factory look. What it does

• Replaces cracked, chipped, or faded chevron-style top trim for a finished front appearance
• Covers and protects the upper control area from spills, dust, and light debris
• Restores original fit and alignment with surrounding trim pieces
• Helps maintain consistent styling across the appliance front

• Disconnect power to the appliance before beginning any work to avoid electrical shock
• Typically installs with a few screws and may require removing the backguard or control panel for access
• Handle carefully to avoid scratching the finish; use appropriate hand protection
• Follow OEM instructions for reassembly and torque on fasteners

This white cover hinge replaces a worn or broken hinge that supports and pivots the appliance cover, restoring proper alignment and smooth opening/closing for the lid. Designed as a direct-fit replacement where specified. What it does:

• Provides a secure pivot point so the cover or lid opens and closes smoothly
• Keeps the cover aligned to prevent sagging, rubbing, or binding
• Restores a proper seal/closure when hinge wear causes gaps or misalignment
• Helps eliminate rattling or excess play caused by a damaged hinge

• Disconnect power (and water if applicable) before starting any repair.
• Handle the lid/cover carefully during removal to avoid dropping or injury.
• Basic hand tools are typically required; follow your model's service diagram for location and fastener details.
• Replace with the same OEM part number to ensure fit.

This white corner cap is a small plastic cover that snaps onto a refrigerator door corner to protect the hinge area, conceal fasteners, and restore a finished appearance. Simple replacement for visible damage or missing trim. What it does:

• Covers and protects the door corner and hinge area from dirt and damage
• Hides exposed screws and hardware for a cleaner look
• Prevents sharp edges or gaps that can catch clothing or fingers
• Commonly replaced when cracked, broken, or missing after impact or wear

• Snaps into place
• No wiring; no disassembly beyond removing the damaged cap in most installs
• Disconnect power only if you must remove nearby electrical components; otherwise work with the appliance idle
• Handle plastic parts carefully to avoid cracking; do not force into place

This upper hinge cover protects and finishes the refrigerator door hinge area for a clean appearance and helps keep hinge components free of debris. It restores the original look and helps maintain proper door operation. What it does:

• Covers the top door hinge to protect the hinge and mounting hardware from dirt and accidental contact
• Helps maintain a finished, OEM appearance at the top of the door
• Supports proper door alignment by securing the hinge area visually and mechanically
• Common symptom: broken, cracked, or missing hinge cover that exposes hinge hardware or looks unsightly

• Disconnect power to the appliance before performing service and work with the door supported to avoid injury
• Typically installs with basic hand tools; remove or slightly lift the door per the service manual if required
• Align cover over the upper hinge and secure per OEM instructions; do not force parts into place
• If hinge hardware is damaged or worn, replace the hinge or related hardware per OEM guidance