General Electric Shaft Or Pin

This shear pin secures the washer agitator to the drive shaft and protects the transmission by designed failure when the agitator binds. It's a small, low-cost part that prevents costly gear or motor damage. What it does:

• Locks the agitator to the drive shaft so the washer can agitate and spin
• Designed to break (shear) if the agitator is jammed, preventing transmission or motor damage
• Commonly replaced when the agitator spins freely or the washer won't agitate
• Small part that restores proper mechanical coupling between agitator and drive

• One shear pin

• Disconnect power and water before starting any repair
• Access usually requires removing the agitator; follow your model's service instructions
• Verify shaft and agitator mating surfaces for wear or damage and replace if needed

Replace the implement holder rod in your range hood. This mounting pin secures accessories and attachments. Order a new rod if yours is broken or missing.

Cross bar pinion gear for refrigerator ice maker or dispenser mechanisms. Replace if gear teeth are stripped, worn, or broken causing mechanical failure.

A small metal pin used to secure components in place so they stay aligned and operate smoothly. Replaces a worn or missing retainer pin to restore proper fit and reduce rattling or movement. What it does:

• Secures moving or removable parts by fitting into a mating hole or bracket
• Prevents components from sliding out of alignment during use
• Commonly used where a simple, durable fastener is required
• Symptoms of a bad pin include loose parts, unwanted movement, rattling, or components that detach

• Disconnect power (or unplug appliance) before starting any repair
• Remove adjacent panels or components as needed to access the pin
• Use pliers or a punch to remove the old pin and press the new pin into place; avoid excessive force that could damage surrounding parts
• If the pin secures glass or sharp components, handle carefully and wear gloves and eye protection

This pin locator secures a hinge or shaft pin in place to keep linked appliance components aligned and operating smoothly. It's a small replacement part that restores proper positioning where a locating clip or retainer is used. What it does

• Holds a hinge, shaft, or pivot pin in place to prevent lateral movement
• Restores proper alignment of doors, panels, or linked components
• Helps stop rattling, misalignment, or binding caused by a worn or missing locator
• Works as a direct replacement for the same OEM-labeled locating clip/retainer

• One pin locator

• High-level replacement; basic hand tools usually required
• Disconnect power (and water, if applicable) before servicing appliances with electrical components
• Keep track of small parts and orientation for correct reassembly

Threaded mounting stud secures your cooktop to the countertop or cabinet. Replace if stripped, broken, or missing to properly anchor the unit.

Leveling pin for washer feet. Installs at the base to adjust appliance height and stability. Replace if broken, missing, or stripped threads.

This base shaft is the support shaft that helps the washer's tub or drum stay aligned and rotate smoothly. Replacing a worn shaft restores proper drum support and reduces noise, wobble, and uneven operation. What it does:

• Provides a stable pivot and support for the tub/drum during operation
• Transfers rotational force from the drive components to the drum assembly
• Prevents excessive wobble, vibration, and metal-on-metal contact when intact
• Worn or damaged shafts can cause noise, drum misalignment, or premature bearing wear

• Disconnect power and water supply before servicing; follow all safety precautions
• Replacement typically requires removing the cabinet and drum assembly for access
• Inspect adjacent bearings, seals, and mounting hardware and replace if worn
• Use appropriate tools and follow the OEM service manual

Replacement shelf support stud for refrigerator shelves. Installs to hold shelves in place. Needed when original stud is broken, cracked, or missing.

Replacement timer rod for your oven control panel. This rod connects the timer knob to the timer mechanism. Order a new one if yours is broken or missing.

Replace your microwave's door hinge pin if the original is broken, bent, or missing. This small rod secures the door hinge assembly for smooth operation.