General Electric Valve

This gas valve controls gas flow to the burners and oven, restoring reliable ignition and consistent heat when the burner won't light or the oven won't heat properly. Designed as a direct replacement part. What it does:

• Regulates gas supply to the oven and cooktop burners for proper ignition and consistent flame
• Commonly replaces valves that cause burners not to light or the oven to not maintain heat
• Helps stop irregular gas flow that can lead to weak or fluctuating flames
• Works with the appliance's safety and control systems to open and close gas flow as commanded

• One gas valve as shown

• Shut off the gas supply and disconnect power before starting any repair
• Only install on compatible appliances;
• Tighten gas fittings to the manufacturer's torque spec and test with a leak solution

This safety valve assembly controls the flow of gas to the oven or range burner, restoring safe operation and allowing the appliance to heat when the valve opens. It replaces a faulty shutoff/regulator valve to help address heating issues. What it does:

• Regulates and shuts off gas flow to the burner/oven when required for safe operation
• Commonly used when the oven or burner will not light or stays unlit
• Can stop gas flow if a valve or regulator fails, reducing risk of unregulated gas release
• Works with the appliance's ignition and safety systems to allow normal heating once operating correctly

• One safety valve assembly as shown

• Shut off gas supply and power before starting; follow appliance-specific safety procedures
• Only install on compatible models and use proper fittings; verify orientation and connections match the original
• Check all gas connections for leaks after installation using an approved leak-detection method

This valve kit is the replacement assembly that controls fluid flow to the appliance's internal components, restoring proper operation and helping stop flow-related failures. It replaces a worn or damaged valve to return reliable performance. What it does:

• Regulates flow through the appliance so water or fluid reaches the correct component
• Re-establishes proper filling, dispensing, or flow when a valve has failed
• Stops intermittent or no-flow symptoms that can prevent normal appliance function
• Helps address leaks or drips originating at a faulty valve connection

• Disconnect power and shut off the water or fuel supply before beginning service
• Follow the appliance service manual and use OEM-compatible fittings and seals
• Inspect hoses, connectors and mounting hardware; replace any damaged parts
• After installation, restore supply, check for leaks and verify proper operation

This inlet water valve controls water flow into the appliance, allowing the dispenser and ice/water systems to fill on demand. Replaces a worn or failed valve to restore water delivery. What it does:

• Opens and closes water flow when the dispenser or ice maker calls for water
• Helps maintain proper fill for ice makers and dispenser systems
• Commonly used when dispenser or ice maker does not fill, fills slowly, or runs continuously
• Can leak or drip when internal seals or solenoids fail

• One inlet water valve assembly

• Disconnect power and shut off the water supply before starting work
• Relieve water pressure and have a towel or small container ready for residual water
• Tighten fittings to manufacturer torque; check for leaks after reconnecting water

This safety valve controls gas flow to the range/oven burner and helps ensure reliable ignition and shutoff for safe cooking. Replacing a worn valve restores proper gas delivery and can stop intermittent heating issues. What it does:

• Opens and closes the gas supply to the oven/burner so burners ignite only when commanded
• Prevents uncontrolled gas flow when the appliance is off
• Common replacement when burners or oven fail to light or heat inconsistently
• Can address persistent clicking, weak flame, or failure to maintain temperature

• One safety valve

• Turn off the appliance power and gas supply before starting work
• Inspect and replace any damaged gaskets or fittings during installation
• Use proper tubing fittings and a leak test after reassembly; check for tight seals

This switch valve assembly replaces the appliance's combined valve and switch module to restore controlled on/off operation of the valve. It provides a direct replacement for the original electromechanical valve switch to help the appliance operate reliably. What it does:

• Acts as the combined valve and switch module that controls flow when signaled by the appliance control
• Reestablishes reliable electrical switching to open and close the valve under normal operation
• Commonly used when the valve fails to actuate or when intermittent valve switching occurs
• Helps eliminate symptoms such as failure to start flow, no actuation, or inconsistent on/off cycling

• Disconnect power to the appliance before servicing; if the valve controls gas or water, also shut off supply
• Take photos or mark wiring before disconnecting to ensure correct reconnection
• Handle the part by mounting points; avoid stressing wiring or connectors