Guard, Shield, Barrier Parts

This canopy is a molded trim cover used on compatible microwaves. It finishes and protects the mounting area, helping shield components and restore a clean, secure appearance when the original cover is damaged or missing. What it does:

• Provides a finished look by covering exposed edges and fasteners on the microwave
• Helps protect underlying parts from grease, dust, and moisture
• Assists in keeping adjacent components aligned and secured
• Typical failure signs: cracks, broken/missing tabs, loose fit, rattling, or a missing cover

• 1 canopy

• Disconnect power to the microwave before servicing
• Note orientation; retain and transfer any screws or clips from the original part
• Handle plastic tabs carefully; do not overtighten screws to avoid cracking
• Support the assembly to prevent strain

This replacement cover is a protective panel used in the microwave assembly. It shields internal components from grease and debris and restores a clean, secure barrier when the original cover is cracked, burned, or missing.

• Shields internal components from food splatter, steam, and grease
• Helps maintain proper airflow and safe operation inside the cavity
• Common signs it's needed: cover is warped, cracked, scorched, loose, or missing
• Reduces arcing/sparking or buzzing caused by a damaged or contaminated cover

• Disconnect power before servicing; allow hot surfaces to cool
• Remove screws or release tabs to take off the damaged cover; reuse existing hardware if applicable
• Clean surrounding area to remove grease or debris, then seat the new cover fully and secure without overtightening
• For microwaves, internal high voltage can remain even when unplugged.

This glass light cover shields and diffuses the cooktop light, protecting the bulb from heat, grease, and splatter while maintaining clear, even illumination over your cooking surface.

• Covers and protects the cooktop light bulb
• Diffuses light for more even illumination and reduced glare
• Helps keep grease and debris out of the light cavity
• Replace if cracked, missing, discolored, or not staying secured

• Disconnect power to the appliance before servicing and allow the area to cool
• Support the cover while removing any retaining screw(s) or release tabs
• Reuse original hardware/clips as applicable and seat the cover fully
• Restore power and test the light for proper operation

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

This molded resin cover restores a clean, finished look while protecting the underlying assembly. Use it to replace a cracked or missing cover so components stay shielded and properly secured during normal operation. What it does:

• Shields internal components and provides a finished appearance for the covered area
• Helps keep dust, grease, and debris away from internal parts as designed
• Replaces covers with broken tabs, cracks, warping, or missing sections
• Common symptoms include a loose/rattling panel, poor fit, or visible damage

• One resin cover

• Disconnect power to the appliance before servicing
• Remove any mounting screws and/or release tabs; note the orientation for reassembly
• Transfer reusable clips or hardware from the original cover if applicable
• Do not overtighten fasteners to avoid cracking the plastic

This replacement door glass restores a clear viewing window and the protective barrier on your microwave door. Replace it when the original panel is cracked, shattered, or heavily scratched to keep the door secure and safe to use.

• Provides the see-through window and protective barrier within the microwave door
• Helps maintain proper door rigidity and alignment when intact
• Replace if the glass is cracked, chipped, shattered, loose, or badly scratched
• Reduced visibility, rattling, or visible damage are common symptoms of failure

• Unplug the microwave before servicing; microwaves can retain high voltage—use caution and do not open the cabinet
• Support the door; removal from the hinges may be required per your model's diagram
• Handle glass with cut-resistant gloves; edges can be sharp
• Transfer any reusable trim/clips as directed and verify the door latches and closes properly after installation

This factory glass panel replaces a cracked, shattered, or missing original, restoring a clean, safe cover/viewing surface on your appliance. It helps protect internal areas from splatter and keeps the assembly looking and fitting the way it should.

• Replaces a damaged glass component within the original assembly on applicable models
• Restores a clear, smooth surface for proper appearance and function
• Helps shield underlying parts from spills, grease, and debris
• Common symptoms: cracked or shattered glass, missing piece, sharp edges, looseness/rattling

• Disconnect power before servicing; allow all surfaces to cool
• Wear cut-resistant gloves and eye protection; handle edges carefully
• Support the panel/door during removal and installation to prevent stress on frames/hinges

This mullion guide secures and aligns the refrigerator's vertical door trim so doors close evenly and seals engage properly. Replacing a worn or broken guide helps restore door alignment and reduce drafts at the center seam. What it does:

• Holds the mullion/vertical trim in place and keeps the trim flush with the cabinet
• Guides the doors during closing to maintain even gaps and seal contact
• Prevents the mullion from shifting, rattling, or catching when doors open or close
• Common symptom: loose, misaligned, or damaged center trim causing wind, noise, or uneven door gaps

• Disconnect power before starting service and work on a stable surface
• Remove the mullion/trim and any surrounding gaskets or screws as needed to access the guide
• Use appropriate trim/removal tools to avoid damaging adjacent plastic or gasket material
• Reinstall hardware securely and verify doors close and seals engage properly after installation

This vinyl sleeve fits over a rod, tube, or wire in the refrigerator to protect and cushion contact points. It reduces wear and vibration and helps keep components aligned for smooth, reliable operation.

• Provides a protective barrier at contact points to prevent abrasion or marring
• Helps maintain spacing and alignment for a snug, proper fit
• Cushions to damp vibration and reduce rattles or squeaks
• Replace if the sleeve is missing, cracked, hardened, or if components feel loose or make noise

• Disconnect power; turn off the water supply if working near water lines
• Note the sleeve's original location and orientation; take a photo for reference
• Remove the old sleeve and any debris; slide the new sleeve into the same position
• Check clearance and resecure related parts before restoring power

This refrigerator guide aligns and supports a mating component so it travels smoothly and stays on track. Replacing a cracked or missing guide restores proper movement and helps prevent binding, jamming, or premature wear.

• Guides and stabilizes the movement of the associated part to ensure smooth travel
• Keeps components aligned to prevent rubbing, derailment, or gaps
• Common signs of failure: sticking or binding, wobbling/misalignment, or parts coming off track
• Visible damage such as cracks, broken tabs, or missing pieces on the guide

• Disconnect power; if working near a dispenser or water path, turn off the water supply
• Remove the access panel/bin as needed and retain any screws/clips
• Seat the new guide and reuse existing hardware; verify a secure fit
• Restore power and test the component's movement for smooth operation

This replacement extension support restores proper alignment and secure mounting for the appliance component it attaches to, helping stop misalignment, rubbing, or loose parts and letting the appliance operate smoothly. What it does:

• Replaces a worn, broken or missing extension support used to secure or extend a nearby panel, drawer, or assembly.
• Helps stop rattling, uneven movement, or binding caused by a damaged support piece.
• Restores proper spacing and mounting so associated parts track and close correctly.
• Works as a direct-fit replacement when the original extension is damaged or missing.

• Disconnect power (and water, if applicable) before beginning any repair.
• Handle edges carefully; use basic hand tools and keep original fasteners if reusing them.
• If mounting hardware is missing or damaged, source matching screws/clips separately.

This canopy resistor regulates current to a range-hood or canopy fan circuit to help the blower run at the correct speeds. Replacing a failing resistor can restore proper fan speed control and stop intermittent operation. What it does:

• Controls electrical resistance in the canopy/blower circuit to help regulate fan speeds.
• Helps prevent the motor from running only on a single speed or from failing to start at selected speeds.
• Can cause symptoms such as inconsistent fan speeds, no response from speed controls, or occasional fan cutoff.
• Works with the hood's wiring and control switch to deliver the correct voltage to the fan motor.

• Disconnect power to the appliance before accessing the canopy or electrical connections.
• Inspect wiring and connectors for heat damage or corrosion; replace harness or terminals if damaged.

This is a genuine replacement cover designed to protect internal components and restore the appliance's finished appearance. It provides a durable barrier that helps prevent dust, moisture, and accidental contact with internal parts. What it does:

• Covers and protects internal components behind the panel, maintaining appliance safety and appearance
• Helps prevent debris and moisture from reaching sensitive parts
• Restores a secure fit and alignment of the front/cabinet area
• Useful when the original cover is cracked, warped, or missing

• One replacement cover

• Disconnect power (and water, if applicable) before starting any repair
• Follow OEM service instructions for removal and reinstallation to avoid damaging adjacent components
• Use appropriate hand tools; avoid overtightening fasteners

This resin canopy is the interior ceiling cover inside the microwave cavity. It shields the stirrer area from grease and splatter to help maintain even heating and protect internal components for safer, more reliable cooking. What it does:

• Covers and protects the stirrer/waveguide opening at the top of the cavity
• Helps promote even microwave energy distribution for consistent cooking
• Shields internal parts from grease, steam, and food debris
• Replace if warped, cracked, burned, discolored, loose, or if you notice arcing/sparking inside the cavity

• 1 resin canopy

• Disconnect power before servicing; microwave components can carry high voltage
• Remove the old canopy by releasing tabs or fasteners from inside the cavity
• Clean the cavity roof and seating surfaces before installation
• Ensure the canopy is fully seated and do not operate the microwave without it installed

This replacement shield is a direct-fit protective cover that restores the appliance's factory protection for internal components. It prevents contact with sensitive parts and helps keep wiring and controls clear of debris. What it does:

• Protects wiring, controls and nearby components from heat, moisture and debris.
• Restores the original barrier that helps prevent accidental contact with moving or hot parts.
• Replaces cracked, broken or missing shields that can lead to rattling, exposed components or interference.
• Helps maintain appliance safety and quiet operation when installed correctly.

• One replacement shield

• Always disconnect power to the appliance before starting any repair.
• Handle replacement shield carefully — edges may be sharp; use gloves and basic hand tools.
• Retain and reuse original fasteners unless new hardware is specified; ensure shield is properly seated and secured.
• Do not operate the appliance with shields or covers missing.

This lamp cover is the replacement lens that protects and diffuses your oven's interior light, restoring even illumination while keeping the bulb shielded from heat and food residue. It helps maintain safe, usable oven lighting. What it does:

• Protects the oven light bulb from splashes, crumbs and direct contact.
• Diffuses the bulb for more even interior illumination.
• Replaces a cracked, cloudy, melted or missing lens that can cause dim or exposed lighting.
• Fits over the lamp housing to restore the oven's normal light appearance and function.

• Disconnect power to the appliance before starting and allow the oven to cool completely.
• Handle the cover carefully—wear gloves to protect from sharp edges or broken glass.
• Remove any retaining screws or clips, swap the old cover for the new one, then secure the retainer.
• After installation, restore power and replace the bulb if issues persist.