Guard, Shield, Barrier Parts

A replacement shield that protects internal refrigerator components from damage and keeps nearby parts securely covered. Replaces a worn or cracked cover so panels and wiring stay shielded during normal use. What it does:

• Covers and protects vulnerable components from accidental contact and debris
• Helps maintain proper clearance between parts to prevent rubbing or interference
• Restores a finished appearance where the original shield is damaged
• Useful when the original cover is cracked, broken, or missing

• Always unplug the appliance or shut off power at the breaker before servicing
• Handle the part carefully to avoid sharp edges and to prevent further damage
• Basic tools (screwdriver or nut driver) may be required for removal and installation

This replacement shield is a molded protective mounting shield that helps protect internal appliance components from debris and physical damage, keeping parts aligned for reliable operation and quieter performance. What it does:

• Covers and protects wiring, harnesses, or small components from contact and debris
• Helps maintain proper alignment of nearby parts to reduce wear and noise
• Prevents incidental interference between moving parts
• Restores intended component protection after damage or removal

• One replacement shield

• Disconnect power before starting any repair to avoid shock or injury
• Handle plastic tabs and mounting points carefully to avoid breaking clips
• Reuse original fasteners if undamaged; replace any broken clips before powering appliance

This tub guard protects the washer tub rim and helps prevent clothes from catching or tearing at the top edge. It restores a smooth tub opening and reduces fabric wear for safer, quieter loads. What it does:

• Covers and smooths the exposed tub rim to stop fabric snags and tears
• Helps reduce noise and vibration caused by contact between clothing and the tub edge
• Maintains a finished appearance at the washer drum opening
• Works with the existing tub seal and trim to improve load handling

• One tub guard

• Disconnect power and turn off water before starting any repair
• Remove the washer agitator or top panel only if required for access; follow your model's service instructions
• Align the guard with the tub rim and press into place until it snaps or seats evenly; ensure the seal is continuous
• If any clips or screws are present, reinstall securely; discard damaged guards and replace with correct part

This heat shield protects oven or range components from direct heat, helping prevent damage to nearby panels and wiring. It's a direct-replacement exterior shield used when existing metal shields are warped, cracked, or missing. What it does:

• Diverts and dissipates heat away from control panels, insulation, or adjacent components
• Helps stop heat-related discoloration, warping, or premature wear of nearby parts
• Restores proper clearance and airflow around the oven cavity after shield damage
• Commonly replaced when you see scorched areas, melted trim, or gaps where a shield once sat

• One heat shield (exact shape and mounting holes as shown in OEM diagram)

• Disconnect electrical power (and gas, if applicable) before starting any repair
• Remove oven racks and any trim panels to access the shield; keep track of fasteners
• Compare the replacement to the removed part to confirm fit before fastening
• If mounting hardware is damaged or missing, procure correct OEM fasteners — only the shield is guaranteed to ship

This air divider directs and controls airflow inside the refrigerator to help maintain even temperatures between compartments and reduce frost buildup on shelves and drawers. What it does:

• Guides chilled air through the cabinet to balance temperatures across compartments
• Helps prevent cold spots and excessive frost near vents and shelves
• Supports proper circulation after evaporator airflow is restricted or misdirected
• Common symptom: uneven cooling or noticeable temperature difference between sections

• One air divider

• Disconnect power to the appliance before beginning any work
• Remove shelves or drawers as needed for access; handle plastic parts gently to avoid cracking
• Align tabs and snap the divider into the existing slots; no special tools typically required
• If airflow issues persist after replacement, check vents, damper, and fan for related faults

A shield switch that helps prevent oven/range operation when the door is open and ensures safe control behavior. Replaces a worn or failed interlock switch to restore normal start and door-safety responses. What it does:

• Acts as an interlock micro switch to detect door/cover position and block operation when open
• Commonly replaces a switch causing the control to not start or to behave intermittently
• Can resolve issues like no power to heating elements, control not responding, or oven not entering bake/lock modes
• Small electrical switch that completes or breaks the circuit based on door/cover position

• Disconnect power to the appliance before servicing to avoid shock or injury
• Replace the switch with the same part orientation and secure all connectors firmly
• Verify correct operation by restoring power and testing door open/close and normal cycle starts