Guard, Shield, Barrier Parts

Fan guide for refrigerators. Directs airflow from the evaporator fan. Replace if cracked, broken, or missing to restore proper air circulation.

Factory protective shield panel for dryer assembly. Guards internal components and directs heat or airflow. Replace if cracked, broken, or missing.

This is a flat insulator cover that sits over the waveguide opening inside the microwave cavity. It protects the magnetron's waveguide from food splatter and grease buildup while allowing microwave energy to pass through. Replace this cover if it is burned, scorched, cracked, or has visible arcing marks, which can cause sparking during operation.

Secures and aligns the vertical door trim between refrigerator doors. Replace if cracked, broken, or worn to restore proper door alignment and seal.

Glass light cover for microwave cooktop lights. Shields and diffuses bulb from heat, grease, and splatter. Replace if cracked, broken, or missing.

This replacement extension support restores proper alignment and secure mounting for the appliance component it attaches to, helping stop misalignment, rubbing, or loose parts and letting the appliance operate smoothly. What it does:

• Replaces a worn, broken or missing extension support used to secure or extend a nearby panel, drawer, or assembly.
• Helps stop rattling, uneven movement, or binding caused by a damaged support piece.
• Restores proper spacing and mounting so associated parts track and close correctly.
• Works as a direct-fit replacement when the original extension is damaged or missing.

• Disconnect power (and water, if applicable) before beginning any repair.
• Handle edges carefully; use basic hand tools and keep original fasteners if reusing them.
• If mounting hardware is missing or damaged, source matching screws/clips separately.

Vinyl sleeve that fits over rods, tubes, or wires in your refrigerator. Replace if cracked, torn, or missing to protect contact points and reduce wear.

This replacement shield is a direct-fit protective cover that restores the appliance's factory protection for internal components. It prevents contact with sensitive parts and helps keep wiring and controls clear of debris. What it does:

• Protects wiring, controls and nearby components from heat, moisture and debris.
• Restores the original barrier that helps prevent accidental contact with moving or hot parts.
• Replaces cracked, broken or missing shields that can lead to rattling, exposed components or interference.
• Helps maintain appliance safety and quiet operation when installed correctly.

• One replacement shield

• Always disconnect power to the appliance before starting any repair.
• Handle replacement shield carefully — edges may be sharp; use gloves and basic hand tools.
• Retain and reuse original fasteners unless new hardware is specified; ensure shield is properly seated and secured.
• Do not operate the appliance with shields or covers missing.

Protective cover that shields the range door hinge assembly from debris and damage. Replace if cracked, broken, or missing to restore a clean finished look.

Stamped metal shield that protects the oven's lower cavity and insulation from excessive heat. Replace if cracked, rusted, corroded, or damaged.

Replacement shaft sleeve bushing for washers. Fits over rotating shafts to reduce friction and protect surfaces. Replace when worn, cracked, or missing.

This outer door window glass replaces a cracked or cloudy viewing panel so you can safely monitor cooking without opening the door. Tempered glass matches OEM fit and restores a clear view through the appliance door. What it does:

• Provides a clear, protective viewing panel for the appliance door
• Restores safe visibility when original glass is cracked, chipped, or fogged
• Helps contain heat and splatter behind the door during operation
• Matches OEM shape for correct fit and secure mounting

• Handle with care; tempered glass can shatter if dropped or struck
• Disconnect power to the appliance before removing the door or any fasteners
• Follow OEM diagram for door disassembly and reassembly to avoid damage

Protects wire connection points on your range. Shields exposed terminals from accidental contact and shorting. Replace if cracked, broken, or missing.

Secures and guides the ice maker assembly to prevent shifting during operation. Replace if cracked, broken, or missing to restore proper alignment.

Plastic cover that shields the stirrer assembly inside your microwave. Replace if cracked, melted, broken, or missing to protect internal components.