Fuse Or Sensor

Microwave won't heat or power on? This bottom thermal cut-off protects against overheating by cutting power when excess heat is detected. Easy fix.

If your dryer is overheating, running too hot, or taking extended times to dry clothes, a faulty cycling thermostat is often the cause. Easy DIY fix.

Fix a dryer that won't heat or overheats with this cycling thermostat. Regulates heating element temperature for consistent drying. Simple DIY repair.

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

The Electrode is an OEM replacement part for Whirlpool dryers. It is responsible for detecting the moisture levels in your laundry during the drying cycle, allowing the dryer to automatically adjust the drying time and temperature. It helps prevent over-drying or under-drying of your clothes, saving energy and protecting them from potential damage.

A bad electrode can occur due to wear and tear, damage, or a buildup of debris or lint. If you notice symptoms such as clothes taking longer to dry, the dryer shutting off prematurely, or inconsistent drying results, it may be time to replace the moisture sensor bar electrode.

Symptoms of a bad electrode include:

• Clothes taking longer to dry than usual
• The dryer shutting off prematurely
• Inconsistent drying results, with some items remaining damp

Repair your dryer by replacing the faulty or damaged electrode with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Dryer not heating or overheating? This thermostat regulates temperature during the drying cycle. Common DIY repair that restores proper heat control.

This dishwasher sensor assembly contains the thermistor that monitors wash-water temperature and sends readings to the control. Replacing a faulty sensor restores accurate heating and cycle timing for consistent cleaning and to prevent temperature-related interruptions. What it does:

• Measures wash-water temperature via an NTC thermistor
• Sends a resistance signal to the control to manage heater operation and cycle timing
• Helps maintain target temperatures for proper cleaning performance
• Common failure symptoms include no heat or overheating, long/short cycles, temperature-related errors, or poor cleaning/drying

• Disconnect power at the breaker and shut off water before servicing
• Access the sump area from the bottom; you may need to pull the dishwasher forward for clearance
• Expect some residual water—protect the area with towels
• Seat the sensor fully in the sump opening, reconnect the harness, and run a test cycle to check for leaks and proper heating

Ice maker not producing ice or overflowing? Failed thermistor prevents proper temperature monitoring. Direct plug-in replacement restores ice production.

If your dryer takes too long to dry or overheats, the cycling thermostat may have failed. This part regulates heat by cycling on and off. Easy DIY fix.

This internal-bias thermostat controls exhaust temperature in your dryer, cycling the heat on and off to maintain proper drying temperatures. Replacing a failed thermostat can restore consistent drying performance and help protect the dryer from overheating shutdowns.

• Monitors exhaust air temperature and opens/closes the heating circuit to regulate heat
• Provides the bias function used by automatic cycles for correct temperature control
• Failure symptoms can include no heat or low heat, long dry times, overheating or high-limit trips, and inconsistent cycling temperatures
• Helps prevent thermal cutoffs caused by restricted airflow or faulty temperature regulation

• Disconnect power before servicing; for gas models, also shut off the gas supply
• Access location is typically on the blower/exhaust housing; note wire positions and transfer one at a time
• Ensure the thermostat mounts flush for proper sensing; tighten screws securely
• After replacement, verify good airflow and clear venting to prevent repeat failures

Dryer won't start or overheats? A faulty high-limit thermostat breaks the heating circuit to prevent damage. Easy 5-10 minute DIY replacement fix.

This dishwasher turbidity sensor measures how dirty the wash water is and reports to the control. Replacing a faulty sensor can restore proper cycle times and cleaning performance for consistent results.

• Monitors water clarity/soil level during the wash
• Sends feedback to the control to adjust cycle length, rinses, and heating
• Failure can cause very long or very short cycles
• Can trigger sensor-related fault indications

• Disconnect power at the breaker and shut off water before servicing
• Access the sensor from the bottom near the sump; remove the toe panel if needed
• Unplug the wire harness; release the locking tabs or twist-lock to remove; avoid touching the optical window
• Inspect and reuse the existing seal/retainer if in good condition; seat fully and check for leaks after reassembly

This sensor monitors operating conditions and relays accurate feedback to the control so cycles run properly. Replacing a failed sensor helps restore correct operation and prevent erratic behavior or fault codes. What it does:

• Detects a specific operating condition and sends a signal to the control
• Helps the machine regulate cycle timing and performance
• Can cause error codes, cycles that won't start or advance, or intermittent shutdowns when failing
• Lead to inconsistent temperatures or sensing behavior depending on application

• 1 sensor

• Disconnect power (and shut off gas/water, if applicable) before servicing
• Access the sensor; note wire positions and connector orientation
• Install the new sensor in the same location and orientation; seat connectors fully
• Clear any stored faults and run a test cycle per the tech sheet

Fixes dryer not heating or overheating issues. This safety thermostat monitors temperature and cuts power when too hot. Basic DIY repair, 30 minutes.

Dryer not heating or running too hot? This high-limit thermostat regulates temperature to prevent overheating. Easy DIY fix takes 30 minutes or less.

Fixes long dry times and temperature issues. This dryer thermostat regulates heat cycling to prevent overheating or underheating. Simple repair.