Touch Pad

This is a factory parts kit used to service and restore proper operation on compatible appliances. It replaces worn, damaged, or missing small components so assemblies fit correctly and operate as designed. What it does:

• Provides the exact small parts specified by the manufacturer for the application
• Restores proper fit and function where original pieces are worn, damaged, or missing
• Helps eliminate looseness, rattling, misalignment, or poor operation caused by incomplete hardware
• Built to original dimensions and materials for reliable performance

• One parts assembly kit

• Disconnect power and, if applicable, shut off gas/water before servicing
• Follow your model's service manual to identify part locations and orientation
• Use proper tools; handle sharp edges and small fasteners with care
• Test operation after reassembly and verify there are no leaks, rubbing, or loose hardware

This keypad is the membrane switch mounted behind the dishwasher's control panel. It registers your button selections and sends them to the electronic control, helping restore consistent response when keys are unresponsive, intermittent, or require excessive pressure. What it does:

• Registers cycle, option, and Start/Reset inputs on the console
• Sends those selections to the electronic control for proper operation
• Failure symptoms include: some or all buttons not responding, needing to press very hard, erratic input, or the cycle not starting from the console
• Can also present as stuck/continuous key input or random beeping

• 1 keypad

• Disconnect power at the breaker before servicing; the control console contains live voltage
• Open the door and remove inner-door screws to access the control console
• Note ribbon-cable orientation; insert straight and fully into the board connector without creasing the flex
• Handle electronics with dry hands and ESD care; reassemble without overtightening screws

Restore reliable button response on your refrigerator's control panel. This control keypad registers your selections and sends them to the electronic control so features and settings respond consistently. What it does:

• Provides the button interface for the refrigerator's control panel
• Sends selection signals to the main control board
• Failure can cause dead or stuck buttons, erratic inputs, or no response
• Common symptoms include unresponsive controls, intermittent operation, or unintended changes

• 1 control keypad

• Disconnect power to the refrigerator before servicing
• Carefully remove the control panel/trim to access the keypad; avoid prying damage
• Note connector orientation and avoid creasing the flex cable; seat the connector fully
• Restore power and test all buttons before final reassembly

Color: Black

Color: Black. For white order 5765M440-60.

Color: Black
The Dispenser Cover is an OEM part for Frigidaire refrigerators. The dispenser cover protects the dispenser components from accidental spills, dust, or impact while also adding an elegant styling element to the refrigerator exterior.

Causes of a bad dispenser cover can include cracks or breaks from repeated opening and closing of the door over time. Normal wear from daily use can also cause looser fits or gaps.

Symptoms of a bad dispenser cover include:

• Cracks, breaks or missing pieces of material
• Improperly seated or loose fit when installed
• Spills or condensation leaks into dispenser mechanisms
• Affects the clean appearance of the refrigerator

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Color: Ultimate Silver

This dispenser module manages the refrigerator's ice and water dispenser interface on the door. Sometimes called the dispenser control board or UI module, it reads paddle/button inputs and coordinates dispenser functions for consistent, responsive operation.

• Interprets inputs from the dispenser paddle and selection buttons
• Controls ice and water dispensing functions at the door
• Manages dispenser indicator/display functions
• A failed module can cause no dispensing, unresponsive buttons, dead lights, or intermittent operation

• Disconnect power to the refrigerator before servicing; turn off water supply if working near lines
• Carefully remove dispenser trim and panel; protect the finish and watch sharp edges
• Handle the electronics with ESD care; move wire connectors one at a time to the new module
• Restore power and test all dispenser selections and lighting

This control panel replaces the front console that houses the buttons and indicator lights on your dishwasher. It restores a clean look and responsive inputs so you can select options and start cycles reliably again.

• Provides the user interface for cycle selection, Start/Cancel, and options
• Sends keypad inputs to the main control board for proper operation
• Displays status/option indicators where applicable
• Replaces cracked, faded, or unresponsive consoles to improve usability

• Disconnect power to the dishwasher before servicing
• Open the door and remove inner-door screws to release the console from the door
• Support the wiring; transfer any clips/trim and reuse existing hardware as required
• Avoid pinching the ribbon cable and verify button function before final reassembly

This is the electronic control board that governs the appliance's cooling system. It interprets sensor input and user settings to run key components, helping maintain consistent temperatures when the original controller becomes faulty or erratic.

• Monitors temperature sensor feedback and executes cooling cycles to hold the selected setpoint
• Controls major components on applicable models
• May manage additional functions like defrost timing or alarms depending on model design
• Failure can present as warm or unstable temperatures, unit not starting, short-cycling/running constantly, or unresponsive temperature adjustments

• Disconnect power before service; observe ESD precautions and handle the board by its edges
• Note wire/plug locations; transfer connectors to the new board one at a time
• Secure the board in its mounting and ensure all harnesses are fully seated
• Reassemble covers/panels before restoring power and checking operation

This adhesive faceplate restores the labels and graphics on your oven's electronic control. Replace a faded, bubbled, or peeling overlay so settings and keys are easy to see again for safe, accurate operation.

• Provides printed button labels and display markings for the electronic oven control
• Replaces overlays worn by heat, cleaning chemicals, and normal use
• Common symptoms: faded or unreadable text, bubbling, lifted corners, sticky residue
• Note: Does not resolve unresponsive keys—typically indicates a keypad/touch panel or control issue

• Disconnect power at the breaker before servicing
• Remove trim as needed; gently warm and peel off the old overlay; clean all adhesive residue
• Dry-fit to alignment; peel liner and apply from one edge, smoothing to avoid bubbles
• Press firmly around display and key openings; allow adhesive to set before reassembly

This keypanel support assembly is the front frame that holds the touch keypad and related controls on your range or wall oven. Replacing a cracked or warped support restores a secure mounting surface and proper alignment of the user interface.

• Supports and positions the keypad/overlay and display opening within the control panel
• Provides mounting points for control electronics and trim pieces
• Restores proper alignment so buttons sit flush and operate as intended
• Common signs include a cracked front frame, loose or shifting keypad, or difficulty fastening the control panel

• Disconnect power at the breaker and allow the appliance to cool before servicing
• Remove control-panel screws/trim and place the panel face-down on a protected surface
• Transfer the keypad/overlay and any brackets from the old support to the new one; avoid creasing ribbon cables
• If handling the control board, use ESD precautions; verify color and fit before tightening fasteners

Replace a worn or peeling console label with this control panel overlay. It restores clear, readable graphics on the user interface so settings are easy to see and select, keeping operation straightforward and professional-looking.

• Provides printed legends/graphics for the control panel or touchpad
• Bonds to the panel surface to refresh worn, faded, or damaged markings
• Common symptoms: peeling or bubbling film, cracking/tearing, faded or missing text, hard-to-read controls
• Helps shield the underlying keypad area from light spills and wear

• Disconnect power to the appliance before servicing
• Remove the control panel/escutcheon as needed to access the overlay area
• Carefully peel off the old overlay; clean any adhesive residue and let the surface dry
• Align and apply the new overlay without stretching; press evenly to ensure full adhesion, then reassemble

This control panel overlay is the thin faceplate that mounts over the oven/range electronic control. It restores clear, readable button labels and a clean, factory look so you can select settings confidently.

• Provides printed labels/icons for modes, temperature, timers, and features on the electronic control (ERC)
• Covers the control face for a finished appearance
• Replace when graphics are faded, cracked, bubbled, or peeling
• Helps prevent confusion from missing or unreadable labels

• Disconnect power at the breaker before servicing
• Remove the backguard/control panel to access the electronic control
• Carefully remove the old overlay, clean the surface, and align the new overlay with the display window and button locations; apply even pressure to seat it
• Reassemble, restore power, and verify all functions align with the printed labels

The Overlay is an OEM part for Frigidaire ranges. The overlay protects the touch controls from accidental scratches, spills, and other damage while maintaining tactile button functionality.

Causes of a bad overlay include scratched or bubbled surfaces from cleaning chemicals or improper cleaning methods. Peeling or partial removal of the overlay layers can also occur from repeated use over time or accidental impact.

Symptoms of a bad overlay include:

• Unresponsive or intermittent touch controls
• Visible scratches, cracks, or chips in the overlay surface
• Peeling or lifting of the edge seals
• Discolored or stained appearance

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Main Control Board  is an OEM part for GE refrigerators. This main control board serves as the central control hub for your refrigerator, responsible for regulating various functions such as temperature control, defrost cycles, and overall operation.

A bad main control board can occur due to electrical issues, component failure, or other factors. If you notice symptoms such as erratic temperature readings, unresponsive controls, or complete refrigerator malfunction, it may be time to replace the main control board.

Symptoms of a bad main control board include:

• Erratic temperature readings
• Unresponsive controls
• Complete refrigerator malfunction

Restore proper function to your GE refrigerator by replacing the faulty main control board with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.