Touch Pad

This control panel is designed for use with washing machines. It's on the top back area of the appliance and houses a display and several buttons to control various components in the appliance. It's responsible for starting and stopping components, such as the drain pump and drive motor. If the display isn't working or the washer doesn't spin, fill, or drain, the control panel may be causing the issue.If this part is faulty, it should be replaced. Use work gloves for hand protection and pull the washing machine away from the wall to unplug it. Pull the control knob off the front of the console panel and move to the back of the appliance. Take out the screws on the top of the back panel. Push the control panel back while using a putty knife under the right corner to release the mounting clip. Do the same thing on the other side. Document where the wires are connected to the control panel before removing it. Install the new part and reconnect all the wires.This control panel is made for use with Maytag washing machines. It's an authentic OEM replacement part sourced directly from the manufacturer. The part is sold as an individual item.

The membrane switch is the low-profile keypad behind your microwave's control panel. It registers button presses so you can select settings and start cooking. Replace it if keys stop responding or require excessive pressure.

• Converts keypad presses into signals for the electronic control
• Enables selection of power levels, cook times, and options
• Common symptoms: some or all keys don't work, intermittent response, must press very hard
• If the unit won't start/stop from the keypad, the membrane switch may be faulty

• Disconnect power at the breaker before servicing
• Remove the control panel to access the keypad; note ribbon orientation and routing
• Handle the flexible ribbon carefully—don't crease it—and fully seat/lock the connector

Color: Stainless

The Freezer Control Board is an OEM part for Frigidaire freezers. It manages and regulates the various functions of the freezer, including temperature control, defrost cycles, and compressor operation. This control board ensures that the freezer maintains the correct temperature and operates efficiently.

Over time, the freezer control board can fail due to electrical surges, component wear, or manufacturing defects. When the control board malfunctions, it can disrupt the overall performance of your freezer, leading to inconsistent freezing and other operational issues.

Symptoms of a bad freezer control board include:

• The freezer not maintaining the correct temperature
• The freezer running continuously or not running at all
• Unresponsive control panel or error codes displayed
• Irregular defrost cycles causing ice buildup

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This dispenser interface assembly is the electronic control module behind the refrigerator's ice/water dispenser panel. It reads your button selections and manages the display and lights, restoring reliable dispenser control when the original interface malfunctions. What it does:

• Interprets dispenser keypad inputs (water, cubed/crushed ice, light, lock)
• Sends commands to the refrigerator to dispense ice or water as selected
• Controls the dispenser display and indicator lights
• Failure may present as unresponsive buttons, intermittent operation, or a blank/flickering dispenser display

• 1 dispenser interface assembly

• Disconnect power to the refrigerator before servicing
• Carefully remove the dispenser trim/escutcheon, release locking tabs, and support wiring
• Note and unplug wire harness connectors; handle electronics with ESD precautions
• If your model uses a separate decorative overlay, transfer it from the original assembly before reassembly

This control panel is the exterior fascia at the top of the dishwasher door. It provides the labeled surface for the user controls and restores proper button access and appearance when the original is cracked, broken, or worn.

• Serves as the door-mounted fascia for the dishwasher's user controls
• Provides the labeled button layout and covers/protects the control area
• Replaces cracked, loose, or broken panels that can make buttons difficult to press
• Refreshes worn graphics and scuffed or faded appearance

• Disconnect power at the circuit breaker before servicing
• Open the door and remove the screws securing the console/inner door to release the panel
• Support the panel; transfer any handle/trim and the existing switch/control components as required
• Reinstall, align, and secure screws; restore power and verify button operation

This dispenser control board is the electronic module behind the refrigerator's ice/water dispenser panel. It reads button inputs and powers dispenser functions to help restore reliable dispensing and front-panel control when the original board fails. What it does

• Processes user selections for water, cubed/crushed ice, and dispenser light (model-dependent)
• Sends power to the water inlet valve and auger/dispenser motor as commanded
• Manages dispenser lock and status/display indicators (if equipped)
• Failure symptoms include unresponsive or intermittent controls, no water or ice dispensing, or an inoperative dispenser light

• Includes 1 dispenser control module (electronic board)

• Disconnect power before servicing; use ESD protection and handle the board by its edges
• Remove the dispenser escutcheon/cover to access the module; release locking tabs or screws as needed
• Transfer wire connectors one at a time to the new board, confirming orientation and full seating
• Reassemble, restore power, and test all dispenser functions

This black clock plate is the trim and mounting plate for the range or wall oven clock/timer in the control panel/backguard. It restores a clean, finished look and helps position and support the clock assembly securely.

• Provides the mounting surface and finished opening for the clock/timer module
• Helps align the display and protect surrounding panel edges
• Replace if cracked, warped, missing, or heavily discolored
• Typical symptoms include a loose or misaligned clock, rattling, or visible damage around the display

• Disconnect power at the breaker before servicing; allow the appliance to cool
• Remove the control panel/backguard to access the clock and plate
• Transfer the clock/timer to the new plate and reuse existing hardware
• Align carefully and avoid overtightening to prevent damage; verify display alignment before reassembly

This dishwasher keypad is the membrane touchpad behind the control console. It registers your button presses so you can select cycles and options. Replacing a failed keypad restores reliable button response and allows the dishwasher to start. What it does / symptoms:

• Provides the user interface for cycle and option selection
• Sends button-press signals through the ribbon connector to the electronic control
• Buttons are unresponsive or work intermittently
• Dishwasher won't start when Start/Reset is pressed
• Indicator lights may come on but controls don't respond to input

• One keypad

• Disconnect power at the breaker before servicing
• Access the console/door area to reach the keypad and control
• Carefully release the ribbon connector; avoid creasing or damaging it
• Ensure the ribbon is fully seated and correctly oriented in the control board connector before reassembly

This is the black front cover for the refrigerator dispenser control module. It snaps over the user interface on the door to protect the electronics and restore a clean, finished look when the original cover is cracked or missing.

• Covers and protects the dispenser control module from everyday contact and moisture
• Provides a finished trim around the dispenser controls
• Helps keep the control area clean and secure
• Common symptoms: visible cracks, broken tabs, loose or missing cover, exposed controls

• Disconnect power to the refrigerator before servicing
• Carefully release the old cover's retaining tabs; avoid stressing the wiring or control board
• Align the new cover and press until all tabs fully engage
• Restore power and verify buttons operate and the cover sits flush

This Whirlpool touchpad and control panel is intended for use with wall ovens. The control panel and touchpad provide users with the ability to control the oven's functions. The touchpad can wear out through normal, everyday use over time. The panel itself, although made from stainless steel and very durable, can also begin to wear if not properly cleaned and maintained.Signs that the touchpad might need to be replaced include difficulty pressing the buttons and operating the oven. If the overlay on the display is difficult to read, or if the metal is corroding, it should also be replaced. Before replacing this part, first turn off the breaker to the oven. Then, remove the two screws at the top of the display and pull outward. Remove the control board from the inside and install it in the new panel, then install the panel.This is a genuine OEM part, sold individually. It fits Maytag wall ovens only.

This faceplate is the front cover for the control panel. It restores a finished look and helps protect and support the control assembly so the controls align and operate correctly.

• Covers and shields the control assembly from everyday use
• Provides secure mounting and proper alignment for controls
• Replace if cracked, warped, or if mounting tabs are broken
• Common signs include a loose or missing cover, rattling panel, or misaligned controls

• Disconnect power at the breaker before servicing
• Remove screws/retainers to lift the control panel; support the board and wiring
• Transfer any existing brackets or clips to the new faceplate as needed
• Reinstall, restore power, and test

Each piece is sold separately from the unit. This part is a Whirlpool oven control panel assembly. The control panel assembly and control board act as one unit to make up the central command center of the oven. The front-facing area contains the dials visible to the user, and the rear houses the actual circuit board. When a control panel assembly or the control board malfunction, the oven is essentially out of commission. In some cases, the malfunction may be gradual, with specific settings and functions going out one at a time. If burners begin to short out individually, or certain functions cannot be toggled on or off, it may be time for a replacement control board assembly.Installation of the part on compatible models is fairly simple. There is one screw on each side of the control panel assembly on the front of the oven. Remove these screws and the control panel should slide off with ease. There are two connecting wire harness components on either side of the control panel. Remove these connections and replace with the new control board, and pop it back into place before replacing the screws. This component can be used with Whirlpool or Maytag appliances. It is a genuine OEM product sourced directly from the manufacturer.

This replacement control panel, also called the backsplash assembly, is the structural console on the rear of the dryer top where the timer and switches mount. It restores secure control mounting and a clean, finished appearance when the original is cracked or damaged.

• Houses and supports the dryer's timer and control switches
• Covers and helps protect console-area wiring from contact
• Aligns control shafts through the panel openings for smooth knob operation
• Common signs of failure: cracked panel, broken mounting tabs, loose or rattling controls

• Disconnect power; for gas models, also shut off the gas supply
• Remove control knobs and mounting screws, then tilt or lift the console to access the panel
• Transfer timer/switches and any brackets from the old panel to the new one, keeping hardware organized
• Do not overtighten screws; verify all controls turn and click freely before restoring power

This replacement panel forms the finished control area of your appliance. It provides a sturdy mounting surface for the user interface and protects the electronics behind it, restoring proper alignment, appearance, and protection when the original panel is damaged. What it does:

• Covers and protects the control compartment and wiring
• Provides mounting points for the control board, switches, knobs, and/or overlay
• Keeps controls aligned and secure for proper operation
• Common signs it's needed: dents, cracks, broken tabs, sharp edges, or controls that won't sit flush or stay secured

• One panel

• Disconnect power at the breaker; shut off gas supply if applicable
• Wear cut-resistant gloves—panel edges can be sharp
• Transfer existing control components, brackets, and hardware from the old panel to the new one; label wires or take photos for reference
• All screws and harness connections are secure before restoring power and testing

Color: Black