Washer Dryer Combo Parts

Our washer is next door the bathroom. So when, during the rinse cycle, the hose split and we found the back of the house completely flooded I initially assumed the culprit was either the toilet or the sink or possibly an interdimentional portal into a demonic netherworld of vaguely chlorine scented water. I spent the next hour mopping it all up and checking and re-checking the pipes in the bathroom with no apparent leaks. The next load of laundry left more clues as this time the flood was from... Read more

It was super easy- Pop off the top where the fabric softener goes- undid bolt pop out the agitator ( the hardest part getting this out and the new one in). Got the new one lined up push in place use a rubber mallet to secure put in bolt and good to go May I say this company is excellent- great customer service and delivers as said 5 stars all the way. Read more

• Timer will not advance

I replaced the timer Read more

My appliance repair guy checked out the problem, but the stack washer dryer required the contractor to dismantle the cabinet to allow the repair to occur. So i wanted the parts available for the repair, so we would not have to have the dryer pulled apart in a small space for an extended time i ordered the parts on Friday afternoon and they arrived at my home before noon on Saturday! The contractor and the repairman were able to coordinate the repair on Tuesday morning, and though the... Read more

I looked on Appliance Parts Pros. com and read the problems that others had and replacing the ignitor made sense so I ordered one. It came by UPS within 3 days. I watched the video on how to replace it. Everything went easily, except the screw that held the ignitor in place was a philups head screwdriver and I couldn't get a screwdriver into the small space I had to work in so I went to Harbor Freight Tools and bought an inexpensive 90 degree rachet screwdriver for $2.99 and it worked great.... Read more

I took it apart and cleaned and lubricated the rear support rollers and the belt pulley roller. I think the squealing was coming from the pulley roller. I then replaced the rear felt as it was badly deteriorated. The dryer now runs much more smoothly and quietly. Read more

The parts I purchased from Appliance Parts Pro fit perfectly and were reasonably priced. I received them the next day, which made the Wife (and me) very happy. Although Appliance Parts Pro did not have a repair video for this, I was able to find one online and the machine is washing like new again. The website is well laid out and easy to find what your looking for. Between the available parts and the videos they provide, anyone who is reasonably handy should be able to repair their machine as... Read more

• Too hot

I removed the front panel and observed the heating element while running the dryer. It was cycling off every minute or so and staying off for several minutes. Even though it was likely the high temp cycling thermostat I replaced both the 14, and 15 cycling thermostats which I think are the original factory units. That makes them nearly 35 years old. Problem fixed. Read more

Ordered a new drain hose and extension part. The prices including shipping were more reasonable than driving back and forth to the store just to piece meal parts together. Very frustrating. I ordered the parts that were specific to our washing machine, it took maybe 5 minutes to install, and everything fit perfectly. Now we're washing again and no leaks! Read more

• Will not stop filling with water
• Will not fill with water

Part arrived in one day! Replaced the water valve. YouTube video for replacing water valve on Frigidaire top-loading washers was spot-on. Read more

Installed the new Lid Actuator and the dryers Start Switch. Read more

Ordered and re-place switch and (3) three shocks basically gutting the motor and tub assembly out and reassembling with the detailed instructions sent with new parts Read more

Pushed new knob on Read more

Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more