Washer Dryer Combo Parts

• No heat or not enough heat

Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more

• Won't start

1) Ordered part. 2) Removed front panel by loosening the two screws at the bottom front. 3) Removed old Safety Switch/Lid Lock by disconnecting wires (plug and 2 female disconnects) 4) Reconnected all wires and reinstalled switch. 5) Replaced front panel. 6) Tested Unit. 7) FYI - I found that the locking mechanism stays locked until cycle completely finishes on its own. DO NOT force the cycle to end. Lid will NOT unlock. Read more

Every time I tried to start our dryer, the "Sensing Light" came on, I heard a little "click," and the dryer would not start. According to the very helpful Appliance Parts Pros. videos, I was able to dismantle, diagnose a few components, and discover the broken part. In this case, it was a Broken Belt Switch. I ordered the part, we went on vacation for a week, and when we returned home the part was at our residence. The next day, I installed the part and all is good now. I am nearly 70 years... Read more

Put both thermostats in as I did not know if the unit was cycling on high limit at times. Fixed both issues plus I used my lawn blower and blew all the lint out of dryer and short 3' hose. I also lubed rear drum bearings. Works like new. Ron R Read more

Replaced flow meter and control valve Read more

I replaced the door boot with a new one from AppliancePartsPros.com. The most difficult part was starting at the back end of the new boot onto the stationary rim, just in front of the tub. And then anchoring it in place with the existing spring from the previous boot. To start the boot I had to hook the top edge of the boot, where the arrow tab is, onto the rectangular projection on the tub rim and then roll the rubber boot edge down around the tub rim and hope the rim was going into the... Read more

This is a stacked unit so it comes apart a little different. you DO NOT have to remove the dryer unit to remove the tub assembly.the top front cabinet brace is held on with 6 screws.remove this along with the suspension rods the tub assembly comes straight out the front of the machine. Do yourself a favor and take the whole assembly out of the machine before you disassemble the inner tub. I removed the drain pump before i took the tub out as a precaution. The worst part about this job was the... Read more

My front loader LG washing machine wasn’t working correctly. The clothes were either coming out unwashed or completely dripping. When turning the washer on it would start up like normal and the turn off a few minutes in. Initially it was not displaying an error code, this made it very difficult to diagnose. One of the kids started a load not knowing we are having issues and it started making a clunking cringing noise, when I went to investigate the EL code was up. A few YouTube videos later... Read more

I replaced the thermal cut-off sensors and the cutoff-Tml Read more

First of you need to remove front panel of the washer, using a putty knife push the tabs between the top of the machine and the front panel. Once front panel is exposed drain hose is connected to pump which is in the front of the machine,very easy to access with the front off. Remove old hose with pliers and discard ,run new hose thru outlet on the back of the machine and secure new hose to drain and secure hose to the machine, reinstall front panel of washer and that's it Read more

I checked the continuity on the thermal fuse (which was blown) and knew that it needed to be replaced. This made me question why it blew (i.e. what caused it to fail). I checked continuity on the thermostat (high limit) as well as the thermostat for the element. Both passed a continuity test, so I removed the high limit thermostat to inspect it and could hear it rattling inside. This leads me to believe the spring inside had failed, so I replaced this thermostat as well. Put it back... Read more

First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more

Replaced upper and lower felts. Painted rubbing surface on inside of drum with refrigerator enamel. Took out drum and lubed rear bearing. Replaced 2 of the 3 thermostats, and the belt just on principle. Spent a lot of time with shop-vac removing lint from drier and exhaust ducts. Runs great and is no longer cooking or staining clothes. Read more

The kit was very simple it took longer to take the dryer apart than it did to do the change over and it works great thank you for you're product Read more