Washer Dryer Combo Parts

My problem was a broken spider. I followed your excellent video, but have some additional input that should be incorporated in a new video showing the required upgrade procedures and parts required to repair an early model with damaged front tub half using currently available parts. Don't expect everything to go as easy as the video. 1) Used 4lb. brass hammer to drive shaft from bearings. 2) Torqued spider bolts to 20ft lbs. with thread locking compound. 3) attached rubber seal to front tub... Read more

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

Secured the inner and outer door together and screwed handle back in place. Read more

I replaced the motor. It was time consuming because you have to take all of the parts that attach off. Was fairy simple. Pleased about the parts delivery. Ordered and received the next day. Read more

• Will not drain

When I removed a bunch of very wet soaking towels at the end of a wash cycle, it was clear that the water was not draining properly. The washer also made a very loud noise during the water drain period. That was suspicious. I ordered the part, opened the washer, removed the old pump and faced with a nasty surprise. You may laugh at this, but there was a toothpick in the old drain pump! most of it was still there, and it seemed like the toothpick was stuck in the pump in such a position that it... Read more

Ordered the kit from you. Thank you for shipping so fast. We had the product in 24 hours. Read more

Ordered a new handle from appliancepartspros.com and installed. Read more

This was the second attempt at fixing this problem. The first repair and parts were generated by listing the problem and reviewing the potential corrections, listed on the web site. From making repairs on other clothes washers, I was confident that some of those potential causes could have been the cause. Unfortunately the counterbalance spring and suspension springs were not the cause as they were attached as intended and in good condition. I reached out for Appliance Parts Pros input... Read more

Removed lid. Removed switch panel. Suspected open circuit in thermal fuse. Tested it with a multimeter first to confirm it had an open circuit. This part is obsolete. Contacted manufacturer and found part supercedes to a different part number Ordered part. (This website is very efficient. The part arrived with the 1.7 day promise time.) new fuse bracket is slightly larger due to supercession. Marked bolt hole locations and drilled new. Installed fuse. Re-assembled dryer in reverse order.... Read more

The hardest part of this repair was determining where (controls, motor, belt or transmission) the problem was. I could see little pieces of rubber from the belt beneath the motor pulley, but the machine is 20 years old and some wear is to be expected. Since the belt was still intact and neither frayed or cracked and since I didn't know what the original dimensions were and since the machine was still able to agitate, I could only identify the belt as a possible source of the failure to... Read more

Replacing the timer, timer knob, dial timer, Read more

Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more

By replacing it. Read more

I tried to just replace the speed sensor first which was inexpensive but that did not get it going. So I ordered the motor kit which does not come with a new pulley or speed sensor.Remove the pulley and speed sensor from the old motor and install on the new... Clear the code and its good to go Read more

• Doesn't shut off
• Timer will not advance

I ordered the timer and knob on Monday, they arrived around noon on Tuesday, and within an hour I had them installed and back in business. I was amazed how quickly the parts got here. The online video showing the procedure step by step was very helpful. Instead of disconnecting all the wires and having to keep up with which one went where, I moved each wire one by one and made sure I didn't get any of them in the wrong place. The only thing that slowed me down a bit was seeing which side of the... Read more