Washer Parts

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

• Shakes and moves
• Noisy
• Pumps but will not spin

Replaced washer drive block and Cam. I called around and finally settled on Appliance Parts Pros because they helped diagnose the problem, told me what parts to replace and had videos to show me how to do it. In completing the repair I had to remove quite a few pieces of hardware in order to get at the part I was to replace. The videos helped but there is a learning curve while you familiarize yourself with the parts and figure out how the remove them. Eventually I got to a large nut that,... Read more

Replaced the belt. Read more

We watched the videos posted on AppliancePartsPros.com website several times before starting the work. Once we were confident of the process, we jumped in with the complete disassembly of the washing machine's drum rotating assembly...everything that touched the drum or made it rotate. My son and I disassembled and inspected each part for wear/damage and ordered replacement parts based on condition. The parts came in within 3 days of ordering. My son and I took 3 hours to reassemble and... Read more

Remove one bolt in the center of the agitator need a long extension, couldn't be any easier. Read more

I ordered the parts, after assuring my diagnosis was correct from APP’s knowledgeable representative, and they were shipped quickly. I tipped the washer and disassembled the parts to be replaced and then installed a new clutch, clutch spring and mode shifter. Read more

After researching the problem on this site, I realized that the most likely cause was a bad bearing contained in the shaft & tube assembly. Essentially, the tub seal failed & allowed water to travel down the shaft & into the housing containing the bearing. I confirmed this by pulling the front cover off of the unit & noticed some brown water pooled directly under the shaft & tube assembly. I followed the disassembly instructions on this site & it wasn't too bad but did take some time as pretty... Read more

• Burning smell
• Will not agitate
• Spins slowly
• Pumps but will not spin

I Purchased a new belt and replaced it. If I had not watched the video telling me how it is done the job would have been much more difficult. After watching the video I changed the belt in less than 2 minutes. I ordered the belt from Appliance Parts Pros and got it the next day. I am thankful that when I started my search I landed on your web site. Thanks for the quick service and the video. Read more

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more

First went through the troubleshooting guide on the website and read the various stories and watched the repair videos for replacing the springs and suspension pads. Then before ordering any parts disassembled the machine only to the point of removing the cabinet to see if there were any obvious issues. The springs appeared OK but I couldn't tell of they were fatigued or not and all were in place but the tub suspension pads were definitely worn out. I then put the machine back together and went... Read more

• Noisy

Using appliancepartspros.com site took washer apart to diagnose bad clutch. The clutch was bad but once inside I noticed grease everywhere and after a quick online chat with rep. determined gear case was leaking and needed replacement. Replaced clutch & gear case. Followed video tutorial and took a little more than 30 minutes start to finish for me - I have no experience. The most difficult part for me was actually just getting the retainer ring (little wire) to secure clutch in place-took... Read more

Watched a YouTube video. Read more

Our 10-year-old LG WM2487HWMA front load washer had gradually developed multiple problems. It sounded like a jet engine during high speed spin, both the drain pump and circulation pumps were noisy, it would not drain properly (water was coming in during spin cycle), no water was spraying out at the top of the door into the drum like it is supposed to when the circulation pump was running. It's amazing we had still been able to wash clothes at all! With the help of the excellent... Read more

Replaced the door latch/lock assembly. Read more

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

After looking up the model number of my washing machine on AppliancePartsPros.com I ordered the suspension rod kit, two sets of tub centering springs (one spring per corner), a Ring-Tub (mine was breaking apart due to banging around) and a spare suspension bearing kit in case I need it later. I spoke to a very helpful customer service rep on the phone just before placing my order. They have customer service representatives answering the phone late at night. I was surprised. All of my parts were... Read more