General Electric Housing Or Cover

This cover plate is a factory-style trim panel that protects and finishes the appliance's control area and internal components, restoring a clean appearance and helping keep wiring and switches shielded from debris. What it does

• Covers and protects the appliance control area and underlying components
• Restores a finished look to a damaged or missing trim panel
• Helps prevent dust and spills from reaching electrical parts or switches
• Matches OEM fit and mounting points for a secure replacement

• One cover plate (trim panel)

• High-level replacement; typically removed and installed with basic hand tools
• Disconnect power to the appliance before starting to avoid shock or injury
• Inspect mounting clips and fasteners and replace if worn for a secure fit

This igniter cover is a replacement protective shield that helps protect the oven igniter from food spills and debris, extending the igniter's service life and helping the burner ignite reliably. What it does:

• Shields the oven igniter from direct contact with spills, drips and falling debris
• Helps prevent premature igniter damage that can lead to ignition problems
• Can reduce the chance of shorting or erratic ignition caused by contamination
• Matches original shape to ensure proper fit and clearance around the igniter

• Disconnect power to the appliance (and shut off gas if applicable) before servicing
• Allow the oven to cool completely and wear gloves to avoid cuts from sheet metal
• Handle the igniter and cover carefully; avoid touching the igniter surface directly
• Test appliance operation after reinstall

This boot auger motor powers the auger inside the ice dispenser boot to move ice from the bin into the dispenser chute. Replacing a worn motor restores normal ice dispensing and stops auger-related jams or no-dispense issues. What it does:

• Rotates the ice auger inside the dispenser boot to feed ice toward the chute.
• Restores ice dispensing when the auger does not turn or dispenses intermittently.
• Stops symptoms such as humming from the dispenser area, no ice output, or auger binding.
• Works with the dispenser drive components to deliver measured ice portions.

• Disconnect power to the appliance before beginning work to avoid shock or injury.
• Remove the ice bucket/door panels as required to access the dispenser boot and auger assembly.
• Handle electrical connections and mounting hardware carefully; match wire connectors and routing during reassembly.
• After install, restore power and test the dispenser through several cycles to ensure proper auger rotation and operation.

This replacement crusher dispenser housing restores the outer housing that supports the ice crusher and dispenser chute, helping the dispenser operate smoothly and keep ice contained while in use. What it does:

• Replaces cracked or broken dispenser housing that can allow ice to jam or fall out
• Provides the proper mounting surface for the crusher and chute to align ice flow
• Helps reduce noise and rubbing caused by a misaligned or damaged housing
• Restores the dispenser's outer enclosure for a finished appearance and safe operation

• Disconnect power to the refrigerator before starting any repair.
• Remove ice bin and dispenser components as needed to access the housing; keep track of fasteners.
• Inspect adjacent seals, gaskets and mounting clips and replace if damaged.
• Handle plastic parts carefully to avoid cracking; reassemble components to factory alignment.

This evaporator cover replaces the bottom refrigerator/freezer evaporator housing to protect internal components and help direct airflow for consistent cooling. Restores proper airflow paths and shields the evaporator from debris. What it does:

• Covers and protects the evaporator coil and associated components in the lower section
• Directs cold airflow through the evaporator chamber to support even cooling
• Helps prevent frost and ice buildup by maintaining correct airflow patterns
• Can reduce intermittent temperature issues or moisture accumulating inside the compartment

• Disconnect power to the appliance before starting any repair
• Remove surrounding panels or shelving to access the evaporator area; support the cover while unfastening mounting hardware
• Inspect and replace any damaged mounting clips or insulation as needed
• If the evaporator area is iced, fully defrost and dry the compartment before installing the new cover

This lower interior light housing assembly replaces a cracked or damaged refrigerator lower light housing and restores the light fixture mounting and lens for proper illumination of the fresh-food compartment. What it does:

• Replaces the lower interior light housing and lens assembly to secure the light and lens in place
• Restores proper alignment and protection for the lower refrigerator light
• Helps stop rattling or movement caused by a broken housing
• Addresses symptoms like a loose or missing lens, exposed bulb, or improper light positioning

• One lower interior light housing assembly (housing with lens as shown)

• Disconnect power to the appliance before starting any repair
• Remove the existing housing carefully to avoid damaging the bulb or wiring
• Retain or reuse the original bulb unless explicitly replacing it
• Use proper fasteners and alignment tabs;