General Electric Leg Or Foot

This replacement leveling screw secures and adjusts an appliance's leg so the unit sits level and stable on the floor. Restores proper tilt for even door operation and stable performance. What it does:

• Replaces a worn or damaged leveling screw used to raise or lower an appliance leg
• Helps stop rocking, reduce vibration, and keep doors aligned
• Common fix when an appliance tilts forward/back or is uneven on the floor
• Works with the corresponding leveling leg/assembly to set final height

• Support the appliance before adjusting or removing leveling hardware to prevent tipping
• Use appropriate hand tools; tighten securely but avoid over-torquing
• No electrical disconnection is typically required, but unplug if working near electrical components
• If the leveling leg assembly is damaged, replace the entire leg/assembly per manufacturer instructions

The Mobility Wheel S Kit is an OEM part for GE refrigerators. This kit includes the necessary components to replace or install the wheels on the bottom of your refrigerator cabinet, allowing for easy movement and repositioning of the appliance.

A bad mobility wheel assembly can be caused by normal wear and tear over time, damage due to heavy loads or rough handling, or malfunctioning wheel mechanisms. If you find it difficult to move or reposition your refrigerator, or if the existing wheels are damaged, it may be time to replace the mobility wheel assembly.

Symptoms of a bad wheel assembly include:

• Difficulty in moving or sliding the refrigerator
• Uneven or unstable positioning of the appliance
• Excessive noise or scraping sounds when moving the refrigerator
• Damaged or worn-out wheels

Replace your faulty mobility wheel assembly with this genuine OEM part to restore your refrigerator. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This rear mobility wheel replaces a worn or broken wheel on the back of your refrigerator, restoring smooth rolling movement so you can pull the unit out safely for cleaning, servicing, or leveling without dragging or floor damage.

• Mounts to the rear base/roller bracket to support and roll the refrigerator for positioning or service
• Replace if the wheel is cracked, missing, flat-spotted, or seized
• Common symptoms: unit is hard to move, scrapes the floor, sits unevenly, or makes grinding noises when moved
• Helps maintain proper cabinet support during movement

• Disconnect power and turn off the water supply before servicing
• Protect flooring and use a helper—appliances are heavy and can tip
• Access the rear base area; remove the old wheel and install the new wheel using the existing hardware
• After re-positioning, re-level the refrigerator per the owner's manual

This replacement wheel slide restores smooth movement to a refrigerator drawer by guiding the drawer along its track and supporting its weight. It helps stop sticking, sagging, or grinding so drawers open and close reliably. What it does

• Guides and supports a refrigerator or freezer drawer along its track for smooth operation
• Replaces damaged, worn, or missing slides that cause sticking or uneven movement
• Helps stop drawers from sagging or coming off the track
• Works with the drawer roller system to reduce grinding and binding noises

• One wheel slide

• Disconnect power to the appliance or unplug before service to avoid electrical risk
• Remove the drawer and existing slide; installation typically requires basic hand tools and alignment on the track
• Inspect adjacent rollers and track for wear; replace if damaged for best performance
• Handle plastic parts carefully to avoid cracking; test drawer movement before returning items to the drawer

This replacement leveling foot stabilizes and supports the appliance so it sits level and steady on the floor. Restores proper alignment for doors and drawers and reduces wobble or rocking. What it does:

• Replaces a worn or damaged support foot to restore proper appliance height and balance
• Helps stop rocking, tipping, or uneven operation caused by an unstable base
• Can improve door alignment and sealing by returning the appliance to a level position
• Quietly supports normal appliance movement without introducing vibration

• Disconnect power and empty or secure contents before adjusting or replacing feet
• Support the appliance with a block or helper to prevent tipping while swapping the foot
• Thread or snap into place per the appliance's mounting design; tighten by hand or with appropriate tool
• Re-level the appliance after installation and verify doors/drawers open and close smoothly

This rear wheel assembly replaces a worn or broken refrigerator drawer roller to restore smooth, stable movement and proper drawer alignment. It helps prevent sticking, scraping, and uneven wear on the drawer track. What it does:

• Replaces a damaged rear roller so the drawer opens and closes smoothly
• Keeps the drawer aligned and prevents it from binding or tilting
• Reduces scraping and uneven wear on the drawer and track
• Supports normal load on the rear of the drawer for stable operation

• Remove drawer contents and slide the drawer out according to your appliance manual before starting
• Inspect the front and rear tracks; replace only the damaged roller(s) and test drawer movement after installation
• Use basic hand tools; avoid forcing parts
• No special wiring or electronic handling required; follow general safety precautions

This foot pad cushions and supports an appliance leg to reduce vibration and protect flooring. It helps stabilize and level the unit for quieter operation and prevents metal-to-floor contact that can cause scratches or noise. What it does:

• Cushions the appliance leg to absorb vibration and reduce noise
• Helps stabilize and level the appliance to prevent rocking or tilting
• Protects hard floors and finishes from scuffs and scratches
• Can reduce movement that contributes to rattling or squeaking during operation

• Disconnect power and water and follow appliance safety procedures before working underneath the unit
• Raise or tilt the appliance only as recommended by the manufacturer; use a helper or a suitable jack for safety
• Slide or press the foot pad onto the appliance leg until fully seated; the appliance sits level and stable
• Re-check level after a short test run and adjust feet as needed

This wheel axle is the replacement shaft that secures a dryer drum roller wheel, helping the drum turn smoothly and quietly. It restores proper wheel alignment to reduce wobble, noise and uneven drum movement. What it does:

• Holds the drum roller wheel in place so the dryer drum rotates evenly
• Restores stable drum support to reduce scraping, squeaking or grinding sounds
• Helps prevent premature wear on the roller wheel and drum bearing
• Supports smooth drum rotation to improve drying consistency

• One wheel axle

• Disconnect power before beginning any repair; follow all safety precautions
• Access may require removing the dryer front panel or drum
• Inspect roller wheel and surrounding components; replace worn parts together for best results
• Tighten and align components per OEM guidance; avoid forcing parts to prevent damage

This replacement roller pan supports and guides the oven or range storage drawer, restoring smooth sliding and helping contain spills or crumbs under the drawer. It installs behind the drawer to stabilize rollers and track movement. What it does:

• Holds and aligns the storage-drawer rollers so the drawer opens and closes smoothly
• Helps contain crumbs and minor spills beneath the drawer area
• Reduces drawer sagging, sticking or noisy operation when rollers are worn or damaged
• Restores proper drawer tracking and prevents misalignment

• One replacement roller pan

• Disconnect power to the appliance before servicing to avoid injury
• Remove the oven/storage drawer to access the pan
• Inspect rollers and bracket hardware; replace any damaged fasteners or rollers as needed
• Use basic hand tools; reassemble carefully and test drawer operation after installation

This is the right side pan roller. For left side use WR2X8595.

This is the right side basket roller. For left side use WR2X8615.